Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING
RM3210E _58 Vehicle Interior _047504 INTERIOR PANELS / TRIM _0242015 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


PROCEDURE

Hide 1.INSTALL ROOF HEADLINING ASSEMBLY

a.
B433819C01
0,0 0,0 false
V113147

Install in this Direction


Put the roof headlining assembly back into the vehicle through the back door as shown in the illustration.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.



b.

for Roof Side (w/o Sliding Roof):

B433841C01
1.281,2.563 1.563,2.844 0.281,0.281 12 true *A
*A w/ Television Antenna - -


i.

Install the roof headlining assembly with the 3 clips.


ii.

w/ Television Antenna:

1.

Connect the connector.




c.

for Roof Side (w/ Sliding Roof):

B433842C01
3.042,2.198 3.042,1.823 true 2.875,1.521 2.521,1.229 2.521,1.229 3.094,1.458 true 3.76,2 4.281,2.24 4.281,2.24 3.948,1.958 true 4.052,1.719 4.219,1.427 4.219,1.427 3.729,1.51 true 1.302,3.542 1.302,3.292 true 2.365,1.146 2.677,1.302 0.313,0.156 10 false *a 2.958,2.208 3.198,2.385 0.24,0.177 10 true *b 4.292,2.167 4.51,2.354 0.219,0.188 10 true *a 4.25,1.313 4.469,1.5 0.219,0.188 10 true *a 1.229,3.531 1.469,3.708 0.24,0.177 10 true *c
*a Fastener *b Guide
*c Clamp - -


i.

Engage the guide and 6 fasteners.


ii.

Install the roof headlining assembly with the 3 clips.


iii.

Connect each connector.


iv.

Engage the clamp.



d.

for Rear Pillar RH Side:

i.

Connect the 2 connectors.



e.

for Front Pillar LH Side:

i.

Remove the protective cover.


ii.

Connect the 2 connectors.


iii.

Engage the 4 clamps.


iv.

Install the protective cover.



f.

for Front Pillar RH Side:

i.

Remove the protective cover.


ii.

Connect each connector.


iii.

Engage the 3 clamps.


iv.

Install the protective cover.



g.

for Windshield Glass Side:

i.

Connect each connector.



Hide 74348C 2.INSTALL VISOR HOLDER LH

a.
B438441

Engage the 2 claws.


b.
B438442C02
0,0 0,0 false
V113147

Install in this Direction


Push in the visor holder as shown in the illustration.


Hide 74320 3.INSTALL VISOR ASSEMBLY LH

a.
B433796C01
1.958,0.396 2.365,0.51 true 1.75,0.292 1.948,0.49 0.198,0.198 10 true *1
*1 Visor Holder


Connect the visor assembly LH to the visor holder.


b.

Install the visor assembly LH with the 2 screws.


Hide 74325 4.INSTALL VISOR BRACKET COVER (for LH Side)

a.
B433798C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws to install the visor bracket cover as shown in the illustration.


Hide 74348B 5.INSTALL VISOR HOLDER RH

HINT:

Use the same procedure as for the LH side.


Hide 74310 6.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74325 7.INSTALL VISOR BRACKET COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 8.INSTALL ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure for the RH side and LH side.


a.
B429653

Install the 2 clips to the assist grip.


b.

Temporarily install the 2 assist grip covers to the assist grip as shown in the illustration.


c.
B433800C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 clips to install the assist grip assembly as shown in the illustration.


d.
B433802

Engage the 2 claws to install the assist grip cover LH.

NOTICE:

Make sure that the clip is engaged securely.


HINT:

Use the same procedure for the RH side and LH side.



Hide 74630E 9.INSTALL REAR ASSIST GRIP ASSEMBLY LH

HINT:

Use the same procedure as for the assist grip assembly.


Hide 74620C 10.INSTALL REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure as for the assist grip assembly.


