Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function)
RM3210E _58 Vehicle Interior _047507 THEFT DETERRENT / KEYLESS ENTRY _0242212 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2275  STSW Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction is detected in the starter circuit inside the certification ECU (smart key ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2275 STSW Monitor Malfunction Certification ECU (smart key ECU assembly) internal HV activation request output circuit malfunction or external circuit malfunction (1-trip detection logic*)
·

AM2 fuse

·

Certification ECU (smart key ECU assembly)

·

Hybrid vehicle control ECU

·

Wire harness or connector


DTC Output Confirmation Operation:

Turn the power switch on (IG) and wait 10 seconds or more, then start the hybrid control system 3 times.



*: Only detected while a malfunction is present and the power switch is on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

The power source mode changes to on (READY) even though the hybrid control system is not started.

·

The power source mode does not change to on (READY) even though the hybrid control system is started.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2275
Power Source Control
·

Starter Request Signal



WIRING DIAGRAM

B427518E06
1.26,1.073 1.667,1.271 0.406,0.198 10 false ST2 1.625,1.073 2.031,1.271 0.406,0.198 10 false 4 2.031,0.51 3.656,0.917 1.625,0.406 10 false from Auxiliary Battery 4.26,0.667 4.667,0.865 0.406,0.198 10 false AM2 5.094,0.417 5.5,0.615 0.406,0.198 10 false 4 5.021,1.052 5.427,1.25 0.406,0.198 10 false 27 5.281,0.531 5.688,0.729 0.406,0.198 10 false +B 6.208,1.313 6.615,1.51 0.406,0.198 10 false IC 5.281,2.177 5.688,2.375 0.406,0.198 10 false E 5.042,2.073 5.448,2.271 0.406,0.198 10 false 18 5.208,2.688 5.615,2.885 0.406,0.198 10 false F1 5.208,2.854 6.75,3.344 1.542,0.49 10 false Certification ECU (Smart Key ECU Assembly) 0.5,2.667 0.906,2.865 0.406,0.198 10 false F3 0.5,2.823 2.281,3.188 1.781,0.365 10 false Hybrid Vehicle Control ECU 5.281,1.063 5.688,1.26 0.406,0.198 10 false ST2 5.75,0.708 6.156,0.906 0.406,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the hybrid vehicle control ECU or certification ECU (smart key ECU assembly), refer to entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F3 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-27 (ST2) - F3-4 (ST2) Always Below 1 Ω
F1-27 (ST2) or F3-4 (ST2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the F3 hybrid vehicle control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F1-27 (ST2) - Body ground With the brake pedal depressed, the power switch is pressed and held → After approx. 3 sec. has elapsed, the power switch is released 8.5 V or higher → 1 V or less



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)