Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2015.11–2016.08
RM3210E _56 Audio / Visual / Telematics _047510 AUDIO / VIDEO _0243397 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Speaker Circuit  


DESCRIPTION

for 6 Speakers

If there is a short in a speaker circuit, the navigation receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.


for 10 Speakers

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.


WIRING DIAGRAM

for 6 Speakers
E226481E81
5.354,7.469 7.073,8.073 1.719,0.604 10 false Radio and Display Receiver Assembly 3.021,1.26 4.281,2.031 1.26,0.771 10 false Front No. 2 Speaker Assembly RH 5.552,0.771 5.833,1.042 0.281,0.271 10 false 1 4.542,0.844 4.792,1.063 0.25,0.219 10 false 4 4.542,1.719 5.042,2 0.5,0.281 10 false 2 2.313,0.844 2.604,1.125 0.292,0.281 10 false 3 2.313,1.708 2.594,2.156 0.281,0.448 10 false 1 2.49,0.844 2.813,1.073 0.323,0.229 10 false + 2.5,1.688 2.708,1.927 0.208,0.24 10 false - 4.073,0.854 4.667,1.083 0.594,0.229 10 false TWR+ 4.083,1.708 4.635,1.969 0.552,0.26 10 false TWR- 5.469,0.938 5.833,1.25 0.365,0.313 10 false F32 3.01,1.094 3.271,1.25 0.26,0.156 10 false G3 0.344,1.406 1.625,2.063 1.281,0.656 10 false Front No. 1 Speaker Assembly RH 0.354,1.26 0.615,1.417 0.26,0.156 10 false I1 3.021,3.24 4.313,3.948 1.292,0.708 10 false Front No. 2 Speaker Assembly LH 4.542,2.813 5,3 0.458,0.188 10 false 4 4.531,3.688 5.073,4.042 0.542,0.354 10 false 2 2.323,2.813 2.615,3.094 0.292,0.281 10 false 3 2.313,3.688 2.677,3.958 0.365,0.271 10 false 1 2.469,2.802 2.896,3.073 0.427,0.271 10 false + 2.479,3.667 2.833,3.854 0.354,0.188 10 false - 4.083,2.813 4.792,3.26 0.708,0.448 10 false TWL+ 4.115,3.677 4.719,3.938 0.604,0.26 10 false TWL- 3.01,3.073 3.271,3.229 0.26,0.156 10 false G6 0.344,3.365 1.615,4.052 1.271,0.688 10 false Front No. 1 Speaker Assembly LH 0.354,3.219 0.615,3.375 0.26,0.156 10 false J1 0.74,5.125 1.625,5.813 0.885,0.688 10 false Rear Speaker Assembly RH 0.74,4.979 1.052,5.177 0.313,0.198 10 false K4 0.74,6.677 1.604,7.344 0.865,0.667 10 false Rear Speaker Assembly LH 0.74,6.521 1.156,6.802 0.417,0.281 10 false L5 5.469,1.813 6.063,2.208 0.594,0.396 10 false F32 5.458,2.917 6.094,3.146 0.635,0.229 10 false F32 5.458,3.781 5.99,4.063 0.531,0.281 10 false F32 5.469,4.833 5.906,5.177 0.438,0.344 10 false F33 5.458,5.469 5.969,5.76 0.51,0.292 10 false F33 5.469,6.344 5.948,6.604 0.479,0.26 10 false F33 5.469,6.979 5.938,7.271 0.469,0.292 10 false F33 5.823,0.938 6.302,1.229 0.479,0.292 10 false FR+ 5.833,1.813 6.427,2.083 0.594,0.271 10 false FR- 5.823,2.896 6.271,3.25 0.448,0.354 10 false FL+ 5.833,3.781 6.417,4.115 0.583,0.333 10 false FL- 5.833,4.844 6.344,5.115 0.51,0.271 10 false RR+ 5.833,5.448 6.219,5.74 0.385,0.292 10 false RR- 5.833,6.344 6.208,6.656 0.375,0.313 10 false RL+ 5.833,6.958 6.094,7.115 0.26,0.156 10 false RL- 5.542,6.802 5.938,6.99 0.396,0.188 10 false 6 5.552,6.177 5.854,6.438 0.302,0.26 10 false 2 5.552,5.292 5.958,5.594 0.406,0.302 10 false 3 5.552,4.667 5.917,4.958 0.365,0.292 10 false 1 5.552,3.604 5.823,3.813 0.271,0.208 10 false 6 5.552,2.74 5.927,3.073 0.375,0.333 10 false 2 5.552,1.635 5.875,1.885 0.323,0.25 10 false 5 1.792,1.073 2.448,1.323 0.656,0.25 10 false 1 1.792,1.708 2.177,1.865 0.385,0.156 10 false 2 1.792,3.042 2.208,3.323 0.417,0.281 10 false 1 1.792,3.677 2.156,3.948 0.365,0.271 10 false 2 1.792,4.854 2.094,5.188 0.302,0.333 10 false 1 1.792,5.5 2.115,5.729 0.323,0.229 10 false 2 1.792,6.365 2.073,6.594 0.281,0.229 10 false 1 1.792,7.01 2.188,7.26 0.396,0.25 10 false 2

