Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM3210E _52 Drivetrain _047521 DRIVE SHAFT / PROPELLER SHAFT _0243355 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 41336E 1.INSTALL FRONT DRIVE SHAFT DUST COVER (for LH Side)

a.
F041033C11
0.49,0.635 0.49,0.417 0.49,0.417 0.365,0.417 false 0.188,0.323 0.594,0.479 0.406,0.156 10 false *a
*a Steel Plate


Using a steel plate and a press, install a new front drive shaft dust cover.

NOTICE:
·

The dust cover should be completely installed.

·

Be careful not to damage the front drive shaft dust cover.

·

Install the front drive shaft dust cover in the correct orientation.




Hide 41336D 2.INSTALL FRONT DRIVE SHAFT DUST COVER (for RH Side)

a.
C157559C04
1.292,0.719 1.292,0.292 1.292,0.292 1.427,0.292 false 1.469,0.229 1.938,0.542 0.469,0.313 10 false *a
*a Steel Plate


Using a steel plate and a press, install a new front drive shaft dust cover.

NOTICE:
·

The dust cover should be completely installed.

·

Be careful not to damage the front drive shaft dust cover.

·

Install the front drive shaft dust cover in the correct orientation.




Hide 3.INSTALL FRONT AXLE OUTBOARD JOINT BOOT (for LH Side)

a.
C166359C04
1.917,0.885 2.427,0.375 2.427,0.375 2.792,0.375 false 2.823,0.281 3.177,0.49 0.354,0.208 10 *a
*a Protective Tape


Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274280C01
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard Grease Capacity:

135 to 145 g (4.77 to 5.11 oz)



d.

Install the front axle outboard joint boot to the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 43447F 4.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


a.
C107943

Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever to the guide groove correctly and install the clamp as far to the inside of the vehicle as possible.

·

Check the band and the lever for any deformation before folding back the lever.




b.
C158355C05
1.521,0.333 1.854,0.625 0.333,0.292 10 false *a 2.219,2.063 2.552,2.333 0.333,0.271 10 false *b
*a Weight
*b Contact


Lean your weight on your hand and roll the outboard joint forward while pressing the outboard joint against the work surface. Roll the outboard joint and fold the lever until a click sound can be heard.

NOTICE:
·

Do not damage the deflector.

·

Make sure that the outboard joint is in direct contact with the work surface.




c.
C265825C09
1.698,3.74 1.135,4.417 1.135,4.417 1.896,3.771 true 0.979,4.406 1.292,4.604 0.313,0.198 10 false *a
*a Buckle


Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle outboard joint boot.




Hide 43447E 5.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


a.
C107948

Install the front axle outboard joint boot clamp to the front axle outboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever to the guide groove correctly.

·

Check the band and the lever for any deformation before folding back the lever.




b.
C158356C01
2.469,0.938 2.771,1.219 0.302,0.281 10 false *a
*a Place the tip near the center of the lever


Using water pump pliers, pinch the front axle outboard joint boot clamp to temporarily secure it until a click sound can be heard.

NOTICE:

Do not damage the front axle outboard joint boot.



c.
C264475C07
1.615,3.552 1.125,4.333 1.125,4.333 1.365,3.542 true 0.99,4.333 1.302,4.531 0.313,0.198 10 false *a
*a Buckle


Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle outboard joint boot.




Hide 43474E 6.INSTALL FRONT DRIVE SHAFT DAMPER (for LH Side)

a.

w/ 1 Clamp:

i.
C351325C02
0.542,1.74 0.542,1.438 false 1.125,1.677 1.125,1.375 false 0.479,1.771 0.792,1.927 0.313,0.156 10 false *1 1.073,1.719 1.385,1.875 0.313,0.156 10 false *2 1.365,0.313 1.521,0.51 0.156,0.198 10 false A
*1 Front Drive Shaft Damper
*2 Front Drive Shaft Damper Clamp


Temporarily install the front drive shaft damper and a new front drive shaft damper clamp to the front drive outboard joint shaft assembly as shown in the illustration.

Dimension (A):

211.7 to 215.7 mm (8.34 to 8.49 in.)




b.

w/ 2 Clamps:

i.
C324681C04
0.646,1.667 0.646,1.354 false 1.229,1.573 1.229,1.26 false 0.188,1.573 0.188,1.26 false 1.479,0.208 1.635,0.406 0.156,0.198 10 false A 1.167,1.604 1.479,1.76 0.313,0.156 10 false *2 0.594,1.698 0.906,1.854 0.313,0.156 10 false *1 0.115,1.604 0.427,1.76 0.313,0.156 10 false *2
*1 Front Drive Shaft Damper
*2 Front Drive Shaft Damper Clamp


Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front drive outboard joint shaft assembly as shown in the illustration.

