Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0231250 SFI SYSTEM(w/o Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P056014  System Voltage Circuit Short to Ground or Open  


MONITOR DESCRIPTION

The auxiliary battery supplies electricity to the ECM even when the power switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the auxiliary battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. The ECM will illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P056014 System Voltage Circuit Short to Ground or Open An open or short in the ECM backup power source circuit (1 trip detection logic).
·

Open or short in back up power source circuit

·

Auxiliary battery

·

Auxiliary battery terminals

·

ECM


Comes on DTC stored SAE Code: P0562

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met -
Continuous auxiliary battery voltage (BATT) Less than 3.5 V
Electronic throttle actuator power supply voltage (+BM) Less than 3.5 V

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P056014.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A378091E03
0.854,2.698 2.25,3.052 1.396,0.354 10 false Auxiliary Battery 0.719,2.083 2.094,2.281 1.375,0.198 10 false BATT-MAIN 3.646,1.135 4.333,1.344 0.688,0.208 10 false EFI-MAIN 3.74,1.833 4.354,2.031 0.615,0.198 10 false ETCS 5.833,3 6.302,3.25 0.469,0.25 10 false ECM 4.938,0.969 5.396,1.167 0.458,0.198 10 false A40 5,0.781 5.156,0.979 0.156,0.198 10 false 1 5.271,0.875 5.885,1.073 0.615,0.198 10 false BATT 4.938,1.677 5.396,1.875 0.458,0.198 10 false C31 4.969,1.49 5.281,1.688 0.313,0.198 10 false 29 5.271,1.563 5.729,1.76 0.458,0.198 10 false +BM 4.938,2.375 5.396,2.573 0.458,0.198 10 false C31 4.969,2.188 5.281,2.385 0.313,0.198 10 false 59 5.292,2.365 5.604,2.563 0.313,0.198 10 false E1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AUXILIARY BATTERY
a.

Inspect the auxiliary battery.

Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION

OK:

Auxiliary battery voltage is between 11 to 14 V.



Result:
Proceed to
OK
NG



OK

2.CHECK AUXILIARY BATTERY TERMINAL

NG

CHARGE OR REPLACE AUXILIARY BATTERY

2.CHECK AUXILIARY BATTERY TERMINAL
a.

Check that the auxiliary battery terminals are not loose or corroded.

Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION

OK:

Auxiliary battery terminals are not loose or corroded.



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

NG

REPAIR OR REPLACE AUXILIARY BATTERY TERMINAL

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.

Disconnect the ECM connector.

A378092C02
0.573,1.25 0.885,1.531 0.313,0.281 3.802,1.25 4.135,1.531 0.333,0.281 1.333,2.01 1.667,1.219 true 6.625,2.063 6.396,1.292 true 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a 0.615,1.313 0.938,1.552 0.323,0.24 10 false A40 3.854,1.313 4.167,1.521 0.313,0.208 10 false C31 1.135,2.073 1.75,2.271 0.615,0.198 10 false BATT 6.521,2.125 6.979,2.323 0.458,0.198 10 false +BM
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-1 (BATT) - Body ground Always 11 to 16 V
C31-29 (+BM) - Body ground Always 11 to 16 V



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - ECM)

4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P056014)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P056014)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Wait 5 seconds or more.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P056014 is output B




A

B