for 10 Speakers
E338642E01
5.781,9.021 6.979,9.583 1.198,0.563 10 false Stereo Component Amplifier Assembly 5.802,8.865 6.854,9.115 1.052,0.25 10 false F60 1.125,6.406 2,6.99 0.875,0.583 10 false Rear Speaker Assembly RH 1.188,7.844 2.063,8.427 0.875,0.583 10 false Rear Speaker Assembly LH 0.76,3.635 2.063,4.208 1.302,0.573 10 false Front No. 1 Speaker Assembly RH 0.854,4.99 2.146,5.615 1.292,0.625 10 false Front No. 1 Speaker Assembly LH 0.677,0.708 1.979,1.281 1.302,0.573 10 false Front No. 2 Speaker Assembly RH 0.708,1.99 2.01,2.563 1.302,0.573 10 false Front No. 2 Speaker Assembly LH 5.948,1.094 6.417,1.375 0.469,0.281 10 false TWR- 5.948,0.49 6.406,0.76 0.458,0.271 10 false TWR+ 5.948,4.75 6.281,5.031 0.333,0.281 10 false FL+ 5.948,5.542 6.281,5.823 0.333,0.281 10 false FL- 5.927,3.396 6.26,3.677 0.333,0.281 10 false FR+ 5.938,4.188 6.271,4.469 0.333,0.281 10 false FR- 5.948,1.896 6.406,2.167 0.458,0.271 10 false TWL+ 5.958,2.531 6.417,2.802 0.458,0.271 10 false TWL- 5.958,6.323 6.292,6.604 0.333,0.281 10 false RR+ 5.948,6.979 6.281,7.26 0.333,0.281 10 false RR- 5.948,7.708 6.281,7.99 0.333,0.281 10 false RL+ 5.948,8.375 6.281,8.656 0.333,0.281 10 false RL- 5.677,4.625 6.01,4.906 0.333,0.281 10 false 8 5.656,1.76 5.99,2.042 0.333,0.281 10 false 10 5.667,6.219 6,6.5 0.333,0.281 10 false 11 5.667,7.583 6,7.865 0.333,0.281 10 false 12 5.646,0.344 5.979,0.625 0.333,0.281 10 false 13 5.646,3.229 5.979,3.51 0.333,0.281 10 false 15 5.656,5.427 5.99,5.708 0.333,0.281 10 false 23 5.688,2.417 6.021,2.698 0.333,0.281 10 false 25 5.656,6.844 5.99,7.125 0.333,0.281 10 false 26 5.677,8.229 6.01,8.51 0.333,0.281 10 false 27 5.688,0.969 6.021,1.25 0.333,0.281 10 false 28 5.667,4.042 6,4.323 0.333,0.281 10 false 30 0.74,3.417 1.469,3.688 0.729,0.271 10 false I1 0.802,4.792 1.531,5.063 0.729,0.271 10 false J1 0.677,1.76 1.406,2.031 0.729,0.271 10 false G5 0.667,0.438 1.396,0.708 0.729,0.271 10 false G4 1.135,7.625 1.865,7.896 0.729,0.271 10 false L5 1.115,6.156 1.844,6.427 0.729,0.271 10 false K4 3.51,0.333 4.24,0.604 0.729,0.271 10 false 4 3.5,0.969 4.229,1.24 0.729,0.271 10 false 3 3.531,1.781 4.26,2.052 0.729,0.271 10 false 4 2.385,4.083 3.115,4.354 0.729,0.271 10 false 2 2.396,3.427 3.125,3.698 0.729,0.271 10 false 1 2.406,4.792 3.135,5.063 0.729,0.271 10 false 1 2.385,5.448 3.115,5.719 0.729,0.271 10 false 2 3.531,6.177 4.26,6.448 0.729,0.271 10 false 1 3.531,7.604 4.26,7.875 0.729,0.271 10 false 1 3.531,6.823 4.26,7.094 0.729,0.271 10 false 2 3.552,8.229 4.281,8.5 0.729,0.271 10 false 2 3.542,2.396 4.271,2.667 0.729,0.271 10 false 3

PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for 6 Speakers A
for 10 Speakers B




A

2.CHECK SPEAKER (OPERATION CHECK)

B

8.CHECK SPEAKER (OPERATION CHECK)
2.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly or front No. 2 speaker assembly A
Rear speaker assembly B


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the F32 radio and display receiver assembly connector.


b.

Disconnect the I1 and J1 front No. 1 speaker assembly connectors.


c.

Disconnect the G3 and G6 front No. 2 speaker assembly connectors.


d.

Measure the resistance between each of the front No. 2 speaker assemblies and the radio and display receiver assembly to check for an open in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
F32-1 (FR+) - G3-4 (TWR+) Always Below 1 Ω
F32-5 (FR-) - G3-2 (TWR-) Always Below 1 Ω
F32-2 (FL+) - G6-4 (TWL+) Always Below 1 Ω
F32-6 (FL-) - G6-2 (TWL-) Always Below 1 Ω



e.

Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-1 - G3-3 (+) Always Below 1 Ω
I1-2 - G3-1 (-) Always Below 1 Ω
J1-1 - G6-3 (+) Always Below 1 Ω
J1-2 - G6-1 (-) Always Below 1 Ω



f.

Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
F32-1 (FR+) or G3-4 (TWR+) - Body ground Always 10 kΩ or higher
F32-5 (FR-) or G3-2 (TWR-) - Body ground Always 10 kΩ or higher
F32-2 (FL+) or G6-4 (TWL+) - Body ground Always 10 kΩ or higher
F32-6 (FL-) or G6-2 (TWL-) - Body ground Always 10 kΩ or higher



g.

Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-1 or G3-3 (+) - Body ground Always 10 kΩ or higher
I1-2 or G3-1 (-) - Body ground Always 10 kΩ or higher
J1-1 or G6-3 (+) - Body ground Always 10 kΩ or higher
J1-2 or G6-1 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


c.

Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
a.

Disconnect the F33 radio and display receiver assembly connector.


b.

Disconnect the L5 and K4 rear speaker assembly connectors.


c.

Measure the resistance between each of the rear speaker assemblies and the radio and display receiver assembly to check for an open in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
F33-1 (RR+) - K4-1 Always Below 1 Ω
F33-3 (RR-) - K4-2 Always Below 1 Ω
F33-2 (RL+) - L5-1 Always Below 1 Ω
F33-6 (RL-) - L5-2 Always Below 1 Ω



d.

Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
F33-1 (RR+) or K4-1 - Body ground Always 10 kΩ or higher
F33-3 (RR-) or K4-2 - Body ground Always 10 kΩ or higher
F33-2 (RL+) or L5-1 - Body ground Always 10 kΩ or higher
F33-6 (RL-) or L5-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT REAR SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT REAR SPEAKER ASSEMBLY
a.

Remove the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL


b.

Inspect the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

8.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly A
Front No. 2 speaker assembly B
Rear speaker assembly C


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

9.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)

B

11.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

C

13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)
a.

Disconnect the F60 stereo component amplifier assembly connector.


b.

Disconnect the I1 and J1 front No. 1 speaker assembly connectors.


c.

Measure the resistance between each of the front No. 1 speaker assemblies and the stereo component amplifier assembly to check for an open in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
F60-15 (FR+) - I1-1 Always Below 1 Ω
F60-30 (FR-) - I1-2 Always Below 1 Ω
F60-8 (FL+) - J1-1 Always Below 1 Ω
F60-23 (FL-) - J1-2 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
F60-15 (FR+) or I1-1 - Body ground Always 10 kΩ or higher
F60-30 (FR-) or I1-2 - Body ground Always 10 kΩ or higher
F60-8 (FL+) or J1-1 - Body ground Always 10 kΩ or higher
F60-23 (FL-) or J1-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the F60 stereo component amplifier assembly connector.


b.

Disconnect the G4 and G5 front No. 2 speaker assembly connectors.


c.

Measure the resistance between each of the front No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
F60-13 (TWR+) - G4-4 Always Below 1 Ω
F60-28 (TWR-) - G4-3 Always Below 1 Ω
F60-10 (TWL+) - G5-4 Always Below 1 Ω
F60-25 (TWL-) - G5-3 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
F60-13 (TWR+) or G4-4 - Body ground Always 10 kΩ or higher
F60-28 (TWR-) or G4-3 - Body ground Always 10 kΩ or higher
F60-10 (TWL+) or G5-4 - Body ground Always 10 kΩ or higher
F60-25 (TWL-) or G5-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


c.

Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)
a.

Disconnect the F60 stereo component amplifier assembly connector.


b.

Disconnect the K4 and L5 rear speaker assembly connectors.


c.

Measure the resistance between each of the rear speaker assemblies and the stereo component amplifier assembly to check for an open in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
F60-11 (RR+) - K4-1 Always Below 1 Ω
F60-26 (RR-) - K4-2 Always Below 1 Ω
F60-12 (RL+) - L5-1 Always Below 1 Ω
F60-27 (RL-) - L5-2 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
F60-11 (RR+) or K4-1 - Body ground Always 10 kΩ or higher
F60-26 (RR-) or K4-2 - Body ground Always 10 kΩ or higher
F60-12 (RL+) or L5-1 - Body ground Always 10 kΩ or higher
F60-27 (RL-) or L5-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.INSPECT REAR SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT REAR SPEAKER ASSEMBLY
a.

Remove the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL


b.

Inspect the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION


c.

Check that the malfunction disappears when a new or known good rear speaker assembly is installed.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE