Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3210E _58 Vehicle Interior _047509 METER / GAUGE / DISPLAY _0236932 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly (meter circuit plate) receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU (brake booster with master cylinder assembly) which uses this information to create the vehicle speed signal*a. The vehicle speed signal consists of pulses sent to the combination meter assembly (meter circuit plate) from the skid control ECU (brake booster with master cylinder assembly). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly (meter circuit plate). This voltage is sent to the skid control ECU (brake booster with master cylinder assembly). The pulse signal is created by switching the transistor in the skid control ECU (brake booster with master cylinder assembly) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly (meter circuit plate) via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly (meter circuit plate) is controlled by the signal from the skid control ECU (brake booster with master cylinder assembly). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly (meter circuit plate) controls its respective system based on this pulse signal.

*a: This vehicle speed signal is created by the skid control ECU (brake booster with master cylinder assembly). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly (meter circuit plate) operation. Combination meter assembly (meter circuit plate) components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

E342182E01
1.531,2.115 1.99,2.313 0.458,0.198 10 false SPD 1.531,0.229 1.99,0.427 0.458,0.198 10 false SP1 1.927,0.208 2.385,0.406 0.458,0.198 10 false 11 1.917,2.104 2.375,2.302 0.458,0.198 10 false 19 1.542,4.958 2,5.156 0.458,0.198 10 false SPD 1.906,4.958 2.365,5.156 0.458,0.198 10 false 11 2.802,2.021 3.26,2.219 0.458,0.198 10 false 19 4.302,2.01 4.76,2.208 0.458,0.198 10 false 16 4.302,3.479 4.76,3.677 0.458,0.198 10 false 18 5.313,0.208 5.771,0.406 0.458,0.198 10 false 20 5.594,0.323 6.052,0.521 0.458,0.198 10 false SI 5.594,2.219 6.052,2.417 0.458,0.198 10 false +S 5.313,2.104 5.771,2.302 0.458,0.198 10 false 19 5.313,3.563 5.771,3.76 0.458,0.198 10 false 17 5.594,3.583 6.052,3.781 0.458,0.198 10 false SPD 5.615,4.938 6.073,5.135 0.458,0.198 10 false SPD 5.313,4.927 5.771,5.125 0.458,0.198 10 false 17 0.323,0.844 0.781,1.042 0.458,0.198 10 false A41 0.302,1.01 2.375,1.427 2.073,0.417 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.417,2.521 2.208,2.948 1.792,0.427 10 false Certification ECU (Smart Key ECU Assembly) 0.438,2.365 0.896,2.563 0.458,0.198 10 false F1 0.417,5.208 0.875,5.406 0.458,0.198 10 false F61 0.406,5.375 2.208,5.729 1.802,0.354 10 false Stereo Component Amplifier Assembly*3 5.135,2.375 5.594,2.573 0.458,0.198 10 false F6 5.135,2.531 6.969,2.958 1.833,0.427 10 false Combination Meter Assembly (Meter Circuit Plate) 2.792,4.854 3.25,5.052 0.458,0.198 10 false 17 2.635,5.719 4.49,5.948 1.854,0.229 10 false No. 17 Junction Connector*5 5.073,3.844 5.531,4.042 0.458,0.198 10 false F92 5.323,5.396 7.042,5.865 1.719,0.469 10 false Radio and Display Receiver Assembly*2 5.073,4 7.156,4.208 2.083,0.208 10 false Navigation Receiver Assembly*1 5.031,5.396 5.49,5.594 0.458,0.198 10 false F31 2.667,6.125 4.75,6.333 2.083,0.208 10 false *2: for Radio and Display Type 0.344,6.115 2.427,6.323 2.083,0.208 10 false *1: for Navigation Receiver Type 3.99,2.01 4.448,2.208 0.458,0.198 10 false 7 3.958,3.479 4.417,3.677 0.458,0.198 10 false 10 2.427,2.021 2.885,2.219 0.458,0.198 10 false 11 2.469,4.854 2.656,5.094 0.188,0.24 10 false 9 4.271,2.208 4.729,2.406 0.458,0.198 10 false F85 4.271,3.677 4.729,3.875 0.458,0.198 10 false F85 2.76,2.219 3.219,2.417 0.458,0.198 10 false F85 2.75,5.063 3.208,5.26 0.458,0.198 10 false F85 3.906,2.208 4.177,2.417 0.271,0.208 10 false F79 3.917,3.677 4.188,3.885 0.271,0.208 10 false F79 2.385,2.219 2.656,2.427 0.271,0.208 10 false F79 2.396,5.063 2.667,5.271 0.271,0.208 10 false F79 2.646,5.438 4.5,5.667 1.854,0.229 10 false No. 8 Junction Connector*4 4.854,6.146 6.104,6.333 1.25,0.188 10 false *3: for 10 Speakers 1.677,6.469 2.542,6.677 0.865,0.208 10 false *5: for RHD 0.354,6.458 1.219,6.667 0.865,0.208 10 false *4: for LHD 2.438,2.417 2.615,2.625 0.177,0.208 10 false *4 2.438,5.271 2.615,5.479 0.177,0.208 10 false *4 3.948,2.406 4.125,2.615 0.177,0.208 10 false *4 3.958,3.885 4.135,4.094 0.177,0.208 10 false *4 2.792,2.427 2.969,2.635 0.177,0.208 10 false *5 4.313,2.417 4.49,2.625 0.177,0.208 10 false *5 4.313,3.885 4.49,4.094 0.177,0.208 10 false *5 2.802,5.271 2.979,5.479 0.177,0.208 10 false *5

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
a.
E188997C33
0.76,0.479 1.177,0.729 0.417,0.25 2.625,1.458 2.698,0.677 false 2.625,0.479 2.927,0.667 0.302,0.188 10 false +S 0.177,0.188 0.427,0.385 0.25,0.198 10 false *a 0.885,0.521 1.344,0.719 0.458,0.198 10 false F6
*a Front view of wire harness connector
(to Combination Meter Assembly (Meter Circuit Plate))


Disconnect the F6 combination meter assembly (meter circuit plate) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F6-19 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly (meter circuit plate), the combination meter assembly (meter circuit plate) will output a waveform.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

2.INSPECT COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) (OUTPUT VOLTAGE)

B

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - NO. 8 JUNCTION CONNECTOR)

C

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - NO. 17 JUNCTION CONNECTOR)
2.INSPECT COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) (OUTPUT VOLTAGE)
a.

Reconnect the F6 combination meter assembly (meter circuit plate) connector.


b.
C343117C11
1.49,0.563 1.896,0.833 0.406,0.271 2.479,1.063 2.198,1.656 true 0.188,0.188 0.5,0.385 0.313,0.198 10 false *a 1.583,0.615 1.896,0.813 0.313,0.198 10 false A41 2.5,0.865 2.813,1.063 0.313,0.198 10 false SP1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-11 (SP1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
3.INSPECT SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) (INPUT WAVEFORM)
a.
E262405C33
1.521,0.396 1.896,0.646 0.375,0.25 0.771,1.25 0.448,0.74 false 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 1.635,0.438 2.188,0.75 0.552,0.313 10 false F6 0.333,0.563 0.885,0.875 0.552,0.313 10 false SI 2.948,3.698 3.396,4.021 0.448,0.323 10 false GND 1.292,3.99 1.604,4.198 0.313,0.208 10 false A
*a Component with harness connected
(Combination Meter Assembly (Meter Circuit Plate))


Check the input waveform.

i.

Reconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


ii.

Remove the combination meter assembly (meter circuit plate) with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal F6-20 (SI) and body ground.


iv.

Turn the power switch on (IG).


v.

Turn a wheel slowly.


vi.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Power switch on (IG), wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
a.

Disconnect the F6 combination meter assembly (meter circuit plate) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-20 (SI) - A41-11 (SP1) Always Below 1 Ω
F6-20 (SI) or A41-11 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - NO. 8 JUNCTION CONNECTOR)
a.

Disconnect the F79 No. 8 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-19 (+S) - F79-7 Always Below 1 Ω
F6-19 (+S) or F79-7 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NO. 8 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NO. 8 JUNCTION CONNECTOR)
a.

Check for a short in the wire harness and connectors connected to the No. 8 junction connector shown in the wiring diagram.

HINT:

If voltage is not present, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F79-9 - Body ground*1 Power switch on (IG) 4.5 to 14 V
F79-10 - Body ground*2 Power switch on (IG) 4.5 to 14 V
F79-11 - Body ground Power switch on (IG) 4.5 to 14 V


*1: for 10 Speakers

*2: for Radio and Display Type or Navigation Receiver Type



Result:
Result Proceed to
Voltage is not present in one circuit. A
Voltage is present in all of the circuits. B



A

7.SYSTEM CHECK

B

REPLACE NO. 8 JUNCTION CONNECTOR (INSTRUMENT PANEL WIRE)

7.SYSTEM CHECK
a.

Select the circuit for which voltage was not present in step 6.


Result:
Result System that uses the circuit Proceed to
F79-11 - Body ground Entry and start system A
F79-10 - Body ground Audio and visual system*1 B
Navigation system*2 C
F79-9 - Body ground Navigation system*3 D


*1: for Radio and Display Type

*2: for Navigation Receiver Type

*3: for 10 Speakers



A

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)

B

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)

C

10.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BODY GROUND)

D

11.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)
8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-19 (SPD) or F79-11 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)
a.

Disconnect the F31 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-17 (SPD) or F79-10 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BODY GROUND)
a.

Disconnect the F92 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-17 (SPD) or F79-10 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)
a.

Disconnect the F61 stereo component amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F61-11 (SPD) or F79-9 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - NO. 17 JUNCTION CONNECTOR)
a.

Disconnect the F85 No. 17 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-19 (+S) - F85-16 Always Below 1 Ω
F6-19 (+S) or F85-16 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (NO. 17 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (NO. 17 JUNCTION CONNECTOR)
a.

Check for a short in the wire harness and connectors connected to the No. 17 junction connector shown in the wiring diagram.

HINT:

If voltage is not present, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F85-17 - Body ground*1 Power switch on (IG) 4.5 to 14 V
F85-18 - Body ground*2 Power switch on (IG) 4.5 to 14 V
F85-19 - Body ground Power switch on (IG) 4.5 to 14 V


*1: for 10 Speakers

*2: for Radio and Display Type or Navigation Receiver Type



Result:
Result Proceed to
Voltage is not present in one circuit. A
Voltage is present in all of the circuits. B



A

14.SYSTEM CHECK

B

REPLACE NO. 17 JUNCTION CONNECTOR (INSTRUMENT PANEL WIRE)

14.SYSTEM CHECK
a.

Select the circuit for which voltage was not present in step 13.


Result:
Result System that uses the circuit Proceed to
F85-19 - Body ground Entry and start system A
F85-18 - Body ground Audio and visual system*1 B
Navigation system*2 C
F85-17 - Body ground*3 Audio and visual system*1 or Navigation system*2 D


*1: for Radio and Display Type

*2: for Navigation Receiver Type

*3: for 10 Speakers



A

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)

B

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)

C

10.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BODY GROUND)

D

11.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)