Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM3210E _55 Steering _047548 STEERING COLUMN _0242570 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the electric power steering column sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Electric power steering column sub-assembly Torque sensor zero point calibration
·

DTCs are stored

·

EPS warning light illuminates


(Click here)

PROCEDURE

Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45130 3.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 45024 5.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY

NOTICE:

Removing the lower steering column cover sub-assembly in the incorrect order will cause the parts to break.


a.

Release the tilt and telescopic lever and fully extend and lower the steering column assembly.


b.

Lock the tilt and telescopic lever.


c.
C346833

Remove the 2 screws.


d.
C346876C01
0,0 0,0 false
V100135

Push


Push the upper steering column cover and disengage the 2 claws as shown in the illustration.


e.
C346877

Disengage the 2 claws.


f.

Release the tilt and telescopic lever and fully extend and lift the steering column assembly.


g.

Lock the tilt and telescopic lever.


h.
C346878C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Pull the lower steering column cover sub-assembly toward the rear of the vehicle to disengage the claw and remove the lower steering column cover sub-assembly.


Hide 45286B 6.REMOVE UPPER STEERING COLUMN COVER

a.

Release the tilt and telescopic lever and fully extend and lower the steering column assembly.


b.

Lock the tilt and telescopic lever.


c.
C346835

Disengage the claw and separate the upper steering column cover.


d.
C346836

Disengage the 2 claws and 4 clips to remove the upper steering column cover.


Hide 7.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed with the auxiliary battery connected and the power switch on (IG).

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.

Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.


b.
C346838

Disengage the 3 claws to remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.


Hide 73900 8.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 9.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 55406B 10.REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Hide 58816C 11.REMOVE FRONT NO. 1 CONSOLE BOX INSERT

Hide 87211 12.REMOVE NO. 1 AIR DUCT (for LHD)

a.
C346839

Remove the 2 bolts.


b.

Disengage the 3 claws to remove the No. 1 air duct.


Hide 55362C 13.REMOVE PARKING BRAKE MOUNTING BRACKET (for RHD)

a.
C345179C01
1.448,0.885 2.156,0.885 true 1.917,1.292 2.771,1.292 true 2.188,0.813 2.5,0.969 0.313,0.156 10 true *a 2.813,1.229 3.125,1.385 0.313,0.156 10 true *b
*a Bolt
*b Screw


Remove the bolt, screw and parking brake mounting bracket.


Hide 87211A 14.REMOVE NO. 2 AIR DUCT (for RHD)

a.
C345180

Remove the bolt.


b.

Disengage the 3 claws to remove the No. 2 air duct.


Hide 84340 15.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 45259A 16.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
C346840

Disengage the claw and open the column hole cover silencer sheet.


b.
C346842C01
0,0 0,0 false
V113146

Place Hand Here


Disengage the 2 claws to remove the column hole cover silencer sheet.


Hide 45260 17.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C346843C01
1.771,1.25 2.24,1.25 2.24,1.25 2.24,1.76 true 1.802,1.302 2.24,1.302 true 2.177,1.771 2.417,1.979 0.24,0.208 10 true *a
*a Matchmark
V113147

Separate in this direction


Put matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.


b.

Remove the bolt.


c.

Separate the No. 2 steering intermediate shaft assembly from the steering gear assembly.


Hide 45260 18.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C346845C01
1.333,0.802 1.333,0.51 1.333,0.51 0.385,0.51 true 1.229,0.76 1.229,0.521 true 0.198,0.417 0.406,0.604 0.208,0.188 10 true *a
*a Matchmark
V113147

Remove in this direction


Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.


b.

Remove the bolt.


c.

Remove the No. 2 steering intermediate shaft assembly from the steering column assembly.


Hide 19.REMOVE STEERING COLUMN ASSEMBLY (for LHD)

a.
C346847

Disconnect the 2 connectors.


b.

Disengage the clamp.


c.

Disconnect each connector and disengage each clamp from the steering column assembly.


d.
C346848

Remove the bolt, 2 nuts and steering column assembly.


Hide 20.REMOVE STEERING COLUMN ASSEMBLY (for RHD)

a.
C345181

Disconnect the 2 connectors.


b.

Disengage the clamp.


c.

Disconnect each connector and disengage each clamp from the steering column assembly.


d.
C345182

Remove the bolt, 2 nuts and steering column assembly.