The torque sensor converts the rotational torque received from the steering wheel into electric signals and sends them to the power steering ECU assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Return-to-normal Condition | Note |
|---|---|---|---|---|---|---|
| C1511 | Torque Sensor1 | Torque sensor malfunction | ·
Torque sensor (Electric power steering column sub-assembly) ·
Power steering ECU assembly |
EPS warning light: Comes on | The ECU judges the system has returned to normal or the power switch is turned on (IG) again | - |
| C1512 | Torque Sensor2 | Torque sensor malfunction | ·
Torque sensor (Electric power steering column sub-assembly) ·
Power steering ECU assembly |
EPS warning light: Comes on | The ECU judges the system has returned to normal or the power switch is turned on (IG) again | - |
| C1513 | Torque Sensor Deviation Excessive | Torque sensor malfunction | ·
Torque sensor (Electric power steering column sub-assembly) ·
Power steering ECU assembly |
EPS warning light: Comes on | The ECU judges the system has returned to normal or the power switch is turned on (IG) again | - |
| C1514 | Torque Sensor Power Supply Voltage | Torque sensor malfunction | ·
Torque sensor (Electric power steering column sub-assembly) ·
Power steering ECU assembly |
EPS warning light: Comes on | Power switch on (IG) again | - |
| C1517 | Torque Hold | Torque sensor malfunction | ·
Torque sensor (Electric power steering column sub-assembly) ·
Power steering ECU assembly |
EPS warning light: Comes on | Power switch on (IG) again | - |
If the electric power steering column sub-assembly has been replaced, perform torque sensor zero point calibration.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
Check the connection condition of the torque sensor connector.
Torque sensor connector is securely connected to the power steering ECU assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Power Steering ECU Assembly) |
Turn the power switch to on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z17-7 (TRQV1) - z17-8 (TRQG1) | power switch on (IG) | 4.5 to 5.5 V |
| z17-3 (TRQV2) - z17-2 (TRQG2) | power switch on (IG) | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING ECU(for LHD)>REMOVAL
for RHD: Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING ECU(for RHD)>REMOVAL
| *a | Component with harness connected
(Power Steering ECU Assembly) |
Turn the power switch on (READY).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z17-9 (TRQ1) - z17-8 (TRQG1) | Power switch on (READY) and steering wheel not being turned (without load) | 2.3 to 2.7 V |
| Power switch on (READY) and steering wheel being turned to the right with vehicle stopped | 2.5 to 3.8 V | |
| Power switch on (READY) and steering wheel being turned to the left with vehicle stopped | 1.2 to 2.5 V | |
| z17-1 (TRQ2) - z17-2 (TRQG2) | Power switch on (READY) and steering wheel not being turned (without load) | 2.3 to 2.7 V |
| Power switch on (READY) and steering wheel being turned to the right with vehicle stopped | 1.2 to 2.5 V | |
| Power switch on (READY) and steering wheel being turned to the left with vehicle stopped | 2.5 to 3.8 V |
Under each condition, measure the voltage at terminals TRQ1 and TRQ2, and calculate the sum.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Sum of voltage between z17-9 (TRQ1) and z17-8 (TRQG1) and voltage between z17-1 (TRQ2) and z17-2 (TRQG2) | Power switch on (READY) and steering wheel not being turned (without load) | Between 4.75 V and 5.25 V |
| Power switch on (READY) and steering wheel being turned to the right with vehicle stopped | ||
| Power switch on (READY) and steering wheel being turned to the left with vehicle stopped |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING ECU(for LHD)>REMOVAL
for RHD: Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING ECU(for RHD)>REMOVAL
NG