Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM
RM3210E _58 Vehicle Interior _047513 DOOR LOCK _0242297 WIRELESS DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). (ex. If a door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1242 Wireless Door Lock Tuner Circuit Malfunction
·

Short to ground in RDAM terminal circuit between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short to ground in RDAM terminal circuit when voltage (5 V) is not being output from terminal RCO


·

Wire harness or connector

·

Door control receiver

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

for 12 Pin Type


B440789E02
1.146,0.844 1.76,1.042 0.615,0.198 10 false DATA 1.354,1.646 1.969,1.844 0.615,0.198 10 false +5 1.229,2.344 1.844,2.542 0.615,0.198 10 false GND 1.656,0.76 2.271,0.958 0.615,0.198 10 false 9 1.635,2.229 2.25,2.427 0.615,0.198 10 false 12 1.625,1.542 2.24,1.74 0.615,0.198 10 false 10 0.333,2.833 0.948,3.031 0.615,0.198 10 false M23 0.333,3 2.969,3.375 2.635,0.375 10 false Electrical Key and Tire Pressure Monitoring System Receiver Assembly 4.969,2.833 7.094,3.198 2.125,0.365 10 false Certification ECU (Smart Key ECU Assembly) 5.74,0.854 6.354,1.052 0.615,0.198 10 false RDAM 5.75,2.365 6.365,2.563 0.615,0.198 10 false E 5.74,1.656 6.354,1.854 0.615,0.198 10 false RCO 5.365,0.854 5.979,1.052 0.615,0.198 10 false M59 5.365,1.646 5.979,1.844 0.615,0.198 10 false M59 5.417,2.344 6.031,2.542 0.615,0.198 10 false F1 5.406,0.646 6.021,0.844 0.615,0.198 10 false 19 5.396,1.448 6.01,1.646 0.615,0.198 10 false 18 5.396,2.135 6.01,2.333 0.615,0.198 10 false 18


for 5 Pin Type


B440789E03
1.146,0.844 1.76,1.042 0.615,0.198 10 false DATA 1.354,1.646 1.969,1.844 0.615,0.198 10 false +5 1.229,2.344 1.844,2.542 0.615,0.198 10 false GND 1.656,0.76 2.271,0.958 0.615,0.198 10 false 5 1.656,2.229 2.271,2.427 0.615,0.198 10 false 1 1.656,1.542 2.271,1.74 0.615,0.198 10 false 4 0.333,2.833 0.948,3.031 0.615,0.198 10 false M14 0.333,3 2.969,3.375 2.635,0.375 10 false Smart Door Control Receiver Assembly 4.969,2.833 7.094,3.198 2.125,0.365 10 false Certification ECU (Smart Key ECU Assembly) 5.74,0.854 6.354,1.052 0.615,0.198 10 false RDAM 5.75,2.365 6.365,2.563 0.615,0.198 10 false E 5.74,1.656 6.354,1.854 0.615,0.198 10 false RCO 5.365,0.854 5.979,1.052 0.615,0.198 10 false M59 5.365,1.646 5.979,1.844 0.615,0.198 10 false M59 5.417,2.344 6.031,2.542 0.615,0.198 10 false F1 5.406,0.646 6.021,0.844 0.615,0.198 10 false 19 5.396,1.448 6.01,1.646 0.615,0.198 10 false 18 5.396,2.135 6.01,2.333 0.615,0.198 10 false 18


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, the performance of the entry function and wireless function may be affected.

·

This DTC is not stored within 10 seconds of the power switch being turned from on (IG) to off.

·

The wireless door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication system is functioning properly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.*

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

*: for 12 Pin Type


·

It is necessary to perform initialization (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the door control receiver if the door control receiver has been replaced.*

Click here

*: for 12 Pin Type




PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the M23*1 or M14*2 door control receiver connector.

*1: for 12 Pin Type

*2: for 5 Pin Type


B440788C02
3.198,0.396 3.604,0.635 0.406,0.24 4.521,0.427 4.927,0.667 0.406,0.24 4.115,2.583 3.979,2.583 3.979,2.583 3.813,1.448 false 4.896,2.594 4.76,2.594 4.76,2.594 3.906,1.438 false 5.688,2.25 5.552,2.25 5.552,2.25 5.208,1.448 false 3.271,0.438 3.729,0.635 0.458,0.198 10 false M59 4.635,0.469 5.094,0.667 0.458,0.198 10 false F1 4.958,2.51 5.573,2.708 0.615,0.198 10 false RCO 4.177,2.51 4.792,2.708 0.615,0.198 10 false RDAM 5.75,2.177 6.365,2.375 0.615,0.198 10 false E
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



b.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M59-19 (RDAM) - F1-18 (E) Power switch off 11 to 14 V
M59-18 (RCO) - F1-18 (E) always Below 1 V → 4.5 to 5.5 V pulse generation at regular intervals


Standard Resistance:
Tester Connection Condition Specified Condition
F1-18 (E) - Body ground Always Below 1 Ω



Result:
Result Proceed to
NG A
OK (for 12 Pin Type) B
OK (for 5 Pin Type) C



A

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

REPLACE ELECTRICAL KEY AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

C

REPLACE SMART DOOR CONTROL RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F1 and M59 certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M59-19 (RDAM) - M23-9 (DATA)*1
M59-19 (RDAM) - M14-5 (DATA)*2
Always Below 1 Ω
M59-18 (RCO) - M23-10 (+5)*1
M59-18 (RCO) - M14-4 (+5)*2
Always Below 1 Ω
M23-12 (GND) - Body ground*1
M14-1 (GND) - Body ground*2
Always Below 1 Ω
M23-9 (DATA) or M59-19 (RDAM) - Body ground*1
M14-5 (DATA) or M59-19 (RDAM) - Body ground*2
Always 10 kΩ or higher
M23-10 (+5) or M59-18 (RCO) - Body ground*1
M14-4 (+5) or M59-18 (RCO) - Body ground*2
Always 10 kΩ or higher


*1: for 12 Pin Type

*2: for 5 Pin Type



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR