Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM3210E _56 Audio / Visual / Telematics _047510 AUDIO / VIDEO _0243397 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the meter circuit plate to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the meter circuit plate. The signal is changed to a pulse signal at the transistor in the meter circuit plate. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E342182E01
1.531,2.115 1.99,2.313 0.458,0.198 10 false SPD 1.531,0.229 1.99,0.427 0.458,0.198 10 false SP1 1.927,0.208 2.385,0.406 0.458,0.198 10 false 11 1.917,2.104 2.375,2.302 0.458,0.198 10 false 19 1.542,4.958 2,5.156 0.458,0.198 10 false SPD 1.906,4.958 2.365,5.156 0.458,0.198 10 false 11 2.802,2.021 3.26,2.219 0.458,0.198 10 false 19 4.302,2.01 4.76,2.208 0.458,0.198 10 false 16 4.302,3.479 4.76,3.677 0.458,0.198 10 false 18 5.313,0.208 5.771,0.406 0.458,0.198 10 false 20 5.594,0.323 6.052,0.521 0.458,0.198 10 false SI 5.594,2.219 6.052,2.417 0.458,0.198 10 false +S 5.313,2.104 5.771,2.302 0.458,0.198 10 false 19 5.313,3.563 5.771,3.76 0.458,0.198 10 false 17 5.594,3.583 6.052,3.781 0.458,0.198 10 false SPD 5.615,4.938 6.073,5.135 0.458,0.198 10 false SPD 5.313,4.927 5.771,5.125 0.458,0.198 10 false 17 0.323,0.844 0.781,1.042 0.458,0.198 10 false A41 0.302,1.01 2.375,1.427 2.073,0.417 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.417,2.521 2.208,2.948 1.792,0.427 10 false Certification ECU (Smart Key ECU Assembly) 0.438,2.365 0.896,2.563 0.458,0.198 10 false F1 0.417,5.208 0.875,5.406 0.458,0.198 10 false F61 0.406,5.375 2.208,5.729 1.802,0.354 10 false Stereo Component Amplifier Assembly*3 5.135,2.375 5.594,2.573 0.458,0.198 10 false F6 5.135,2.531 6.969,2.958 1.833,0.427 10 false Combination Meter Assembly (Meter Circuit Plate) 2.792,4.854 3.25,5.052 0.458,0.198 10 false 17 2.635,5.719 4.49,5.948 1.854,0.229 10 false No. 17 Junction Connector*5 5.073,3.844 5.531,4.042 0.458,0.198 10 false F92 5.323,5.396 7.042,5.865 1.719,0.469 10 false Radio and Display Receiver Assembly*2 5.073,4 7.156,4.208 2.083,0.208 10 false Navigation Receiver Assembly*1 5.031,5.396 5.49,5.594 0.458,0.198 10 false F31 2.667,6.125 4.75,6.333 2.083,0.208 10 false *2: for Radio and Display Type 0.344,6.115 2.427,6.323 2.083,0.208 10 false *1: for Navigation Receiver Type 3.99,2.01 4.448,2.208 0.458,0.198 10 false 7 3.958,3.479 4.417,3.677 0.458,0.198 10 false 10 2.427,2.021 2.885,2.219 0.458,0.198 10 false 11 2.469,4.854 2.656,5.094 0.188,0.24 10 false 9 4.271,2.208 4.729,2.406 0.458,0.198 10 false F85 4.271,3.677 4.729,3.875 0.458,0.198 10 false F85 2.76,2.219 3.219,2.417 0.458,0.198 10 false F85 2.75,5.063 3.208,5.26 0.458,0.198 10 false F85 3.906,2.208 4.177,2.417 0.271,0.208 10 false F79 3.917,3.677 4.188,3.885 0.271,0.208 10 false F79 2.385,2.219 2.656,2.427 0.271,0.208 10 false F79 2.396,5.063 2.667,5.271 0.271,0.208 10 false F79 2.646,5.438 4.5,5.667 1.854,0.229 10 false No. 8 Junction Connector*4 4.854,6.146 6.104,6.333 1.25,0.188 10 false *3: for 10 Speakers 1.677,6.469 2.542,6.677 0.865,0.208 10 false *5: for RHD 0.354,6.458 1.219,6.667 0.865,0.208 10 false *4: for LHD 2.438,2.417 2.615,2.625 0.177,0.208 10 false *4 2.438,5.271 2.615,5.479 0.177,0.208 10 false *4 3.948,2.406 4.125,2.615 0.177,0.208 10 false *4 3.958,3.885 4.135,4.094 0.177,0.208 10 false *4 2.792,2.427 2.969,2.635 0.177,0.208 10 false *5 4.313,2.417 4.49,2.625 0.177,0.208 10 false *5 4.313,3.885 4.49,4.094 0.177,0.208 10 false *5 2.802,5.271 2.979,5.479 0.177,0.208 10 false *5

PROCEDURE

1.INSPECT METER CIRCUIT PLATE (OUTPUT WAVEFORM)
a.

Check the output waveform.

E265790C24
1.771,0.333 2.156,0.563 0.385,0.229 1.031,1.885 1.271,1.208 false 0.208,0.156 0.521,0.354 0.313,0.198 10 false *a 0.917,1.906 1.229,2.104 0.313,0.198 10 false +S 4.625,1.635 4.938,1.833 0.313,0.198 10 false A 6.01,1.438 6.406,1.667 0.396,0.229 10 false GND 1.875,0.354 2.188,0.552 0.313,0.198 10 false F6
*a Component with harness connected
(Meter Circuit Plate)
- -


i.

Remove the meter circuit plate with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F6-19 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F6-19 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)

NG

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

E265796C12
1.604,0.385 2.01,0.667 0.406,0.281 1.146,1.958 1.344,1.313 false 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 1.688,0.427 2,0.625 0.313,0.198 10 false F61 1,1.99 1.469,2.229 0.469,0.24 10 false SPD 4.573,1.813 4.885,2.01 0.313,0.198 10 false A 5.969,1.563 6.469,1.854 0.5,0.292 10 false GND
*a Component with harness connected
(Stereo Component Amplifier Assembly)
- -


i.

Remove the stereo component amplifier assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F61-11 (SPD) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F61-11 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)

C

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - NO. 17 JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the F61 stereo component amplifier assembly connector.


b.

Disconnect the F79 No. 11 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F61-11 (SPD) - F79-9 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the F6 meter circuit plate connector.


b.

Disconnect the F79 No. 11 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-19 (+S) - F79-7 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - NO. 17 JUNCTION CONNECTOR)
a.

Disconnect the F61 stereo component amplifier assembly connector.


b.

Disconnect the F85 No. 17 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F61-11 (SPD) - F85-17 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 17 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 17 JUNCTION CONNECTOR)
a.

Disconnect the F6 meter circuit plate connector.


b.

Disconnect the F85 No. 17 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-19 (+S) - F85-16 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 17 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR