Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0242017 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Combination Meter" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Combination Meter" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Meter circuit plate main line or connector

·

Power source circuit of meter circuit plate

·

Meter circuit plate ground circuit

·

Meter circuit plate



WIRING DIAGRAM

C306931E17
5.656,0.885 6.135,1.042 0.479,0.156 10 false CANH 5.677,1.677 6.156,1.833 0.479,0.156 10 false CANL 5.698,3.156 6.177,3.313 0.479,0.156 10 false B 5.677,2.396 6.156,2.552 0.479,0.156 10 false IG+ 5.677,3.99 6.156,4.146 0.479,0.156 10 false ES 5.344,0.865 5.667,1.063 0.323,0.198 10 false 26 5.344,1.396 5.625,1.594 0.281,0.198 10 false 27 5.354,2.25 5.667,2.438 0.313,0.188 10 false 21 5.354,3.01 5.635,3.208 0.281,0.198 10 false 22 5.365,3.854 5.771,4.052 0.406,0.198 10 false 28 1.583,0.885 1.74,1.083 0.156,0.198 10 false 1 1.552,1.396 1.833,1.594 0.281,0.198 10 false 12 0.26,1.917 0.771,2.208 0.51,0.292 10 false F71 0.552,1.917 2.677,2.271 2.125,0.354 10 false No. 3 CAN Junction Connector 3.885,2.969 5.031,3.146 1.146,0.177 10 false ECU-DCC NO. 2 4.01,2.198 4.917,2.375 0.906,0.177 10 false METER-IG2 1.708,3.115 3.229,3.573 1.521,0.458 10 false from Auxiliary Battery 1.719,2.365 3.479,2.781 1.76,0.417 10 false from IG2-NO. 2 Relay 5.188,4.844 5.771,5.125 0.583,0.281 10 false F6 5.5,4.854 6.875,5.146 1.375,0.292 10 false Meter Circuit Plate

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 20 seconds. Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the LDA main switch on and wait for approximately 52 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (METER CIRCUIT PLATE MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F6 meter circuit plate connector.


c.
C349828C05
1.552,0.615 1.938,0.896 0.385,0.281 1.021,2.625 1.156,2.625 1.156,2.625 1.156,2.125 true 1.448,2.625 1.292,2.625 1.292,2.625 1.292,2.125 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.531,2.563 2.115,2.865 0.583,0.302 10 false CANL 0.594,2.563 1.177,2.865 0.583,0.302 10 false CANH 1.688,0.688 2.271,0.99 0.583,0.302 10 false F6
*a Front view of wire harness connector
(to Meter Circuit Plate)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-26 (CANH) - F6-27 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (METER CIRCUIT PLATE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349828C07
1.552,0.615 1.938,0.896 0.385,0.281 0.375,2.625 0.51,2.625 0.51,2.625 0.51,2.125 true 1.573,2.625 1.417,2.625 1.417,2.625 1.417,2.125 true 0.802,2.625 0.646,2.625 0.646,2.625 0.646,2.125 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 0.875,2.552 1.146,2.75 0.271,0.198 10 false B 0.104,2.552 0.688,2.854 0.583,0.302 10 false IG+ 1.688,0.688 2.271,0.99 0.583,0.302 10 false F6 1.646,2.552 2.229,2.854 0.583,0.302 10 false ES
*a Front view of wire harness connector
(to Meter Circuit Plate)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-28 (ES) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F6-22 (B) - Body ground Power switch off 11 to 14 V
F6-21 (IG+) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)