Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0231250 SFI SYSTEM(w/o Canister Pump Module) J

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is being cranked, the start request signal output from the hybrid vehicle control ECU is input to the ECM, and the NE signal generated by the crankshaft position sensor is also input to the ECM. Thus, the ECM interprets that the engine is being cranked, and turns an internal transistor on, causing current to flow to the C/OPN relay. The fuel pump then operates the NE signal is input into the ECM with the engine running, the ECM keeps the transistor on.

WIRING DIAGRAM

A376208E01
6.167,2.313 6.781,2.51 0.615,0.198 10 false MREL 6.167,4.5 6.781,4.698 0.615,0.198 10 false FC 5.896,2.313 6.51,2.51 0.615,0.198 10 false 46 5.896,4.51 6.51,4.708 0.615,0.198 10 false 41 6.563,5.042 6.979,5.281 0.417,0.24 10 false ECM 5.844,0.75 6.458,0.948 0.615,0.198 10 false IG1D 5.583,0.75 6.198,0.948 0.615,0.198 10 false 17 5.594,1.052 6.208,1.25 0.615,0.198 10 false F1 5.594,1.208 7.115,1.615 1.521,0.406 10 false Certification ECU (Smart Key ECU Assembly) 6.24,5.042 6.656,5.281 0.417,0.24 10 false A40 3.021,4.354 3.531,4.604 0.51,0.25 10 false C/OPN 3.604,4.229 4.594,4.552 0.99,0.323 10 false ECU-IG2 NO. 1 4.74,2.823 5.354,3.021 0.615,0.198 10 false 9 4.198,2.833 4.813,3.031 0.615,0.198 10 false 4 4.427,2.833 5.042,3.031 0.615,0.198 10 false 1A 3.896,2.833 4.51,3.031 0.615,0.198 10 false 1B 4.823,2.427 5.438,2.625 0.615,0.198 10 false 1B 4.875,2.229 5.49,2.427 0.615,0.198 10 false 6 4.823,1.177 5.438,1.375 0.615,0.198 10 false 1A 4.875,0.969 5.49,1.167 0.615,0.198 10 false 7 2.969,2.698 3.958,3.021 0.99,0.323 10 false EFI-MAIN 2.948,1.448 3.938,1.771 0.99,0.323 10 false IG2 NO. 1 3.583,3.625 4.198,3.823 0.615,0.198 10 false 5 3.583,3.969 4.198,4.167 0.615,0.198 10 false 1 2.833,3.615 3.448,3.813 0.615,0.198 10 false 3 2.833,3.969 3.448,4.167 0.615,0.198 10 false 2 1.438,3.958 2.052,4.156 0.615,0.198 10 false 4 1.438,4.927 2.052,5.125 0.615,0.198 10 false 5 1.406,4.188 2.021,4.385 0.615,0.198 10 false B 1.406,4.698 2.021,4.896 0.615,0.198 10 false E 0.563,4.49 1.115,4.979 0.552,0.49 10 false Auxiliary Battery 1.896,4.469 2.323,5.021 0.427,0.552 10 false Fuel Pump 1.896,4.302 2.323,4.854 0.427,0.552 10 false M10 0.385,3.302 1.167,3.708 0.781,0.406 10 false BATT-MAIN 0.75,0.99 1.531,1.396 0.781,0.406 10 false IG2-MAIN 0.74,2.26 1.729,2.583 0.99,0.323 10 false EFI-MAIN 1.76,0.844 2.375,1.042 0.615,0.198 10 false 1A 1.76,1.188 2.375,1.385 0.615,0.198 10 false 1A 1.76,2.094 2.375,2.292 0.615,0.198 10 false 1B 1.781,0.656 2.396,0.854 0.615,0.198 10 false 10 1.813,1.01 2.427,1.208 0.615,0.198 10 false 8 1.813,1.896 2.427,2.094 0.615,0.198 10 false 3 1.76,2.427 2.375,2.625 0.615,0.198 10 false 1B 1.813,2.26 2.427,2.458 0.615,0.198 10 false 5 2.073,3.063 3.531,3.375 1.458,0.313 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE CIRCUIT RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 38

e.

According to the display on the GTS, perform the Active Test and check that fuel pump operating sounds can be heard.

OK:

Operating sounds can be heard from the fuel pump.


Result:
Proceed to
OK
NG




OK

2.READ VALUE USING GTS (ENGINE SPEED)

NG

3.INSPECT RELAY (C/OPN RELAY)
2.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

f.

Read the values displayed on the GTS while the engine is cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.INSPECT RELAY (C/OPN RELAY)

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)

NG

REPLACE RELAY (C/OPN RELAY)

4.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)
a.

Remove the C/OPN relay from the No. 2 relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (C/OPN relay) - A40-41 (FC) Always Below 1 Ω
2 (C/OPN relay) or A40-41 (FC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - C/OPN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - C/OPN RELAY)
a.

Disconnect the No. 1 integration relay connector.


b.

Remove the C/OPN relay from the No. 2 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1A-9 - 1 (C/OPN relay) Always Below 1 Ω
1B-4 - 5 (C/OPN relay) Always Below 1 Ω
1A-9 or 1 (C/OPN relay) - Body ground and other terminals Always 10 kΩ or higher
1B-4 or 5 (C/OPN relay) - Body ground and other terminals Always 10 kΩ or higher



HINT:

If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)
a.

Remove the C/OPN relay from the No. 2 relay block.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (C/OPN relay) - M10-4 (B) Always Below 1 Ω
3 (C/OPN relay) or M10-4 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
a.

Disconnect the fuel pump connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M10-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT FUEL PUMP
a.

Result:
Proceed to
OK
NG



OK

NG