Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0231250 SFI SYSTEM(w/o Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P001100  Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1  P001200  Camshaft Position "A" - Timing Over-Retarded Bank 1  


DESCRIPTION

Refer to DTC P001013.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>P001013

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001100 Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Camshaft timing gear assembly

·

Oil control valve filter

·

ECM


Comes on DTC stored SAE Code: P0011
P001200 Camshaft Position "A" - Timing Over-Retarded Bank 1 Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Camshaft timing gear assembly

·

Oil control valve filter

·

ECM


Comes on DTC stored SAE Code: P0012

MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the Variable Valve Timing (VVT) system to control the intake camshaft. The VVT system includes the ECM, camshaft timing oil control valve assembly and VVT controller (camshaft timing gear assembly). The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.

If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as a VVT controller stuck malfunction and stores a DTC.

Example:

A DTC is stored when the following conditions are met:

1.

It takes 5 seconds or more to change the valve timing by 5°CA.

2.

After the above condition is met, the camshaft timing oil control valve assembly is forcibly activated for 9.5 seconds or more.



DTC P001100 (Advanced Camshaft Timing) is subject to 1 trip detection logic.

DTC P001200 (Retarded Camshaft Timing) is subject to 2 trip detection logic.

These DTCs indicate that the VVT controller cannot operate properly due to a camshaft timing oil control valve assembly malfunction or the presence of foreign matter in the camshaft timing oil control valve assembly.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing oil control valve assembly
Camshaft timing gear assembly
Required Sensors/Components (Related) Crankshaft position sensor
Camshaft position sensor
Engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A217996E48
2.635,2.635 2.271,3.385 2.271,3.385 2.354,3.385 false 0.198,0.281 1.115,0.479 0.917,0.198 10 false Vehicle Speed 0.094,1.146 1.115,1.781 1.021,0.635 10 false 75 km/h or more [Engine running] 0.76,2.083 1.115,2.271 0.354,0.188 10 false Idling 0.25,2.344 1.115,2.698 0.865,0.354 10 false Power Switch on (IG) 1.396,2.354 1.698,2.573 0.302,0.219 10 false [A] 1.896,2.042 2.25,2.26 0.354,0.219 10 false [B] 2.49,1.552 2.781,1.802 0.292,0.25 10 false [C] 4.188,2.021 4.573,2.302 0.385,0.281 10 false [D] 4.75,1.552 5.135,1.896 0.385,0.344 10 false [F] 4.479,3.156 4.688,3.333 0.208,0.177 10 false [E] 6.458,2.031 6.885,2.24 0.427,0.208 10 false [G] 6.74,3.146 6.948,3.323 0.208,0.177 10 false [H] 1.594,2.719 2.396,3.031 0.802,0.313 10 false Warming up 2.375,3.323 3.656,3.479 1.281,0.156 10 false 10 seconds or more 4.667,2.729 5.385,3.083 0.719,0.354 10 false 10 seconds or more 3.708,2.719 4.51,3.052 0.802,0.333 10 false 100 seconds or more 5.948,2.719 6.76,3.042 0.813,0.323 10 false 100 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

HINT:
·

If P001100 was output:

Clear the DTC without using the GTS.

·

If P001200 was output:

Clear the DTC using the GTS.



5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [B].

10.

With the engine running, accelerate the vehicle to 75 km/h (46 mph) or more by depressing the accelerator pedal for 10 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


11.

Idle the engine for 100 seconds or more [D].

12.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P001100 or P001200.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform steps [F] through [H].



17.

With the engine running, accelerate the vehicle to 75 km/h (46 mph) or more by depressing the accelerator pedal for 10 seconds or more [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


18.

Idle the engine for 100 seconds or more [G].

19.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

20.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTCs are not output, perform the following procedure.



21.

Check the DTC judgment result again.

HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




CAUTION / NOTICE / HINT

HINT:
·

DTC P001100 or P001200 may be stored when foreign matter in the engine oil is caught in parts of the system. The DTC will remain stored even if the system returns to normal after a short time. The foreign matter may then be captured by the oil filter.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001100 OR P001200)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P001100 or P001200 is output A
DTC P001100 or P001200 and other DTCs are output B


HINT:

If any DTCs other than P001100 or P001200 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 / Data List / Intake VVT Change Angle Bank 1.

Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
50004 372 4 397

g.

Read the Data List while performing the Active Test with the engine idling.

OK:
GTS Operation Data List (Intake VVT Change Angle Bank 1)
-100% to 100% Varies by 70 DegFR or more


HINT:
·

Test not possible with park (P) selected during charge control. Select neutral (N) to perform test.

·

If DTCs are stored after the Active Test, clear the DTCs.




Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372
HINT:
·

If P001100 was output:

Clear the DTC without using the GTS.

·

If P001200 was output:

Clear the DTC using the GTS.




e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001100 or P001200 is output B


HINT:

DTC P001100 or P001200 may be stored when foreign matter in the engine oil is caught in parts of the system. The DTC will remain stored even if the system returns to normal after a short time. The foreign matter may then be captured by the oil filter.




A

B

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

6.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
a.

Remove the cylinder head cover sub-assembly.

A378041C01
1.281,2.656 0.667,2.25 0.667,2.25 0.5,2.25 true 2.781,3 3.25,2.333 3.25,2.333 3.417,2.333 true 4.563,2.302 4.833,1.167 4.833,1.167 5,1.167 true 4.385,2.521 4.083,3.333 4.083,3.333 3.917,3.333 true 2.719,0.281 3.031,0.479 0.313,0.198 10 false *a 0.313,2.167 0.625,2.365 0.313,0.198 10 false *b 3.469,2.26 3.781,2.458 0.313,0.198 10 false *b 5.052,1.094 5.365,1.292 0.313,0.198 10 false *c 3.729,3.25 4.042,3.448 0.313,0.198 10 false *d
*a 39.5° *b Timing Mark
*c "0" Timing Mark *d Groove



b.

Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain or belt cover sub-assembly.


c.

Check that the timing marks of the camshaft timing gear assembly and camshaft timing sprocket are at the positions shown in the illustration.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

Timing marks on camshaft timing gear assembly and camshaft timing sprocket are at the positions shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

7.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

NG

9.CHECK ENGINE MECHANICAL SYSTEM
7.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
a.

Inspect the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

8.INSPECT OIL CONTROL VALVE FILTER
A375301C01
1.813,0.5 2.063,0.25 2.063,0.25 2.313,0.25 false 2.365,0.177 2.677,0.333 0.313,0.156 10 false *1
*1 Oil Control Valve Filter


a.

Remove the oil control valve filter.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG



OK

10.CLEAR DTC

NG

9.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

10.CLEAR DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

10.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372
HINT:
·

If P001100 was output:

Clear the DTC without using the GTS.

·

If P001200 was output:

Clear the DTC using the GTS.




e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001100 or P001200 is output B




A

B