Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0242017 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "ECM (Engine)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "ECM (Engine)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "ECM Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

ECM main line or connector

·

ECM branch line or connector

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C348680E05
0.281,1.208 0.74,1.406 0.458,0.198 10 false F70 0.552,2.604 3.76,2.802 3.208,0.198 10 false No. 5 CAN Junction Connector 0.26,2.604 0.719,2.802 0.458,0.198 10 false F73 1.677,1.708 1.833,1.906 0.156,0.198 10 false 3 1.656,2.281 1.969,2.479 0.313,0.198 10 false 14 1.677,0.25 2.135,0.448 0.458,0.198 10 false 4 1.646,0.865 2.26,1.063 0.615,0.198 10 false 15 5.24,0.385 5.698,0.583 0.458,0.198 10 false A40 5.24,0.969 5.698,1.167 0.458,0.198 10 false A40 5.281,0.156 5.594,0.354 0.313,0.198 10 false 13 5.292,0.74 5.604,0.938 0.313,0.198 10 false 26 5.24,1.802 5.698,2 0.458,0.198 10 false C31 5.24,2.385 5.698,2.583 0.458,0.198 10 false C31 5.281,1.573 5.594,1.771 0.313,0.198 10 false 31 5.281,2.167 5.594,2.365 0.313,0.198 10 false 32 5.646,1.802 6.26,2 0.615,0.198 10 false CAN+ 5.646,2.396 6.26,2.594 0.615,0.198 10 false CAN- 5.646,0.26 6.26,0.458 0.615,0.198 10 false CANH 5.656,1.115 6.271,1.313 0.615,0.198 10 false CANL 1.385,2.875 2.948,3.146 1.563,0.271 10 false from Auxiliary Battery 3.885,2.74 5.115,2.938 1.229,0.198 10 false EFI-MAIN 3.729,3.219 5.063,3.427 1.333,0.208 10 false ECU-IG2 NO. 1 5.25,2.896 5.708,3.094 0.458,0.198 10 false A40 5.646,2.906 6.26,3.104 0.615,0.198 10 false BATT 5.323,2.677 5.479,2.875 0.156,0.198 10 false 1 5.646,3.396 6.26,3.594 0.615,0.198 10 false IGSW 5.323,3.156 5.479,3.354 0.156,0.198 10 false 6 5.25,3.375 5.708,3.573 0.458,0.198 10 false A40 5.635,3.833 6.094,4.031 0.458,0.198 10 false +B2 5.635,4.302 5.948,4.5 0.313,0.198 10 false +B 5.323,3.615 5.479,3.813 0.156,0.198 10 false 3 5.323,4.073 5.479,4.271 0.156,0.198 10 false 2 5.24,3.833 5.698,4.031 0.458,0.198 10 false A40 5.24,4.281 5.698,4.479 0.458,0.198 10 false A40 1.385,3.354 2.969,3.646 1.583,0.292 10 false from IG2 NO. 1 Relay 1.396,3.813 3.083,4.01 1.688,0.198 10 false from EFI-MAIN Relay 1.521,4.688 3.208,4.885 1.688,0.198 10 false to EFI-MAIN Relay 5.292,4.5 5.604,4.698 0.313,0.198 10 false 46 5.24,4.708 5.698,4.906 0.458,0.198 10 false A40 5.667,4.719 6.281,4.917 0.615,0.198 10 false MREL 5.646,5.167 5.958,5.365 0.313,0.198 10 false EC 5.292,4.948 5.604,5.146 0.313,0.198 10 false 32 5.25,5.156 5.708,5.354 0.458,0.198 10 false A40 5.635,5.667 6.094,5.865 0.458,0.198 10 false E01 5.635,6.156 6.094,6.354 0.458,0.198 10 false E02 5.25,5.656 5.708,5.854 0.458,0.198 10 false C31 5.24,6.146 5.698,6.344 0.458,0.198 10 false C31 5.292,5.427 5.604,5.625 0.313,0.198 10 false 57 5.281,5.927 5.594,6.125 0.313,0.198 10 false 58 5.646,6.677 5.958,6.875 0.313,0.198 10 false E1 5.646,7.177 6.26,7.375 0.615,0.198 10 false ME01 5.281,6.438 5.594,6.635 0.313,0.198 10 false 59 5.281,6.927 5.594,7.125 0.313,0.198 10 false 28 5.24,7.156 5.854,7.49 0.615,0.333 10 false C31 5.24,6.667 5.854,7 0.615,0.333 10 false C31 5.646,7.667 6.104,7.865 0.458,0.198 10 false E04 5.281,7.427 5.594,7.625 0.313,0.198 10 false 26 5.24,7.646 5.854,7.979 0.615,0.333 10 false C31 5.813,8.563 6.375,8.75 0.563,0.188 10 false ECM 0.552,1.208 3.76,1.406 3.208,0.198 10 false No. 2 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE AND BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A40 and C31 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

C349827C03
1.229,0.313 1.625,0.563 0.396,0.25 4.417,0.271 4.823,0.49 0.406,0.219 2.125,1.25 2.125,0.49 2.125,0.49 2.25,0.49 true 2,2.313 2.125,2.313 2.125,2.313 2.125,1.375 true 2.948,1.385 2.948,0.458 2.948,0.458 3.073,0.458 true 3.042,1.385 3.042,0.625 3.042,0.625 3.167,0.625 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 4.51,0.323 4.823,0.521 0.313,0.198 10 false C31 1.323,0.375 1.635,0.573 0.313,0.198 10 false A40 2.333,0.427 2.958,0.635 0.625,0.208 10 false CANH 1.615,2.271 2.24,2.479 0.625,0.208 10 false CANL 3.146,0.385 3.771,0.594 0.625,0.208 10 false CAN+ 3.24,0.552 3.865,0.76 0.625,0.208 10 false CAN-
*a Front view of wire harness connector
(to ECM)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A40-13 (CANH) - A40-26 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
C31-31 (CAN+) - C31-32 (CAN-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK A
NG (No. 2 CAN junction connector main line) B
NG (No. 5 CAN junction connector branch line) C



A

2.CHECK ECM POWER SOURCE CIRCUIT

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM)

C

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (ECM)

2.CHECK ECM POWER SOURCE CIRCUIT

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)