Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR(for Rear)
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0243256 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  INSTALLATION  


PROCEDURE

Hide 89348S 1.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

If a rear center ultrasonic sensor retainer has been removed, replace it with a new one.



a.

Clean the surface of the rear bumper cover.

i.

Remove any remaining double-sided tape from the rear bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 30 mm (1.18 in.)


Cover the 2 sensor installation holes with a 30 mm (1.18 in.) circular piece of tape.


c.

Using a brush or felt, apply primer or equivalent to the 2 rear center ultrasonic sensor retainers installation area.

E338237C02
2.896,2.854 3.167,2.656 true 4.125,2.646 4.51,2.854 true 3.219,2.563 3.531,2.76 0.313,0.198 10 true *a 3.917,2.542 4.229,2.74 0.313,0.198 10 true *a
*a Line - -
V100145

Primer - -


NOTICE:
·

Use a clean brush or felt.

·

Do not touch the rear bumper assembly until the primer has dried.




d.

Peel off the release paper from the 2 rear center ultrasonic sensor retainers.


e.

Align the 2 rear center ultrasonic sensor retainers with the mark on the rear bumper cover and install it as shown in the illustration.

E338238C02
2.885,2.802 3.115,2.615 false 4.125,2.594 4.479,2.75 false 3.167,2.5 3.479,2.698 0.313,0.198 10 true *a 3.906,2.5 4.219,2.698 0.313,0.198 10 true *a
*a Line - -
V100155

Press area - -


NOTICE:

The double-sided tape of a rear center ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new rear center ultrasonic sensor retainer when reattachment is necessary.


HINT:

Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the rear center ultrasonic sensor retainer to the rear bumper cover. Confirm there is no clearance between the rear center ultrasonic sensor retainer and rear bumper cover.



Hide 89348R 2.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

If a rear corner ultrasonic sensor retainer has been removed, replace it with a new one.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Clean the surface of the rear bumper cover.

i.

Remove any remaining double-sided tape from the rear bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 25 mm (0.984 in.)


Cover the sensor installation hole with a 25 mm (0.984 in.) circular piece of tape.


c.
E342077C01
1.406,0.542 1.802,0.729 false 1.198,0.448 1.417,0.635 0.219,0.188 10 true *a
*a Line
V100145

Primer


Using a brush or felt, apply primer or equivalent to the rear corner ultrasonic sensor retainer installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the rear bumper assembly until the primer has dried.




d.

Peel off the release paper from the rear corner ultrasonic sensor retainer.


e.
E342076C01
1.448,0.531 1.781,0.677 false 1.24,0.448 1.458,0.625 0.219,0.177 10 true *a
*a Line
V100155

Press area


Align the rear corner ultrasonic sensor retainer with the mark on the rear bumper cover and install it as shown in the illustration.

NOTICE:

The double-sided tape of a rear corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new rear corner ultrasonic sensor retainer when reattachment is necessary.


HINT:

Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the rear corner ultrasonic sensor retainer to the rear bumper cover. Confirm there is no clearance between the rear corner ultrasonic sensor retainer and rear bumper cover.



Hide 89348T 3.INSTALL REAR SIDE ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear side ultrasonic sensor retainer is necessary.

·

If a rear side ultrasonic sensor retainer has been removed, replace it with a new one.



a.

Clean the surface of the rear bumper cover.

i.

Remove any remaining double-sided tape from the rear bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 30 mm (1.18 in.)


Cover the 2 sensor installation holes with a 30 mm (1.18 in.) circular piece of tape.


c.

Using a brush or felt, apply primer or equivalent to the 2 rear side ultrasonic sensor retainers installation area.

E343308C02
2.26,0.76 2.677,0.458 false 5.427,0.406 5.854,0.708 false 3.938,0.073 4.313,0.313 0.375,0.24 12 false *B 0.833,0.083 1.208,0.323 0.375,0.24 12 false *A 2.729,0.354 3.042,0.552 0.313,0.198 10 false *a 5.24,0.313 5.552,0.51 0.313,0.198 10 false *a
*A for RH Side *B for LH Side
*a Line - -
V100145

Primer - -


NOTICE:
·

Use a clean brush or felt.

·

Do not touch the rear bumper assembly until the primer has dried.




d.

Peel off the release paper from the 2 rear side ultrasonic sensor retainers.


e.

Align the 2 rear side ultrasonic sensor retainers with the mark on the rear bumper cover and install it as shown in the illustration.

E343309C02
2.146,0.573 2.552,0.5 false 5.406,0.458 5.938,0.563 false 0.854,0.104 1.229,0.344 0.375,0.24 12 false *A 4,0.115 4.375,0.354 0.375,0.24 12 false *B 2.604,0.427 2.917,0.625 0.313,0.198 10 false *a 5.219,0.375 5.531,0.573 0.313,0.198 10 false *a
*A for RH Side *B for LH Side
*a Line - -
V100155

Press area - -


NOTICE:

The double-sided tape of a rear side ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new rear side ultrasonic sensor retainer when reattachment is necessary.


HINT:

Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the rear side ultrasonic sensor retainer to the rear bumper cover. Confirm there is no clearance between the rear side ultrasonic sensor retainer and rear bumper cover.



Hide 89342A 4.INSTALL REAR CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342056C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the rear center ultrasonic sensor as shown in the illustration.


b.

Connect the connector.


Hide 89342 5.INSTALL REAR CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342080C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the rear corner ultrasonic sensor as shown in the illustration.


b.

Connect the connector.


Hide 89342B 6.INSTALL REAR SIDE ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E342054C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the rear side ultrasonic sensor as shown in the illustration.


b.

Connect the connector.


Hide 7.INSTALL REAR BUMPER ASSEMBLY