Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS
RM3210E _59 Vehicle Exterior _047515 WINDOW / GLASS _0244714 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane departure alert system, pre-crash safety system, forward recognition camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 56115A 1.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B435092

Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.

HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56116C 2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

Using a brush or sponge, coat the installation area of 2 new No. 2 windshield glass stoppers with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B435093C01
0.917,0.5 1.229,0.865 false 1.615,1.042 1.417,1.5 false 1.906,0.99 1.417,1.5 1.417,1.5 1.333,1.094 false 0.125,0.063 0.427,0.396 0.302,0.333 12 false *A 1.354,1.51 1.667,1.667 0.313,0.156 10 false *a 0.74,0.406 1.052,0.563 0.313,0.156 10 false *b 2.708,0.74 2.865,0.938 0.156,0.198 10 false a
*A Back Side
*a Ceramic Notch
*b Windshield Glass Edge Side


Install the 2 new No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 13.7 to 14.7 mm (0.539 to 0.579 in.)


HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 75533G 3.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Using a brush or sponge, coat the installation area of a new windshield outside moulding with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B435094C01
0.854,2.188 1.104,2.552 false 2.604,2.198 2.365,2.563 false 0.115,0.104 0.427,0.438 0.313,0.333 12 false *A 1.031,2.583 1.344,2.74 0.313,0.156 10 false *a 2.26,2.583 2.573,2.74 0.313,0.156 10 false *a 1.292,1.24 1.448,1.438 0.156,0.198 10 false A 1.302,0.635 1.458,0.833 0.156,0.198 10 false A 0.979,3.281 1.49,3.563 0.51,0.281 10 false A-A 2.01,3.156 2.167,3.354 0.156,0.198 10 false a 0.771,1.656 1.031,1.854 0.26,0.198 10 false *b 2.552,1.656 2.813,1.875 0.26,0.219 10 false *b
*A Back Side
*a Edge Of Curved Surface
*b Same Length


Install the new windshield outside moulding to the windshield glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 6.9 mm (0.272 in.)



Hide 56117A 4.INSTALL WINDOW GLASS ADHESIVE DAM

a.
B274197C02
3.094,0.802 2.427,0.427 false 1.531,1.729 1.688,1.927 0.156,0.198 10 false a 2.26,0.344 2.573,0.542 0.313,0.198 10 false *a
*a Cut


Cut a new window glass adhesive dam so that it is the appropriate size as shown in the illustration.

Standard Dimension:
Area Dimension
a 294.2 to 295.2 cm (9.65 to 9.68 ft.)



b.

Using a brush or sponge, coat the installation area of the new window glass adhesive dam with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



c.

Install the window glass adhesive dam to the windshield glass as shown in the illustration.

B435095C01
4.865,1.958 5.281,1.542 false 3.25,4.333 3.01,4.125 false 2.156,1.208 2.573,1.042 false 3.042,4.094 3.25,4.333 3.25,4.333 2.99,4.146 false 4.875,3.635 5.292,3.219 false 2.573,4.271 2.833,4.5 2.833,4.5 2.448,4.333 false 0.146,0.125 0.438,0.438 0.292,0.313 12 false *A 2.667,0.969 2.979,1.125 0.313,0.156 10 false *a 4.771,2 5.083,2.156 0.313,0.156 10 false *b 4.833,3.688 5.146,3.844 0.313,0.156 10 false *b 3.344,4.281 3.656,4.438 0.313,0.156 10 false *a 2.875,4.438 3.188,4.594 0.313,0.156 10 false *a 2.677,2.979 2.833,3.177 0.156,0.198 10 false A 3.052,2.938 3.208,3.135 0.156,0.198 10 false A 2.031,4.042 2.188,4.24 0.156,0.198 10 false B 2.042,4.458 2.198,4.656 0.156,0.198 10 false B 4.667,0.813 5.156,1.052 0.49,0.24 10 false A-A 4.667,2.552 5.156,2.792 0.49,0.24 10 false B-B
*A Back Side - -
*a Ceramic Notch *b Window Glass Adhesive Dam Positioning Center
V100155

Primer G - -



Hide 56153C 5.INSTALL FRONT WINDOW INNER CENTER MOULDING

HINT:

Perform the following procedure only when replacement of a front window inner center moulding is necessary.


a.
B435173C01
0.135,0.083 0.448,0.365 0.313,0.281 12 false *A 0.75,1.729 0.969,1.948 0.219,0.219 10 false A 0.677,2.219 0.896,2.438 0.219,0.219 10 false A 0.896,2.896 1.417,3.156 0.521,0.26 10 false A-A 1.604,3.156 1.823,3.375 0.219,0.219 10 false a
*A Back Side
V100155

Primer G


Using a brush or sponge, coat the installation area of a new front window inner center moulding with primer G.

Standard Dimension:
Area Dimension
a 17.5 mm (0.689 in.) or more


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B435167C01
1.917,2.49 1.917,2.365 false 1.677,2.469 1.677,2.365 1.677,2.365 2.177,2.365 false 0.146,0.094 0.521,0.333 0.375,0.24 12 false *A 0.771,1.479 0.927,1.677 0.156,0.198 10 false A 0.677,1.927 0.833,2.125 0.156,0.198 10 false A 0.448,3.354 0.885,3.625 0.438,0.271 10 false A-A 1.01,4.198 1.167,4.396 0.156,0.198 10 false a 2.25,2.292 2.563,2.49 0.313,0.198 10 false *a
*A Back Side
*a Matchmark


Install the new front window inner center moulding to the windshield glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 0.6 mm (0.0236 in.) or less


NOTICE:

Do not damage the front window inner center moulding.



c.

Remove the matchmarks.


Hide 56111 6.INSTALL WINDSHIELD GLASS SUB-ASSEMBLY

a.
B435084C01
1.375,1.688 1.375,1.104 1.375,1.104 1.635,1.104 true 1.385,1.385 1.635,1.385 true 1.323,1.698 1.635,1.854 0.313,0.156 10 false *a
*a Matchmark


Position the windshield glass sub-assembly.

i.

Using suction cups, place the windshield glass sub-assembly in the correct position.


ii.

Check that the whole contact surface of the windshield glass sub-assembly rim is perfectly even.


iii.

Align the matchmarks on the windshield glass sub-assembly and vehicle body.

NOTICE:

Check that the windshield glass stoppers are engaged to the vehicle body correctly.



iv.

Remove the windshield glass sub-assembly.



b.

Using a brush, coat the installation surface on the vehicle body with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



c.

Using a brush or sponge, coat the adhesive application area with primer G.

B435096C01
3.208,2.333 3.583,2.5 3.583,2.5 3.281,2.323 false 3.229,1.677 3.667,1.844 false 3.292,2.281 3.583,2.5 3.583,2.5 3.292,2.031 false 0.146,0.115 0.438,0.427 0.292,0.313 12 false *A 3.75,1.781 4.063,1.938 0.313,0.156 10 false *a 3.656,2.448 3.969,2.604 0.313,0.156 10 false *b 1.031,0.667 1.188,0.865 0.156,0.198 10 false A 1.01,0.958 1.167,1.156 0.156,0.198 10 false A 1.667,0.688 1.823,0.885 0.156,0.198 10 false B 1.677,0.979 1.833,1.177 0.156,0.198 10 false B 2.958,1.125 3.115,1.323 0.156,0.198 10 false C 3.271,1.073 3.427,1.271 0.156,0.198 10 false C 2.302,2.146 2.458,2.344 0.156,0.198 10 false D 2.292,2.625 2.448,2.823 0.156,0.198 10 false D 3.094,2.531 3.25,2.729 0.156,0.198 10 false E 3,2.063 3.156,2.26 0.156,0.198 10 false E 0.563,3.281 1.031,3.5 0.469,0.219 10 false A-A 2.844,3.292 3.313,3.51 0.469,0.219 10 false B-B 5.094,0.51 5.563,0.729 0.469,0.219 10 false C-C 4.948,1.802 5.417,2.021 0.469,0.219 10 false D-D 4.833,3.188 5.302,3.406 0.469,0.219 10 false E-E 3.406,3.292 3.563,3.49 0.156,0.198 10 false a 5.792,1.854 5.948,2.052 0.156,0.198 10 false b 5.771,3.26 5.927,3.458 0.156,0.198 10 false c
*A Back Side - -
*a Adhesive Application Area *b Ceramic Notch
V100155

Primer G - -


Standard Dimension:
Area Dimension
a 8.0 mm (0.315 in.)
b 11.0 mm (0.433 in.) or more
c 19.0 mm (0.748 in.) or more


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:
·

Apply primer G to the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.




d.

Apply adhesive to the windshield glass sub-assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 to 15.0 mm (0.472 to 0.591 in.)
b 8.0 to 11.0 mm (0.315 to 0.433 in.)



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the windshield glass sub-assembly as shown in the illustration.

