Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2015.11–2016.08
RM3210E _57 Power Source / Network _047550 NETWORKING _0242017 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Clearance Warning ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Clearance Warning ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Clearance Warning (Clearance Sonar)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Clearance Warning (Clearance Sonar)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Clearance Warning (Clearance Sonar)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Clearance Warning ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Clearance warning ECU assembly branch line or connector

·

Power source circuit of clearance warning ECU assembly

·

Clearance warning ECU assembly ground circuit

·

Clearance warning ECU assembly



WIRING DIAGRAM

C250958E98
5.635,0.875 6.146,1.104 0.51,0.229 10 false R1 5.625,1.458 6.135,1.719 0.51,0.26 10 false R2 5.615,2.479 6.083,2.802 0.469,0.323 10 false IG1 5.615,3.063 6.24,3.375 0.625,0.313 10 false E 5.292,0.75 5.521,0.969 0.229,0.219 10 false 17 5.281,1.323 5.49,1.594 0.208,0.271 10 false 18 1.708,0.75 2.24,1.042 0.531,0.292 10 false 3 1.677,1.333 1.948,1.521 0.271,0.188 10 false 13 5.344,2.354 5.542,2.573 0.198,0.219 10 false 1 5.302,2.938 5.688,3.25 0.385,0.313 10 false 30 0.26,1.865 0.781,2.208 0.521,0.344 10 false F68 0.573,1.865 2.719,2.135 2.146,0.271 10 false No. 1 CAN Junction Connector 1.646,2.458 3.167,2.698 1.521,0.24 10 false from IG1-NO. 1 Relay 5.208,4.052 5.719,4.281 0.51,0.229 10 false F26 5.521,4.052 7.021,4.5 1.5,0.448 10 false Clearance Warning ECU Assembly 3.76,2.323 4.76,2.583 1,0.26 10 false ECU-IG1 NO. 4

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 10 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CLEARANCE WARNING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F26 clearance warning ECU assembly connector.


c.
C349834C03
1.49,0.188 1.854,0.438 0.365,0.25 2.948,1.146 2.948,0.302 2.948,0.302 2.802,0.302 true 2.823,1.156 2.823,0.531 2.823,0.531 2.677,0.531 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 1.573,0.25 1.885,0.448 0.313,0.198 10 false F26 2.458,0.479 2.771,0.677 0.313,0.198 10 false R1 2.573,0.25 2.885,0.448 0.313,0.198 10 false R2
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F26-17 (R1) - F26-18 (R2) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349834C04
1.49,0.188 1.854,0.438 0.365,0.25 1.76,1.354 1.76,1.854 1.76,1.854 1.917,1.854 true 0.49,1.135 0.49,0.51 0.49,0.51 0.615,0.51 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 1.573,0.25 1.885,0.448 0.313,0.198 10 false F26 0.698,0.458 1.01,0.656 0.313,0.198 10 false IG1 2.01,1.792 2.323,1.99 0.313,0.198 10 false E
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F26-30 (E) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F26-1 (IG1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)