Dimension (A):

211.7 to 215.7 mm (8.34 to 8.49 in.)




c.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

w/ 1 Clamp:

i.

Install the front drive shaft damper clamp to the front drive shaft damper.

NOTICE:

Be sure to install the clamp in the correct position.



ii.
C351322C02
0.479,1.854 0.635,1.948 0.635,1.948 0.958,1.802 false 0.563,1.948 0.875,2.104 0.313,0.156 10 false *a
*a Claw


Using needle-nose pliers, engage each claw to install the front drive shaft damper clamp as shown in the illustration.

NOTICE:
·

Be sure to install the clamp in the correct position.

·

Do not damage the front drive shaft damper.

·

Do not damage the claws.





e.

w/ 2 Clamps:

i.

Install the 2 front drive shaft damper clamps to the front drive shaft damper.

NOTICE:

Be sure to install the clamp in the correct position.



ii.
C314741C03
0.51,1.844 0.698,1.938 0.698,1.938 1,1.76 false 0.635,1.938 0.948,2.094 0.313,0.156 10 false *a
*a Claw


Using needle-nose pliers, engage each claw to install the 2 front drive shaft damper clamps as shown in the illustration.

NOTICE:
·

Be sure to install the clamp in the correct position.

·

Do not damage the front drive shaft damper.

·

Do not damage the claws.





Hide 43474D 7.INSTALL FRONT DRIVE SHAFT DAMPER (for RH Side)

a.

w/ 1 Clamp:

i.
C351326C02
1.146,1.333 1.146,1.156 false 0.594,0.656 0.594,0.375 0.594,0.375 0.833,0.375 false 0.885,0.302 1.198,0.458 0.313,0.156 10 false *1 1.094,1.365 1.406,1.521 0.313,0.156 10 false *2 1.531,1.781 1.688,1.979 0.156,0.198 10 false A
*1 Front Drive Shaft Damper
*2 Front Drive Shaft Damper Clamp


Temporarily install the front drive shaft damper and a new front drive shaft damper clamp to the front drive outboard joint shaft assembly as shown in the illustration.

Dimension (A):

488.0 to 492.0 mm (1.602 to 1.614 ft.)




b.

w/ 2 Clamps:

i.
C314748C03
1.146,1.354 1.146,1.156 false 0.115,1.365 0.115,1.167 false 0.583,0.667 0.583,0.406 0.583,0.406 0.781,0.406 false 0.823,0.333 1.135,0.49 0.313,0.156 10 false *1 1.083,1.385 1.396,1.542 0.313,0.156 10 false *2 1.542,1.76 1.698,1.958 0.156,0.198 10 false A 0.063,1.385 0.375,1.542 0.313,0.156 10 false *2
*1 Front Drive Shaft Damper
*2 Front Drive Shaft Damper Clamp


Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front drive outboard joint shaft assembly as shown in the illustration.

Dimension (A):

488.0 to 492.0 mm (1.602 to 1.614 ft.)




c.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

w/ 1 Clamp:

i.

Install the front drive shaft damper clamp to the front drive shaft damper.

NOTICE:

Be sure to install the clamp in the correct position.



ii.
C351322C02
0.479,1.854 0.635,1.948 0.635,1.948 0.958,1.802 false 0.563,1.948 0.875,2.104 0.313,0.156 10 false *a
*a Claw


Using needle-nose pliers, engage each claw to install the front drive shaft damper clamp as shown in the illustration.

NOTICE:
·

Be sure to install the clamp in the correct position.

·

Do not damage the front drive shaft damper.

·

Do not damage the claws.





e.

w/ 2 Clamps:

i.

Install the 2 front drive shaft damper clamps to the front drive shaft damper.

NOTICE:

Be sure to install the clamp in the correct position.



ii.
C314741C03
0.51,1.844 0.698,1.938 0.698,1.938 1,1.76 false 0.635,1.938 0.948,2.094 0.313,0.156 10 false *a
*a Claw


Using needle-nose pliers, engage each claw to install the 2 front drive shaft damper clamps as shown in the illustration.

NOTICE:
·

Be sure to install the clamp in the correct position.

·

Do not damage the front drive shaft damper.

·

Do not damage the claws.





Hide 8.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C274277C02
0.688,1.875 0.688,1.333 false 1.698,1.854 1.698,1.615 false 2.49,1.875 2.49,1.667 false 2.927,1.885 2.927,1.25 false 0.625,1.896 0.938,2.052 0.313,0.156 10 *1 1.635,1.896 1.948,2.052 0.313,0.156 10 *2 2.417,1.906 2.729,2.063 0.313,0.156 10 *3 2.875,1.896 3.188,2.052 0.313,0.156 10 *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C067417C01
1.281,1.719 2.01,1.677 2.01,1.677 1.771,1.438 false 2.063,1.625 2.229,1.771 0.167,0.146 10 *a
*a Matchmark


Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



e.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.

