Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0239522 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transmits switch signals through the AVC-LAN.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E277861E31
4.427,1.844 6.896,2.063 2.469,0.219 10 false Stereo Component Amplifier Assembly 0.458,1.844 3.125,2.073 2.667,0.229 10 false Radio and Display Receiver Assembly 0.938,2.396 2.938,2.615 2,0.219 10 false : AVC-LAN Communication Line 5.083,0.385 5.698,0.583 0.615,0.198 10 false TX+ 5.083,1.188 5.698,1.385 0.615,0.198 10 false TX- 4.427,1.667 5.042,1.865 0.615,0.198 10 false F61 0.458,1.656 1.073,1.854 0.615,0.198 10 false F31 1.76,0.396 2.375,0.594 0.615,0.198 10 false TX1+ 1.792,1.177 2.406,1.375 0.615,0.198 10 false TX1- 2.156,0.26 2.771,0.458 0.615,0.198 10 false 7 2.146,1.052 2.76,1.25 0.615,0.198 10 false 8 4.906,0.26 5.521,0.458 0.615,0.198 10 false 8 4.906,1.042 5.521,1.24 0.615,0.198 10 false 7

CAUTION / NOTICE / HINT

HINT:

The radio and display receiver assembly is the master unit.


PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.
E221758C17
1.323,1.76 1.615,1.229 false 2.083,1.75 1.792,1.219 false 0.135,0.083 0.302,0.26 0.167,0.177 10 false *a 1.146,1.792 1.469,1.969 0.323,0.177 10 false TX1- 1.969,1.781 2.323,1.958 0.354,0.177 10 false TX1+
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (TX1+) - 8 (TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the F31 radio and display receiver assembly connector.


b.

Disconnect the F61 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-7 (TX1+) - F61-8 (TX+) Always Below 1 Ω
F31-8 (TX1-) - F61-7 (TX-) Always Below 1 Ω
F31-7 (TX1+) or F61-8 (TX+) - Body ground Always 10 kΩ or higher
F31-8 (TX1-) or F61-7 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY