Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0231250 SFI SYSTEM(w/o Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P010012  Mass or Volume Air Flow Sensor "A" Circuit Short to Battery  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the intake air volume. The ECM uses this information to determine the ignition timing and fuel injection duration necessary for an optimal air fuel ratio. Inside the mass air flow meter sub-assembly are a hot wire element and a cold wire element which are exposed to the flow of intake air. The temperature sensor bridge circuit shown in the illustration outputs voltage to transmit information regarding heat loss of the hot wire element caused by air flow. Depending on the air flow, this voltage will change between approximately 0.2 V and 4.9 V. Based on this voltage, the ECM calculates the air flow to determine the ignition timing and fuel injection duration necessary for an optimal air fuel ratio.

HINT:

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A160257E09
1.969,1.938 2.427,1.51 2.427,1.51 2.573,1.51 false 5.406,1.99 5.021,2.771 5.021,2.771 4.896,2.771 true 5.781,2 5.281,3.063 5.281,3.063 5.156,3.063 true 6.302,2.031 5.854,3.354 5.854,3.354 5.188,3.354 true 1.594,1.927 1.313,1 1.313,1 1.229,1 true 4.375,0.865 4.833,0.438 4.833,0.438 4.979,0.438 false 1.667,0.531 2.583,1.021 0.917,0.49 10 false +B 0.042,0.938 1.542,1.438 1.5,0.5 10 false Cold Wire Element 2.625,1.438 4.083,1.75 1.458,0.313 10 false Hot Wire Element 2.573,2.031 3.74,2.281 1.167,0.25 10 false Output Voltage 2.802,2.677 4.938,3.042 2.135,0.365 10 false Temperature Sensor (Thermistor) 4.063,3.292 5.396,3.594 1.333,0.302 10 false Hot Wire Element 3.969,2.979 5.167,3.198 1.198,0.219 10 false Cold Wire Element 1.938,1.042 3.323,1.271 1.385,0.229 10 false Power Transistor 5.052,0.375 6.365,0.958 1.313,0.583 10 false Mass Air Flow Meter Sub-assembly

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P010012 Mass or Volume Air Flow Sensor "A" Circuit Short to Battery Both of the following conditions are met for 3 seconds or more: (1 trip detection logic)
·

The mass air flow meter sub-assembly voltage is higher than 4.9 V.

·

The engine speed is less than 4000 rpm.


·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on DTC stored SAE Code: P0103

HINT:

When these DTCs are output, check the mass air flow rate in the Data List. Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.

DTC No. Mass Air Flow Sensor Malfunction
P010012 271.0 gm/sec or more
·

Short in VG circuit to power source circuit

·

Open in E2G circuit



If the Data List value is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

If the mass air flow meter sub-assembly is malfunctioning or there is an open or short in the mass air flow meter sub-assembly circuit, the voltage will deviate from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly circuit, illuminate the MIL and stores a DTC.

Example:

When the sensor output voltage remains higher than 4.9 V for 3 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P010012.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A376234E03
6.396,3.229 6.865,3.49 0.469,0.26 10 false ECM 5.833,2.792 6.292,2.99 0.458,0.198 10 false A40 5.854,2.604 6.167,2.802 0.313,0.198 10 false 46 6.156,2.698 6.771,2.896 0.615,0.198 10 false MREL 5.833,1.229 6.292,1.427 0.458,0.198 10 false C31 5.813,1.052 6.167,1.229 0.354,0.177 10 false 104 6.146,1.125 6.604,1.323 0.458,0.198 10 false E2G 5.833,0.677 6.292,0.875 0.458,0.198 10 false C31 5.823,0.479 6.281,0.677 0.458,0.198 10 false 137 6.146,0.563 6.458,0.76 0.313,0.198 10 false VG 5.021,1.615 5.792,1.813 0.771,0.198 10 false Shielded 4.719,0.583 4.875,0.781 0.156,0.198 10 false 3 4.729,1.125 4.885,1.323 0.156,0.198 10 false 2 3.333,0.25 3.49,0.448 0.156,0.198 10 false 1 3.49,0.26 3.802,0.458 0.313,0.198 10 false +B 4.417,0.583 4.729,0.781 0.313,0.198 10 false VG 4.354,1.125 4.813,1.323 0.458,0.198 10 false E2G 2.573,0.521 3.698,0.938 1.125,0.417 10 false EFI NO. 3 3.24,1.594 3.552,1.792 0.313,0.198 10 false C5 3.469,1.583 4.75,2.063 1.281,0.479 10 false Mass Air Flow Meter Sub-assembly 1.281,1.635 1.594,1.833 0.313,0.198 10 false 1B 0.688,0.26 0.844,0.458 0.156,0.198 10 false 3 1.073,1.604 1.229,1.802 0.156,0.198 10 false 5 2.417,0.802 2.573,1 0.156,0.198 10 false 6 2.417,0.271 2.573,0.469 0.156,0.198 10 false 4 1.302,1.792 3.052,2.052 1.75,0.26 10 false No. 1 Integration Relay 1.354,1.26 2.01,1.479 0.656,0.219 10 false EFI-MAIN 0.344,1.667 1.26,2 0.917,0.333 10 false EFI-MAIN 0.375,2.458 1.75,2.656 1.375,0.198 10 false BATT-MAIN 0.51,3.063 2.073,3.396 1.563,0.333 10 false Auxiliary Battery 6.563,0.948 7.083,1.167 0.521,0.219 10 false 200 kΩ

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-2 (E2G) - C31-104 (E2G) Always Below 1 Ω
C5-3 (VG) or C31-137 (VG) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RESISTANCE OF ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (RESISTANCE OF ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-3 (VG) - C5-2 (E2G) Power switch off 190 to 210 kΩ
C5-2 (E2G) - Body ground Power switch off Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG