Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0242017 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Skid Control (ABS/VSC/TRAC)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Brake booster with master cylinder assembly branch line or connector

·

Power source circuit of brake booster with master cylinder assembly

·

Brake booster with master cylinder assembly ground circuit

·

Brake booster with master cylinder assembly



WIRING DIAGRAM

C348758E06
0.563,2.688 2.927,3.198 2.365,0.51 10 false No. 2 CAN Junction Connector 0.219,2.688 0.677,2.885 0.458,0.198 10 false F70 1.719,0.313 1.875,0.51 0.156,0.198 10 false 9 1.688,0.906 2,1.104 0.313,0.198 10 false 20 1.708,1.74 1.865,1.938 0.156,0.198 10 false 5 1.667,2.323 1.979,2.521 0.313,0.198 10 false 16 5.365,0.313 5.677,0.51 0.313,0.198 10 false 43 5.365,0.906 5.677,1.104 0.313,0.198 10 false 42 5.677,0.448 6.292,0.646 0.615,0.198 10 false CA1H 5.677,1.031 6.292,1.229 0.615,0.198 10 false CA1L 5.365,1.729 5.677,1.927 0.313,0.198 10 false 30 5.365,2.302 5.677,2.5 0.313,0.198 10 false 29 5.677,1.875 6.292,2.073 0.615,0.198 10 false CA2H 5.677,2.458 6.292,2.656 0.615,0.198 10 false CA2L 1.406,2.948 2.865,3.406 1.458,0.458 10 false from Auxiliary Battery 5.365,2.844 5.677,3.042 0.313,0.198 10 false 15 5.406,3.323 5.719,3.521 0.313,0.198 10 false 5 5.677,2.979 6.135,3.177 0.458,0.198 10 false +BI1 5.677,3.458 6.135,3.656 0.458,0.198 10 false +BI2 3.823,2.792 4.646,3.01 0.823,0.219 10 false ABS NO. 2 3.833,3.281 4.656,3.5 0.823,0.219 10 false ABS NO. 3 3.76,3.792 4.948,4.021 1.188,0.229 10 false ECU-IG1 NO. 2 3.729,4.292 4.917,4.521 1.188,0.229 10 false ECU-IG2 NO. 3 5.667,4 6.125,4.198 0.458,0.198 10 false IG1 5.677,4.479 6.135,4.677 0.458,0.198 10 false IG2 5.365,3.865 5.677,4.063 0.313,0.198 10 false 23 5.406,4.365 5.563,4.563 0.156,0.198 10 false 9 5.365,4.833 5.677,5.031 0.313,0.198 10 false 26 5.365,5.323 5.677,5.521 0.313,0.198 10 false 39 5.667,4.969 6.281,5.167 0.615,0.198 10 false GND1 5.656,5.469 6.271,5.667 0.615,0.198 10 false GND2 1.396,3.969 2.979,4.167 1.583,0.198 10 false from IG1-NO. 1 Relay 1.396,4.458 3.042,4.792 1.646,0.333 10 false from IG2-NO. 2 Relay 5.094,6.115 5.552,6.313 0.458,0.198 10 false A41 5.427,6.115 7.083,6.552 1.656,0.438 10 false Brake Booster with Master Cylinder Assembly 1.406,3.406 2.865,3.865 1.458,0.458 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 61 seconds. Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on and then drive the vehicle at a speed of 20 km/h (12 mph) or more for approximately 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

e.

Check that DTC C1241 which indicates a malfunction in the power source circuit of the electronically controlled brake system is not stored by the electronically controlled brake system.


Result:
Result Proceed to
DTC C1241 is not output A
DTC C1241 is output B



A

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSTIC PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A41 brake booster with master cylinder assembly connector.


c.
C349830C04
1.542,0.146 1.958,0.417 0.417,0.271 1.625,1.656 1.625,0.625 1.625,0.625 1.75,0.625 true 1.531,1.656 1.531,0.625 1.531,0.625 1.396,0.625 true 1.396,2.604 1.531,2.604 1.531,2.604 1.531,1.948 true 1.76,2.604 1.615,2.604 1.615,2.604 1.615,1.948 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.646,0.219 1.958,0.417 0.313,0.198 10 false A41 1.844,0.563 2.396,0.844 0.552,0.281 10 false CA2H 1.01,0.573 1.563,0.854 0.552,0.281 10 false CA2L 1.01,2.552 1.563,2.833 0.552,0.281 10 false CA1L 1.854,2.542 2.406,2.823 0.552,0.281 10 false CA1H
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-43 (CA1H) - A41-42 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A41-30 (CA2H) - A41-29 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349830C07
1.542,0.104 1.958,0.375 0.417,0.271 1.719,1.281 1.719,0.51 1.719,0.51 1.479,0.51 true 1.531,1.542 1.531,0.677 1.531,0.677 1.396,0.677 true 2.156,2.615 2.292,2.615 2.292,2.615 2.292,1.583 true 2.781,2.563 2.635,2.563 2.635,2.563 2.635,1.729 true 2.094,1.281 2.094,0.51 2.094,0.51 2.24,0.51 true 2.635,1.448 2.635,0.583 2.635,0.583 2.781,0.583 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.646,0.156 1.958,0.354 0.313,0.198 10 false A41 1.135,0.438 1.688,0.719 0.552,0.281 10 false +BI2 1.052,0.615 1.604,0.896 0.552,0.281 10 false +BI1 1.896,2.542 2.448,2.823 0.552,0.281 10 false IG1 2.844,2.479 3.396,2.76 0.552,0.281 10 false GND2 2.313,0.438 2.865,0.719 0.552,0.281 10 false IG2 2.854,0.51 3.406,0.792 0.552,0.281 10 false GND1
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-26 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A41-39 (GND2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-5 (+BI2) - Body ground Power switch off 11 to 14 V
A41-15 (+BI1) - Body ground Power switch off 11 to 14 V
A41-9 (IG2) - Body ground Power switch on (IG) 11 to 14 V
A41-23 (IG1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)