Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER
RM3210E _59 Vehicle Exterior _047542 EXTERIOR PANELS / TRIM _0243310 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  REASSEMBLY  


PROCEDURE

Hide 52023 1.INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY

for Reinforcement Type A:

a.
B435258

Install the rear bumper reinforcement sub-assembly with the 8 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 52016A 2.INSTALL REAR BUMPER ARM SUB-ASSEMBLY LH

for Reinforcement Type B:

a.
B436091

Install the rear bumper arm sub-assembly LH with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 52015A 3.INSTALL REAR BUMPER ARM SUB-ASSEMBLY RH

for Reinforcement Type B:

HINT:

Use the same procedure as for the LH side.


Hide 52171A 4.INSTALL NO. 1 REAR BUMPER REINFORCEMENT

for Reinforcement Type B:

a.
B436089

Install the No. 1 rear bumper reinforcement with the 6 bolts.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 52592 5.INSTALL REAR BUMPER SIDE SEAL LH

a.
B435271C01
1.292,2.844 1.833,3.094 true 1.896,3.031 2.208,3.229 0.313,0.198 10 false *1
*1 Rear Bumper Side Clip


Install the 3 clips.


b.

Install the rear bumper side seal LH with the rear bumper side clip.


Hide 52591 6.INSTALL REAR BUMPER SIDE SEAL RH

HINT:

Use the same procedure as for the LH side.


Hide 52576 7.INSTALL REAR BUMPER SIDE RETAINER LH

a.
B435262C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the claw as shown in the illustration.


b.

Engage the guide as shown in the illustration.


c.
B435260C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 clips as shown in the illustration to install the rear bumper side retainer LH.


Hide 52575 8.INSTALL REAR BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 52461M 9.INSTALL NO. 3 REAR BUMPER PAD

HINT:

When installing the No. 3 rear bumper pad, heat the rear bumper assembly using a heat light.


Heating Temperature
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper assembly excessively.


a.

Clean the rear bumper assembly surface.

i.

Using a heat light, heat the rear bumper assembly surface.


ii.

Remove the double-sided tape from the rear bumper assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new No. 3 rear bumper pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B435269C01
1.427,1.552 1.854,1.313 true 1.125,1.49 1.396,1.708 0.271,0.219 10 true *a
*a Line


Install the No. 3 rear bumper pad as shown in the illustration.

HINT:
·

Install the No. 3 rear bumper pad along the line on the rear bumper cover.

·

Use the same procedure for the RH side and LH side.




Hide 52191A 10.INSTALL REAR BUMPER ARM SEAL

HINT:

When installing the rear bumper arm seal, heat the rear bumper assembly using a heat light.


Heating Temperature
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper assembly excessively.


a.

Clean the rear bumper assembly surface.

i.

Using a heat light, heat the rear bumper assembly surface.


ii.

Remove the double-sided tape from the rear bumper assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new rear bumper arm seal.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B435267C01
0.771,1.125 1.26,1.156 true 0.521,1.042 0.76,1.25 0.24,0.208 10 true *a
*a Line


Install the rear bumper arm seal as shown in the illustration.

HINT:
·

Install the rear bumper arm seal along the line on the rear bumper cover.

·

Use the same procedure for the RH side and LH side.




Hide 52461L 11.INSTALL NO. 2 REAR BUMPER PAD

HINT:

When installing the No. 2 rear bumper pad, heat the rear bumper assembly using a heat light.


Heating Temperature
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper assembly excessively.


a.

Clean the rear bumper assembly surface.

i.

Using a heat light, heat the rear bumper assembly surface.


ii.

Remove the double-sided tape from the rear bumper assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new No. 2 rear bumper pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B435265C01
0.917,0.323 1.688,0.625 true 0.688,0.24 0.969,0.458 0.281,0.219 10 true *a
*a Line


Install the No. 2 rear bumper pad as shown in the illustration.

HINT:
·

Install the No. 2 rear bumper pad along the line on the rear bumper cover.

·

Use the same procedure for the RH side and LH side.




Hide 52461K 12.INSTALL NO. 1 REAR BUMPER PAD

HINT:

When installing the No. 1 rear bumper pad, heat the rear bumper assembly using a heat light.


Heating Temperature
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper assembly excessively.


a.

Clean the rear bumper assembly surface.

i.

Using a heat light, heat the rear bumper assembly surface.


ii.

Remove the double-sided tape from the rear bumper assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new No. 1 rear bumper pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B435263C01
1.104,0.604 1.635,0.844 true 0.823,0.5 1.083,0.76 0.26,0.26 10 true *a
*a Line


Install the No. 1 rear bumper pad as shown in the illustration.

HINT:
·

Install the No. 1 rear bumper pad along the line on the rear bumper cover.

·

Use the same procedure for the RH side and LH side.




Hide 52566 13.INSTALL REAR BUMPER EXTENSION FILLER LH (for Type A)

a.
B435257C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and 3 claws as shown in the illustration.


b.
B435255

Install the rear bumper extension filler LH with the 2 clips.


Hide 52566 14.INSTALL REAR BUMPER EXTENSION FILLER LH (for Type B)

a.
B436087C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and 3 claws as shown in the illustration.


b.
B436085

Install the rear bumper extension filler LH with the 2 clips.


Hide 52565 15.INSTALL REAR BUMPER EXTENSION FILLER RH

HINT:

Use the same procedure as for the LH side.


Hide 52453 16.INSTALL CENTER REAR BUMPER GUARD (for Type A)

a.
B435254C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 14 claws as shown in the illustration.


b.
B435252

Install the center rear bumper guard with the 2 screws.


Hide 52453 17.INSTALL CENTER REAR BUMPER GUARD (for Type B)

a.

Engage the 16 claws as shown in the illustration.

B436084C01
0,0 0,0 false
V113147

Install in this Direction - -



b.

Install the 2 clips.

B440957


c.

Install the center rear bumper guard with the 2 screws.

B436082


Hide 52169C 18.INSTALL LOWER REAR BUMPER COVER

a.
B435251C01
0.969,2.49 1.719,2.854 true 1.76,2.792 2.073,2.948 0.313,0.156 10 false *a
*a Hook
V113147

Install in this Direction


Engage the hook.


b.

Engage the 2 claws as shown in the illustration to install the lower rear bumper cover.


Hide 82183 19.INSTALL NO. 3 LUGGAGE ROOM WIRE

a.
B435249

w/o TOYOTA Parking Assist-sensor System:

i.

Engage the 7 clamps to install the No. 3 luggage room wire.



b.
B435248

w/ TOYOTA Parking Assist-sensor System:

i.

Engage the 12 clamps to install the No. 3 luggage room wire.



Hide 81590A 20.INSTALL REAR LIGHT ASSEMBLY LH

Hide 81580D 21.INSTALL REAR LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 89348S 22.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89348R 23.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89348T 24.INSTALL REAR SIDE ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89342A 25.INSTALL REAR CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89342 26.INSTALL REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89342B 27.INSTALL REAR SIDE ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)