·

Be sure to install the tripod joint in the correct direction.




f.
F045046

Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.


g.

Pack the front drive inboard joint assembly and front axle inboard boot with grease.

Standard Grease Capacity:

168 to 178 g (5.93 to 6.27 oz)



h.
C164752C06
2.177,1.667 2.531,1.667 2.531,1.667 2.531,1.365 false 2.021,1.573 2.333,1.771 0.313,0.198 10 false *a
*a Groove


Install a new front axle inboard joint grommet to the inboard joint groove.

NOTICE:

Securely fit the protrusion on the front axle inboard joint grommet into the inboard joint groove.



i.
C158439C13
1.948,0.667 0.938,0.25 0.938,0.25 1.396,1.281 false 0.74,0.167 0.927,0.344 0.188,0.177 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 9.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.

NOTICE:
·

Keep the grooves free of grease.

·

Keep the inside of the front axle inboard joint boot free of foreign matter.




Hide 43448F 10.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


a.
C107948

Install the front axle inboard joint boot clamp to the front axle inboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and the lever for any deformation before folding back the lever.




b.
C158356C01
2.469,0.938 2.771,1.219 0.302,0.281 10 false *a
*a Place the tip near the center of the lever


Using water pump pliers, pinch the front axle inboard joint boot clamp to temporarily secure it until a click sound can be heard.

NOTICE:

Do not damage the front axle inboard joint boot.



c.
C264475C08
1.344,3.594 0.948,4.302 0.948,4.302 1.635,3.594 true 0.781,4.292 1.094,4.49 0.313,0.198 10 false *a
*a Buckle


Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle inboard joint boot.




Hide 43448G 11.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


a.
C296188N01
1.438,1.656 1.594,1.854 0.156,0.198 10 false A

C296186C01
0.74,0.948 1.073,0.948 true 2.302,0.958 2.635,0.958 true 1.76,1.885 1.76,2.042 1.76,2.042 2.115,2.042 true 1.094,2.49 1.573,2.792 true 0.677,0.313 0.99,0.469 0.313,0.156 10 false *1 0.573,0.854 0.885,1.01 0.313,0.156 10 false *a 2.667,0.865 2.979,1.021 0.313,0.156 10 false *a 2.135,1.948 2.448,2.104 0.313,0.156 10 false *a 0.927,2.385 1.24,2.542 0.313,0.156 10 false *a
*1 Front Axle Inboard Joint Grommet
*a Recessed Parts


While keeping dimension (A) within the specified length, equalize the pressure within the inboard joint with atmospheric pressure by slightly lifting one of the recessed areas of the front axle inboard joint grommet from the front drive inboard joint assembly.

Dimension (A):
LH Side RH Side
581.2 mm (1.91 ft.) 880.2 mm (2.89 ft.)



b.
C296187C01
1.865,0.667 2.302,0.427 false 0.719,0.333 1.031,0.49 0.313,0.156 10 false *1 0.719,1.604 1.031,1.76 0.313,0.156 10 false *2 2.354,0.313 2.667,0.469 0.313,0.156 10 false *a 1.688,1.24 1.844,1.438 0.156,0.198 10 false B 2.438,2.479 2.594,2.677 0.156,0.198 10 false B 0.958,2.469 1.115,2.667 0.156,0.198 10 false B
*1 Front No. 2 Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Grommet
*a Fulcrum Point


Set the lever fulcrum point at any point (B) indicated in the illustration and temporarily bend the lever.

NOTICE:
·

Perform this work with the inside of the inboard joint kept at atmospheric pressure.

·

Set the lever into the guide groove correctly and install the clamp as far into the inside of the vehicle as possible.

·

Check the band and the lever for any deformation before folding back the lever.




c.
C158448C04
1.375,0.281 1.615,0.51 0.24,0.229 10 *a 2.208,2.021 2.417,2.229 0.208,0.208 10 *b
*a Weight
*b Contact


Lean your weight on your hand and roll the inboard joint forward while pressing the inboard joint against the work surface. Roll the inboard joint and fold the lever until a click sound can be heard.

NOTICE:
·

Make sure that the inboard joint is in direct contact with the work surface.

·

Do not damage the front drive shaft dust cover.




d.
C158764C05
1.802,3.719 1.115,4.375 1.115,4.375 1.615,3.698 true 0.979,4.365 1.292,4.563 0.313,0.198 10 false *a
*a Buckle


Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle inboard joint boot.