Hide 86466D 11.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense)

Hide 86466E 12.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense)

Hide 87834 13.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Inner Rear View Mirror Stay Holder Cover)

Hide 89941 14.INSTALL RAIN SENSOR (w/ Rain Sensor)

Hide 89943 15.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

Hide 81240 16.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Hide 17.INSTALL ROOF CONSOLE BOX ASSEMBLY

Hide 62480A 18.INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH

a.

Engage the 5 clips to install the roof side inner garnish assembly LH as shown in the illustration.

B433776C01
0,0 0,0 false
V113147

Install in this Direction - -



Hide 64740C 19.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

a.

When reusing the deck trim side panel assembly LH:

i.
B433771C02
1.021,0.438 1.583,0.583 true 0.792,0.344 1.01,0.542 0.219,0.198 10 true *1
*1 No. 2 Luggage Compartment Trim Hook
V113147

Turn in this Direction (1)
V113148

Remove in this Direction (2)


Remove the clip from the No. 2 luggage compartment trim hook as shown in the illustration.


ii.
B439364C02
2.5,0.396 3.021,0.26 true 3.042,0.177 3.354,0.333 0.313,0.156 10 false *1
*1 Clip Piece
V113146

Insert Screwdriver Here
V113147

Insert in this Direction


Using a screwdriver, push out the clip piece.

HINT:

Make sure that the clip piece are positioned as shown in the illustration.



iii.
B433773C02
1.25,0.24 1.719,0.354 true 1.042,0.156 1.24,0.344 0.198,0.188 10 true *1
*1 No. 2 Luggage Compartment Trim Hook
V113147

Install in this Direction (1)
V113148

Turn in this Direction (2)


Install the clip to the No. 2 luggage compartment trim hook as shown in the illustration.



b.

Engage the guide, 5 claws and 3 clips.

B433783C01
0,0 0,0 false
V113147

Install in this Direction - -



c.

Install the deck trim side panel assembly LH with the 2 screws.


Hide 81330 20.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Hide 64937A 21.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (for LH Side)

a.
B431798C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the No. 1 tonneau cover holder cap as shown in the illustration.


Hide 64938 22.INSTALL TONNEAU COVER HOOK A (for LH Side)

a.
B434641C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the tonneau cover hook A as shown in the illustration.


Hide 58460D 23.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)

a.

Engage the guide.


b.

Install the luggage hold belt striker assembly with the bolt.


Hide 62552F 24.INSTALL REAR SEAT SIDE GARNISH LH

a.
B431789C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides, claw and 2 clips to install the rear seat side garnish LH as shown in the illustration.


Hide 71304C 25.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH

a.

Install the rear seatback hinge sub-assembly LH with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 76974F 26.INSTALL REAR UNDER SIDE COVER LH

a.
B437815C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide, claw and 4 clips as shown in the illustration.


b.

Install the rear under side cover LH with the 2 clips.


Hide 62470A 27.INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 64730B 28.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 64937A 29.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 64938 30.INSTALL TONNEAU COVER HOOK A (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 58460D 31.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 62551F 32.INSTALL REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 71303C 33.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 76973F 34.INSTALL REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 35.INSTALL REAR SEAT ASSEMBLY

Hide 62420A 36.INSTALL CENTER PILLAR GARNISH ASSEMBLY LH

a.
B431781C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 guides and clip as shown in the illustration.


b.

Install the center pillar garnish assembly LH with the 2 clips.


Hide 62414A 37.INSTALL LOWER CENTER PILLAR GARNISH LH

a.
B431773C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws and 3 clips to install the lower center pillar garnish LH as shown in the illustration.


Hide 73220 38.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 73233 39.INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

Hide 62332A 40.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 67918A 41.INSTALL REAR DOOR SCUFF PLATE LH

a.
B431767C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 guides and 7 claws to install the rear door scuff plate LH as shown in the illustration.


Hide 62212 42.INSTALL FRONT PILLAR GARNISH LH

a.

Remove the protective cover.


b.

Engage the front pillar garnish clip to the front pillar garnish LH.

HINT:

Install the front pillar garnish clip so that it is oriented as shown in the illustration.


B437818C02
1.646,0.521 1.979,0.521 true 1.823,1.052 2.156,1.052 true 2,0.438 2.313,0.594 0.313,0.156 10 false *1 2.177,0.969 2.49,1.125 0.313,0.156 10 false *2 1.5,0.083 1.813,0.24 0.313,0.156 10 false *a 3.5,0.094 3.813,0.25 0.313,0.156 10 false *b 5.667,0.094 5.979,0.25 0.313,0.156 10 false *b
*1 Front Pillar Garnish Clip *2 Front Pillar Garnish LH
*a Correct *b Incorrect



c.
B431755C01
0,0 0,0 false
V113147

Install in this Direction


Push the front pillar garnish LH as shown in the illustration to engage the 2 guides.


d.
B431749C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clip and front pillar garnish clip to install the front pillar garnish LH as shown in the illustration.

HINT:

Make sure that the curtain shield airbag assembly LH is not pinched.



Hide 62312B 43.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62112 44.INSTALL COWL SIDE TRIM BOARD LH

a.
B431743C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 clips as shown in the illustration.


b.

Install the cowl side trim board LH with the clip.


Hide 67914 45.INSTALL FRONT DOOR SCUFF PLATE LH

a.
B431739C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and 8 claws to install the front door scuff plate LH as shown in the illustration.


Hide 62410A 46.INSTALL CENTER PILLAR GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62413A 47.INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73210 48.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 49.INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 62331A 50.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 67917A 51.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62211 52.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 53.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62111C 54.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 67913 55.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 64716D 56.INSTALL REAR DECK TRIM COVER

a.
B431733C02
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and 4 clips to install the rear deck trim cover as shown in the illustration.


Hide 58460D 57.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Rear Side)

a.

Engage the 2 guides.


b.

Install the 2 luggage hold belt striker assemblies with the 2 bolts.


Hide 64718D 58.INSTALL DECK TRIM SERVICE HOLE COVER

Hide 64995 59.INSTALL DECK FLOOR BOX RH (w/o Spare Tire)

a.
B434639C02
0,0 0,0 false
V113147

Install in this Direction


Engage the clip to install the deck floor box RH as shown in the illustration.


Hide 64997 60.INSTALL DECK FLOOR BOX LH (w/o Spare Tire)

a.
B439345C02
0,0 0,0 false
V113147

Install in this Direction


Engage the clip to install the deck floor box LH as shown in the illustration.


Hide 64995 61.INSTALL DECK FLOOR BOX RH (w/ Compact Spare Tire)

a.
B439344C02
0,0 0,0 false
V113147

Install in this Direction


Engage the clip to install the deck floor box RH as shown in the illustration.


Hide 64997 62.INSTALL DECK FLOOR BOX LH (w/ Compact Spare Tire)

a.
B439346C02
0,0 0,0 false
V113147

Install in this Direction


Engage the clip to install the deck floor box LH as shown in the illustration.


Hide 64993 63.INSTALL REAR DECK FLOOR BOX (w/ Compact Spare Tire)

a.

Install the rear deck floor box.


Hide 64997 64.INSTALL DECK FLOOR BOX LH (w/ Full Size Spare Tire)

a.
B438447C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clip to install the deck floor box LH as shown in the illustration.


Hide 64995 65.INSTALL DECK FLOOR BOX RH (w/ Full Size Spare Tire)

a.
B438446C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clip to install the deck floor box RH as shown in the illustration.


Hide 58432D 66.INSTALL DECK BOARD RETAINER

a.
B431727C02
0,0 0,0 false
V113147

Install in this Direction


for LH Side:

i.

Engage the guide and clip to install the deck board retainer as shown in the illustration.



b.
B439096C03
0,0 0,0 false
V113147

Install in this Direction


for RH Side:

i.

Engage the guide and clip to install the deck board retainer as shown in the illustration.



Hide 58415E 67.INSTALL REAR NO. 1 FLOOR BOARD

a.

Install the rear No. 1 floor board.


Hide 64910J 68.INSTALL TONNEAU COVER ASSEMBLY

a.

Install the tonneau cover assembly.