Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for LHD)
RM3210E _54 Brake _047517 BRAKE SYSTEM (OTHER) _0243390 BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of brake booster with master cylinder assembly
1.

Bleed air

2.

Clear the data stored during previous linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.

3.

Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light/yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)for Initialization
(Click here)for Calibration
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.



CAUTION / NOTICE / HINT

NOTICE:

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 3.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55735A 4.REMOVE WATER GUARD PLATE LH

Hide 55736D 5.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55701J 6.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 7.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

a.

Using the GTS, perform the accumulator pressure zero down.

i.

Connect the GTS to the DLC3 with the power switch off.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB (Electronically Controlled Brake system) Utility.

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167

iv.

Select "Motor Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.


v.

Perform "Motor Invalid" according to the display on the GTS.


vi.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB (Electronically Controlled Brake system) Utility.

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167

vii.

Select "ECB (Electronically Controlled Brake system) Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.


viii.

Perform "ECB (Electronically Controlled Brake system) Invalid" according to the display on the GTS.


ix.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.



x.

Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down is not complete.



xi.

Turn the GTS off and turn the power switch off.


xii.

Disconnect the GTS from the DLC3.


xiii.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>AUXILIARY BATTERY>REMOVAL



b.

When the accumulator pressure zero down could not be performed using the GTS.

NOTICE:

If DTCs are output, accumulator pressure zero down may not be complete. In this case, perform the following procedure.


i.
C346785C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


With the power switch off, release the lock lever and disconnect the brake booster pump assembly connector as shown in the illustration.


ii.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


iii.

Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down is not complete.



iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>AUXILIARY BATTERY>REMOVAL



Hide 8.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 12601B 9.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 82121 10.DISCONNECT ENGINE WIRE

Hide 82111 11.DISCONNECT ENGINE ROOM MAIN WIRE

a.
C346768

Disconnect the connector from the brake booster with master cylinder assembly.


b.
C347183C01
1.354,2.5 1.594,2.5 true 2.802,2.646 2.875,2.531 2.875,2.531 2.99,2.531 true 2.104,2.99 2.26,2.99 2.26,2.99 2.354,2.813 true 3.01,2.458 3.323,2.615 0.313,0.156 10 false *a 1.958,2.917 2.271,3.073 0.313,0.156 10 false *b 2.198,2.427 2.51,2.583 0.313,0.156 10 false *c 1.625,2.427 1.938,2.583 0.313,0.156 10 false *a
*a Lock Lever
*b Lock Arm
*c Push
V113147

Release the lock lever


Push the lock arm of the connector to release the lock and rotate the lock lever to the position shown in the illustration.


c.
C347184C01
0.865,3.115 0.865,2.896 true 2.396,3.177 2.188,3 2.188,3 1.958,3 true 0.802,3.115 1.115,3.271 0.313,0.156 10 false *a 1.813,2.938 2.125,3.094 0.313,0.156 10 false *b
*a Screwdriver Insertion Point
*b Pre-lock
V113147

Disconnect the connector


Using a screwdriver, release the pre-lock and disconnect the connector from the brake booster with master cylinder assembly as shown in the illustration.


d.

Disengage the clamp to separate the engine room main wire.


Hide 44572C 12.DISCONNECT NO. 2 BRAKE ACTUATOR HOSE

a.
C346771

Slide the clip and disconnect the No. 2 brake actuator hose from the brake booster with master cylinder assembly.


Hide 44551C 13.SEPARATE NO. 1 BRAKE ACTUATOR TUBE

a.
C346762

Remove the nut and separate the No. 1 brake actuator tube from the vehicle body.


Hide 14.SEPARATE BRAKE LINE

a.
C346774

Using a union nut wrench, disconnect the 3 brake lines from the brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




b.
C346776

Disengage the clamp and separate the 3 brake lines.

NOTICE:
·

Do not damage the clamp.

·

Do not kink or damage the brake lines.




Hide 67914 15.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 16.REMOVE COWL SIDE TRIM BOARD LH

Hide 55606 17.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 47101A 18.REMOVE BRAKE PEDAL RETURN SPRING

Hide 47264A 19.REMOVE PUSH ROD PIN

Hide 47210L 20.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C346777C01
0.26,4.063 0.26,3.781 false 0.615,3.583 0.615,3.229 0.615,3.229 0.417,3.229 false 2.51,4.292 2.51,4.01 false 1.375,2.99 1.375,2.635 1.375,2.635 1.177,2.635 false 1.99,3.344 1.99,2.75 1.99,2.75 1.792,2.75 false 2.385,3.417 2.385,2.823 2.385,2.823 2.625,2.823 false 1.021,2.563 1.333,2.719 0.313,0.156 10 false *a 2.656,2.75 2.969,2.906 0.313,0.156 10 false *b 0.208,4.073 0.521,4.229 0.313,0.156 10 false *c 0.26,3.146 0.573,3.302 0.313,0.156 10 false *d 2.458,4.302 2.771,4.458 0.313,0.156 10 false *e 1.656,2.677 1.969,2.833 0.313,0.156 10 false *f
*a Skid Control ECU
*b No. 1 Reservoir Hose
*c Brake Master Cylinder Push Rod Clevis
*d Boot
*e Master Cylinder Reservoir Assembly
*f Brake Actuator Bracket


Remove the 4 nuts and brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.

·

Be careful not to allow any brake fluid to enter the connector.




Hide 44785D 21.REMOVE BRAKE MASTER CYLINDER GASKET