B435097C01
3.229,1.646 3.771,1.792 false 5.615,2.438 5.281,2.76 false 5.396,3.833 5.063,4.156 false 3.25,2.302 3.5,2.417 3.5,2.417 3.219,2.333 false 3.292,2.073 3.5,2.417 3.5,2.417 3.281,2.271 false 0.125,0.104 0.417,0.438 0.292,0.333 12 false *A 3.823,1.719 4.135,1.875 0.313,0.156 10 false *a 5.219,2.792 5.531,2.948 0.313,0.156 10 false *b 3.552,2.375 3.865,2.531 0.313,0.156 10 false *c 4.99,4.198 5.302,4.354 0.313,0.156 10 false *b 1.021,0.677 1.198,0.896 0.177,0.219 10 false A 1.01,0.969 1.188,1.188 0.177,0.219 10 false A 1.677,0.698 1.854,0.917 0.177,0.219 10 false B 1.677,0.979 1.854,1.198 0.177,0.219 10 false B 2.969,1.146 3.146,1.365 0.177,0.219 10 false C 3.26,1.094 3.438,1.313 0.177,0.219 10 false C 2.302,2.156 2.479,2.375 0.177,0.219 10 false D 2.302,2.635 2.479,2.854 0.177,0.219 10 false D 2.99,2.073 3.167,2.292 0.177,0.219 10 false E 3.104,2.542 3.281,2.76 0.177,0.219 10 false E 0.656,3.26 1.125,3.49 0.469,0.229 10 false A-A 2.885,3.313 3.354,3.542 0.469,0.229 10 false B-B 5.104,0.396 5.573,0.625 0.469,0.229 10 false C-C 4.958,1.729 5.427,1.958 0.469,0.229 10 false D-D 4.708,3.104 5.177,3.333 0.469,0.229 10 false E-E 1.656,4.208 1.969,4.406 0.313,0.198 10 false a 3.563,4.25 3.875,4.448 0.313,0.198 10 false b 6.25,0.385 6.563,0.583 0.313,0.198 10 false c 5.677,1.781 5.99,1.979 0.313,0.198 10 false d 5.479,3.031 5.792,3.229 0.313,0.198 10 false e 5.708,3.427 6.021,3.625 0.313,0.198 10 false f
*A Back Side - -
*a Adhesive Positioning Center *b Window Glass Adhesive Dam Positioning Center
*c Ceramic Notch - -
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 10.2 mm (0.402 in.)
b 10.2 mm (0.402 in.)
c 4.0 mm (0.157 in.)
d 6.5 mm (0.256 in.)
e 6.5 mm (0.256 in.)
f 8.0 mm (0.315 in.)


HINT:

Apply adhesive to the ceramic notches.




e.
B435084C01
1.375,1.688 1.375,1.104 1.375,1.104 1.635,1.104 true 1.385,1.385 1.635,1.385 true 1.323,1.698 1.635,1.854 0.313,0.156 10 false *a
*a Matchmark


Install the windshield glass sub-assembly.

i.

Using suction cups, position the windshield glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the windshield glass stoppers are engaged to the vehicle body correctly.

·

Check the clearance between the vehicle body and windshield glass sub-assembly.




ii.

Lightly press the outer surface of the windshield glass sub-assembly to ensure that the windshield glass sub-assembly is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the windshield glass sub-assembly using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




f.

When replacing the windshield glass sub-assembly or front window inner center moulding with a new one:

i.
B435165N01
2.156,1.792 2.313,1.99 0.156,0.198 10 false A 2.229,2.594 2.385,2.792 0.156,0.198 10 false A 0.792,3.031 1.219,3.292 0.427,0.26 10 false A-A

Remove the 2 protective retainers from the front window inner center moulding.

NOTICE:

Do not damage the front window inner center moulding.


HINT:

Make sure to remove the protective retainers.




Hide 7.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 86050 8.INSTALL TELEVISION ANTENNA ASSEMBLY (w/ Television Antenna)

Hide 863C0 9.INSTALL DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY (w/ Digital Audio Broadcasting Antenna)

Hide 10.INSTALL ROOF HEADLINING ASSEMBLY

a.

Return the front section of the roof headlining assembly to its original position.


Hide 74348C 11.INSTALL VISOR HOLDER LH

Hide 74320 12.INSTALL VISOR ASSEMBLY LH

Hide 74325 13.INSTALL VISOR BRACKET COVER (for LH Side)

Hide 74348B 14.INSTALL VISOR HOLDER RH

HINT:

Use the same procedure as for the LH side.


Hide 74310 15.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74325 16.INSTALL VISOR BRACKET COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 74610A 17.INSTALL ASSIST GRIP ASSEMBLY

Hide 62212 18.INSTALL FRONT PILLAR GARNISH LH

Hide 62312B 19.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62211 20.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 21.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 81260A 22.INSTALL MAP LIGHT ASSEMBLY

Hide 8646C 23.INSTALL FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)

Hide 89941 24.INSTALL RAIN SENSOR (w/ Rain Sensor)

Hide 88620E 25.INSTALL AIR CONDITIONING THERMISTOR ASSEMBLY (w/ Humidity Sensor)

Hide 55781E 27.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 55754F 28.INSTALL COWL WATER EXTRACT SHIELD LH

Hide 55753D 29.INSTALL COWL WATER EXTRACT SHIELD RH

HINT:

Use the same procedure as for the LH side.


Hide 30.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 31.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85292B 32.INSTALL FRONT WIPER ARM HEAD CAP

Hide 75534 33.INSTALL WINDSHIELD MOULDING OUTSIDE LH

Hide 75533 34.INSTALL WINDSHIELD MOULDING OUTSIDE RH

HINT:

Use the same procedure as for the LH side.