Refer to DTC P059F73.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P059F73
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P05A27E | Active Grille Air Shutter "A" Actuator Stuck On | The following condition is met and the ECM receives a malfunction signal 17 times* (2 trip detection logic):
·
Grille shutter opening operation is performed for 11 seconds or more and the ECM receives a malfunction signal once or more. |
·
Radiator shutter sub-assembly ·
Swing grille actuator assembly |
Comes on | DTC stored | SAE Code: P05A3 |
| P05A27F | Active Grille Air Shutter "A" Actuator Stuck Off | The following condition is met and the ECM receives a malfunction signal 17 times* (2 trip detection logic):
·
Grille shutter closing operation is performed for 11 seconds or more and the ECM receives a malfunction signal once or more. |
·
Radiator shutter sub-assembly ·
Swing grille actuator assembly |
Comes on | DTC stored | SAE Code: P05A3 |
*: For every 65 ms that the ECM receives a grille shutter system malfunction signal from the grille shutter ECU (swing grille actuator assembly) the ECM determines it has received the signal 1 time. If the ECM determines the malfunction signal has been received 17 consecutive times (the signal is received for approximately 1 second continuously), it will store a DTC.
If the grille shutter ECU (swing grille actuator assembly) detects that the grille shutter motor (swing grille actuator assembly) is performing an open or close operation for longer than the threshold, it will output a malfunction signal to the ECM and the ECM will store a DTC.
| Detection Condition | DTC No. |
|---|---|
| Opening Operation | P05A27E (Active Grille Air Shutter "A" Actuator Stuck On) |
| Closing Operation | P05A27F (Active Grille Air Shutter "A" Actuator Stuck Off) |
| Related DTCs | P05A3: Active grille air shutter performance |
| Required Sensors/Components (Main) | Swing grille actuator assembly
Radiator shutter sub-assembly |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 17 times |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| Auxiliary battery voltage | 10.5 to 16 V |
| Active grille air shutter close control | Operating |
| Monitor runs whenever the following DTCs are not stored | None |
| Auxiliary battery voltage | 10.5 to 16 V |
| Active grille air shutter open control | Operating |
| Following condition is met | 1 time or more |
| Time after active grille air shutter close control is operated | 11 seconds or more |
| Following condition is met | 1 time or more |
| Time after active grille air shutter close control is operated | 11 seconds or more |
| Following condition is met | 1 time or more |
| Time after active grille air shutter open control is operated | 11 seconds or more |
| Following condition is met | 1 time or more |
| Time after active grille air shutter open control is operated | 11 seconds or more |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
"Normal" is displayed.
Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
"Normal" is displayed.
In order to ensure safety, before performing troubleshooting or removing the swing grille actuator assembly or radiator shutter sub-assembly, change the grille shutter control mode to maintenance mode.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.
| Tester Display |
|---|
| Grill Shutter Control Mode Switching |
According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.
| Proceed to |
|---|
| NEXT |
NEXT
Check the area around the shutters and the links of the grille shutter for foreign matter and ice.
No foreign matter or ice.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
| Active Test Display |
|---|
| Shutter Closing Operation Lock Detection |
| Data List Display |
|---|
| Shutter Operation Lock Detection Result for Active Test |
According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
"Normal" is displayed.
Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
| Active Test Display |
|---|
| Shutter Opening Operation Lock Detection |
| Data List Display |
|---|
| Shutter Operation Lock Detection Result for Active Test |
According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
"Normal" is displayed.
When the value of Data List item Shutter Operation Lock Detection Result for Active Test is "Normal", it can be determined that the grille shutter system has returned to normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.
| Tester Display |
|---|
| Grill Shutter Control Mode Switching |
According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.
Check for DTCs and make sure that DTC B1333 is not output.
| Proceed to |
|---|
| NEXT |
NEXT
Remove the radiator shutter sub-assembly.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>REMOVAL
Remove the swing grille actuator assembly.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>DISASSEMBLY
Reconnect the swing grille actuator assembly connector.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection.
| Tester Display |
|---|
| Shutter Closing Operation Lock Detection |
According to the display on the GTS, perform the Active Test and check the operation of the swing grille actuator assembly.
Operation is normal.
Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection.
| Tester Display |
|---|
| Shutter Opening Operation Lock Detection |
According to the display on the GTS, perform the Active Test and check the operation of the swing grille actuator assembly.
Operation is normal.
Perform "Grill Shutter Control Mode Switching and Grill Shutter Initialization" after replacing the swing grille actuator assembly.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the radiator shutter sub-assembly.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>REMOVAL
Remove the swing grille actuator assembly.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>DISASSEMBLY
Manually open and close the radiator shutter sub-assembly and check that it moves smoothly.
Radiator shutter sub-assembly moves smoothly.
Perform "Grill Shutter Control Mode Switching and Grill Shutter Initialization" after replacing the swing grille actuator assembly or radiator shutter sub-assembly.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove any foreign matter and/or ice from the area around the shutters and the links of the grille shutter.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
| Active Test Display |
|---|
| Shutter Closing Operation Lock Detection |
| Data List Display |
|---|
| Shutter Operation Lock Detection Result for Active Test |
According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
"Normal" is displayed.
Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.
| Active Test Display |
|---|
| Shutter Opening Operation Lock Detection |
| Data List Display |
|---|
| Shutter Operation Lock Detection Result for Active Test |
According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.
"Normal" is displayed.
When the value of Data List item Shutter Operation Lock Detection Result for Active Test is "Normal", it can be determined that the grille shutter system has returned to normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.
| Tester Display |
|---|
| Grill Shutter Control Mode Switching |
According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.
Check for DTCs and make sure that DTC B1333 is not output.
| Proceed to |
|---|
| NEXT |
NEXT