Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0242017 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Navigation Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Navigation Receiver Assembly Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Display and Navigation (AVN)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Navigation Receiver Assembly Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Navigation receiver assembly branch line or connector

·

Power source circuit of navigation receiver assembly

·

Navigation receiver assembly ground circuit

·

Navigation receiver assembly



WIRING DIAGRAM

C350991E05
0.625,1.906 2.781,2.104 2.156,0.198 10 false No. 4 CAN Junction Connector 0.302,1.906 0.646,2.125 0.344,0.219 10 false F72 5.344,1.271 5.688,1.49 0.344,0.219 10 false 10 5.396,0.708 5.74,0.927 0.344,0.219 10 false 9 1.76,3.563 3.292,3.833 1.531,0.271 10 false from Auxiliary Battery 5.323,0.969 5.667,1.188 0.344,0.219 10 false F92 5.323,1.5 5.667,1.719 0.344,0.219 10 false F92 5.323,2.302 5.667,2.521 0.344,0.219 10 false F92 5.323,2.948 5.667,3.167 0.344,0.219 10 false F93 5.323,3.583 5.667,3.802 0.344,0.219 10 false F93 5.323,4.26 5.667,4.479 0.344,0.219 10 false F93 1.635,0.833 1.979,1.052 0.344,0.219 10 false 1 1.604,1.375 1.948,1.594 0.344,0.219 10 false 12 5.396,2.063 5.74,2.281 0.344,0.219 10 false 1 5.396,2.708 5.74,2.927 0.344,0.219 10 false 3 5.396,3.354 5.74,3.573 0.344,0.219 10 false 4 5.406,4.021 5.75,4.24 0.344,0.219 10 false 7 5.219,4.938 7.125,5.365 1.906,0.427 10 false Navigation Receiver Assembly 2.094,2.927 3.625,3.198 1.531,0.271 10 false from ACC Relay 1.781,2.271 3.313,2.542 1.531,0.271 10 false from IG1-NO. 1 Relay 5.729,0.979 6.313,1.208 0.583,0.229 10 false CANH 5.74,1.5 6.323,1.729 0.583,0.229 10 false CANL 5.729,2.313 6.313,2.542 0.583,0.229 10 false IG 5.74,2.948 6.323,3.177 0.583,0.229 10 false ACC1 5.74,3.583 6.323,3.813 0.583,0.229 10 false +B1 5.75,4.26 6.333,4.49 0.583,0.229 10 false GND1 3.969,2.115 5.094,2.417 1.125,0.302 10 false ECU-IG1 NO. 4 4.135,2.76 5.26,3.063 1.125,0.302 10 false ECU-ACC 4.208,3.385 5.333,3.688 1.125,0.302 10 false RADIO

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 30 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (NAVIGATION RECEIVER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F92 navigation receiver assembly connector.


c.
C287273C36
1.417,0.063 1.896,0.271 0.479,0.208 1.885,1.135 1.875,0.417 1.875,0.417 1.615,0.417 true 2.01,1.135 1.99,0.396 1.99,0.396 2.24,0.396 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 2.302,0.313 2.917,0.51 0.615,0.198 10 false CANL 1.188,0.344 1.802,0.542 0.615,0.198 10 false CANH 1.521,0.083 1.833,0.281 0.313,0.198 10 false F92
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-9 (CANH) - F92-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the F93 navigation receiver assembly connector.


b.
C288171C05
1.521,0.219 1.917,0.469 0.396,0.25 1.521,2.427 1.917,2.688 0.396,0.26 0.958,3.354 0.958,2.854 0.958,2.854 0.813,2.854 true 2.354,1.365 2.354,0.927 2.354,0.927 2.521,0.927 true 2.104,1.354 2.104,0.729 2.104,0.729 2.25,0.729 true 1.76,2.229 1.604,2.229 1.604,2.229 1.604,1.854 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.26 2.063,0.458 0.458,0.198 10 false F93 1.594,2.469 2.052,2.667 0.458,0.198 10 false F92 0.604,2.781 0.917,2.979 0.313,0.198 10 false IG 2.333,0.646 2.948,0.844 0.615,0.198 10 false ACC1 2.615,0.844 3.021,1.073 0.406,0.229 10 false +B1 1.844,2.156 2.375,2.385 0.531,0.229 10 false GND1
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F93-7 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F93-4 (+B1) - Body ground Power switch off 11 to 14 V
F93-3 (ACC1) - Body ground Power switch on (ACC) 11 to 14 V
F92-1 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)