Home › Vehicle Interior › METER / GAUGE / DISPLAY › HEADUP DISPLAY SYSTEM
RM3210E _58 Vehicle Interior _047509 METER / GAUGE / DISPLAY _0241557 HEADUP DISPLAY SYSTEM J

METER / GAUGE / DISPLAY  HEADUP DISPLAY SYSTEM  Main Switch Circuit  


DESCRIPTION

The headup display switch (No. 2 combination switch assembly) and combination meter mirror ECU are connected via direct line. The combination meter mirror ECU can be turned off and on by operating the headup display switch (No. 2 combination switch assembly).

WIRING DIAGRAM

E274717E25
0.792,2.385 1.083,2.552 0.292,0.167 10 false F49 0.792,2.563 3.406,2.969 2.615,0.406 10 false Headup Display Switch (No. 2 Combination Switch Assembly) 2.688,0.875 2.99,1.073 0.302,0.198 10 false ILU 2.792,2.052 2.948,2.292 0.156,0.24 10 false E 3.01,2.052 3.177,2.229 0.167,0.177 10 false 10 3.021,0.865 3.188,1.042 0.167,0.177 10 false 3 4.385,0.865 4.552,1.042 0.167,0.177 10 false 16 4.385,2.052 4.635,2.229 0.25,0.177 10 false 11 4.667,2.146 5,2.323 0.333,0.177 10 false E 4.656,0.979 4.99,1.156 0.333,0.177 10 false SW1 4.281,2.958 4.531,3.135 0.25,0.177 10 false G7 4.542,2.958 6.594,3.219 2.052,0.26 10 false Combination Meter Mirror ECU

PROCEDURE

1.READ VALUE USING GTS (MAIN SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Head Up Display / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Head Up Display > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch Headup display switch OFF or ON OFF: Switch released
ON: Switch pushed
-
Body Electrical > Head Up Display > Data List
Tester Display
Main Switch
50003 390 2
OK:

Headup display switch condition displayed on the GTS changes with the actual switch operation.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER MIRROR ECU

NG

2.INSPECT HEADUP DISPLAY SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY)
2.INSPECT HEADUP DISPLAY SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY)
a.

Remove the headup display switch (No. 2 combination switch assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SWITCH>REMOVAL


b.

Inspect the headup display switch (No. 2 combination switch assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - HEADUP DISPLAY SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY))

NG

REPLACE HEADUP DISPLAY SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - HEADUP DISPLAY SWITCH (NO. 2 COMBINATION SWITCH ASSEMBLY))
a.

Disconnect the G7 combination meter mirror ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-16 (SW1) - F49-3 (ILU) Always Below 1 Ω
G7-11 (E) - F49-10 (E) Always Below 1 Ω
G7-16 (SW1) or F49-3 (ILU) - Body ground Always 10 kΩ or higher
G7-11 (E) or F49-10 (E) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER MIRROR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR