Home › Engine / Hybrid System › 2ZR-FXE FUEL › FUEL PUMP(w/o Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047496 2ZR-FXE FUEL _0241961 FUEL PUMP(w/o Canister Pump Module) A

2ZR-FXE FUEL  FUEL PUMP(w/o Canister Pump Module)  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Install a new fuel suction tube set gasket to the fuel tank assembly.


b.

Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



c.
A374369C02
1.188,1.406 0.813,0.438 0.813,0.438 2.146,0.75 true 0.292,2.719 0.917,2.719 true 0.635,0.354 0.948,0.51 0.313,0.156 10 false *a 0.115,2.646 0.427,2.802 0.313,0.156 10 false *a
*a Protrusion
V100135

Notch


Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches in the fuel tank assembly.


Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.

Install the fuel pump gauge retainer.

i.

While pressing down on the fuel suction tube with pump and gauge assembly, temporarily install the fuel pump gauge retainer.


ii.
A374358C03
0.76,0.75 1.188,0.75 true 0.781,0.365 1.292,0.365 true 2.344,0.906 2.615,0.563 2.615,0.563 2.729,0.563 true 2.563,1.177 2.771,1.573 2.771,1.573 2.865,1.573 true 2.229,2.063 2.229,1.365 true 0.948,2.938 1.771,2.938 true 1.833,2.875 2.146,3.031 0.313,0.156 10 false *a 2.927,1.521 3.24,1.677 0.313,0.156 10 false *b 2.146,2.083 2.458,2.24 0.313,0.156 10 false *c 0.604,0.302 0.917,0.458 0.313,0.156 10 false *d 0.583,0.677 0.896,0.833 0.313,0.156 10 false *c 2.792,0.5 3.104,0.656 0.313,0.156 10 false *d
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-14030  (09808-01030, 09808-01050)
09808-01071  

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



iii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iv.
A374370C02
1.448,0.302 1.604,0.302 1.604,0.302 1.875,0.854 false 0.521,3.438 0.677,3.438 0.677,3.438 0.885,4.052 true 1.146,3.906 1.448,3.552 1.448,3.552 1.583,3.552 true 2.083,2.25 2.083,1.667 true 0.99,0.646 1.146,0.646 1.146,0.646 1.292,0.917 false 1.073,0.99 1.438,0.99 true 2.167,1.354 2.531,1.354 true 1.115,1.24 1.385,1.24 true 1.615,3.479 1.792,3.635 0.177,0.156 10 true *a 0.313,3.365 0.5,3.531 0.188,0.167 10 true *b 1.292,0.208 1.604,0.365 0.313,0.156 10 false *c 0.823,0.563 1.135,0.719 0.313,0.156 10 false *d 2.01,2.271 2.229,2.427 0.219,0.156 10 false *e 0.938,0.906 1.25,1.063 0.313,0.156 10 false *f 2.573,1.281 2.74,1.438 0.167,0.156 10 true *f 0.948,1.146 1.167,1.302 0.219,0.156 10 false *e
*a Triangle Mark (Fuel Pump Gauge Retainer)
*b Triangle Mark (Fuel Tank Assembly)
*c SST (Handle)
*d SST (Plate)
*e SST (Claw)
*f SST (Bolt)
V100136

Front Side


Install SST (handle) to SST (plate).

SST
09808-14030  (09808-01010, 09808-01030, 09808-01050)
09808-01071  


v.

Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer are aligned with the triangle mark on the fuel tank assembly to install the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

·

Make sure that the fuel suction tube set gasket does not come off.





b.

Engage the claw to install the No. 1 fuel tube clamp.


Hide 77209F 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

A374371C02
3.635,1.51 4.948,2.688 1.313,1.177 5.302,1.5 6.615,2.677 1.313,1.177 1.531,0.313 1.646,0.313 1.646,0.313 1.813,1 true 1.573,2.26 1.573,1.979 true 4.625,1.052 4.719,1.052 4.719,1.052 4.813,0.781 false 5.323,0.771 5.771,0.771 5.771,0.771 5.771,0.885 false 5.531,0.604 5.781,0.604 false 5.313,0.885 5.844,0.885 false 4.469,1.885 4.656,1.885 false 4.594,2.438 4.469,2.438 4.469,2.438 4.26,2 true 5.885,1.927 6.104,1.635 6.104,1.635 6.198,1.635 true 6.104,1.958 6.302,1.958 false 4.844,0.323 5.031,0.323 false 4.448,0.99 4.76,1.146 0.313,0.156 10 false *1 5.833,0.531 6.146,0.688 0.313,0.156 10 false *2 1.365,0.25 1.677,0.406 0.313,0.156 10 false *3 4.688,0.24 5,0.396 0.313,0.156 10 false *a 5.896,0.823 6.208,0.979 0.313,0.156 10 false *b 3.698,1.542 4.01,1.698 0.313,0.156 10 false *c 4.646,2.365 4.958,2.521 0.313,0.156 10 false *e 1.479,2.292 1.792,2.448 0.313,0.156 10 false *2 4.708,1.813 5.021,1.969 0.313,0.156 10 false *2 6.354,1.896 6.667,2.052 0.313,0.156 10 false *2 6.24,1.563 6.552,1.719 0.313,0.156 10 false *e 5.354,1.531 5.667,1.688 0.313,0.156 10 false *d
*1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly - -
*a Fuel Tube Joint *b O-ring
*c Correct *d Incorrect
*e Collar - -
V100135

Insert
V100136

Insert


NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint as shown in the illustration.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 77754B 4.CONNECT CHARCOAL CANISTER OUTLET HOSE

a.

Connect the charcoal canister outlet hose to the fuel suction tube with pump and gauge assembly.


Hide 77026A 5.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A374354C02
1.604,2.083 1.823,2.24 0.219,0.156 10 true *a 2.281,2.677 2.594,2.833 0.313,0.156 10 false *b
*a Up
*b 120°


Connect the No. 1 fuel evaporation tube sub-assembly to the fuel suction tube with pump and gauge assembly and slide the clip to secure it.

HINT:

Engage the clip within the area shown in the illustration.



Hide 58325E 6.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


b.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


c.

Connect the fuel pump connector.


d.

Install the rear floor service hole cover with new butyl tape.


Hide 82818B 7.INSTALL NO. 3 WIRING HARNESS PROTECTOR

a.

Install a new No. 3 wiring harness protector to the rear floor service hole cover.


Hide 71305A 8.INSTALL CENTER REAR SEATBACK HINGE SUB-ASSEMBLY

a.

Install the center rear seatback hinge sub-assembly to the vehicle body with the 2 bolts.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 10.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12.INSTALL REAR SEAT ASSEMBLY

Hide 64995 13.INSTALL DECK FLOOR BOX RH (w/o Spare Tire)

Hide 64997 14.INSTALL DECK FLOOR BOX LH (w/o Spare Tire)

Hide 64995 15.INSTALL DECK FLOOR BOX RH (w/ Compact Spare Tire)

Hide 64997 16.INSTALL DECK FLOOR BOX LH (w/ Compact Spare Tire)

Hide 64993 17.INSTALL REAR DECK FLOOR BOX (w/ Compact Spare Tire)

Hide 64997 18.INSTALL DECK FLOOR BOX LH (w/ Full Size Spare Tire)

Hide 64995 19.INSTALL DECK FLOOR BOX RH (w/ Full Size Spare Tire)

Hide 58432D 20.INSTALL DECK BOARD RETAINER

Hide 58415E 21.INSTALL REAR NO. 1 FLOOR BOARD

Hide 22.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump with filter assembly.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION