Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0242017 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Blind Spot Monitor Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Blind Spot Monitor Sensor Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Blind Spot Monitor Master" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Blind Spot Monitor Master" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Blind Spot Monitor Master" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Blind Spot Monitor Sensor Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Blind spot monitor sensor LH branch line or connector

·

Power source circuit of blind spot monitor sensor LH

·

Blind spot monitor sensor LH ground circuit

·

Blind spot monitor sensor LH



WIRING DIAGRAM

C350998E01
0.229,1.844 0.688,2.042 0.458,0.198 10 false M78 0.583,1.844 2.635,2.146 2.052,0.302 10 false No. 7 CAN Junction Connector 1.698,1.333 2.156,1.531 0.458,0.198 10 false 15 1.729,0.75 2.188,0.948 0.458,0.198 10 false 5 5.323,0.729 5.781,0.927 0.458,0.198 10 false 2 5.323,1.323 5.781,1.521 0.458,0.198 10 false 7 5.625,0.875 6.083,1.073 0.458,0.198 10 false CA1P 5.604,2.469 6.063,2.667 0.458,0.198 10 false BLB 5.625,1.458 6.083,1.656 0.458,0.198 10 false CA1N 5.344,2.344 5.802,2.542 0.458,0.198 10 false 5 5.604,3.063 6.063,3.26 0.458,0.198 10 false BLGD 5.292,2.938 5.75,3.135 0.458,0.198 10 false 10 3.708,2.281 4.771,2.542 1.063,0.26 10 false ECU-IG1 NO. 4 1.625,2.469 3.104,2.75 1.479,0.281 10 false from IG1-NO. 1 Relay 5.167,4.094 5.625,4.292 0.458,0.198 10 false M55 5.542,4.083 6.719,4.469 1.177,0.385 10 false Blind Spot Monitor Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait for approximately 12 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (BLIND SPOT MONITOR SENSOR LH BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the M55 blind spot monitor sensor LH connector.


c.
C346738C09
1.469,0.719 1.938,0.938 0.469,0.219 1.063,1.115 1.177,1.115 1.177,1.115 1.51,1.906 true 1.135,3.115 1.25,3.115 1.25,3.115 1.542,2.188 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 1.583,0.76 1.896,0.917 0.313,0.156 10 false M55 0.667,1.042 1.281,1.24 0.615,0.198 10 false CA1P 0.74,3.052 1.354,3.25 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M55-2 (CA1P) - M55-7 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346738C10
1.469,0.719 1.844,0.938 0.375,0.219 2.469,1.115 2.365,1.115 2.365,1.115 2.052,1.906 true 2.552,3.125 2.417,3.125 2.417,3.125 2.052,2.198 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 1.531,0.76 1.844,0.917 0.313,0.156 10 false M55 2.542,1.063 3.156,1.26 0.615,0.198 10 false BLB 2.604,3.073 3.219,3.271 0.615,0.198 10 false BLGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M55-10 (BLGD) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M55-5 (BLB) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)