Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0242017 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in Bus 4 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

Airbag ECU assembly

·

No. 2 CAN junction connector

·

No. 5 CAN junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C346831E11
0.854,1.375 1.469,1.573 0.615,0.198 10 false CA2H 0.875,1.906 1.49,2.104 0.615,0.198 10 false CA2L 0.323,1.76 1.094,1.958 0.771,0.198 10 false 120 Ω 6.5,1.76 6.948,1.969 0.448,0.208 10 false 120 Ω 0.052,2.615 1.979,3.417 1.927,0.802 10 false Central Gateway ECU (Network Gateway ECU) 1.344,1.354 1.656,1.552 0.313,0.198 10 false 22 1.365,1.896 1.521,2.094 0.156,0.198 10 false 7 1.781,1.354 1.938,1.552 0.156,0.198 10 false 2 1.729,1.896 2.042,2.094 0.313,0.198 10 false 13 2.063,2.615 3.302,3.052 1.24,0.438 10 false No. 5 CAN Junction Connector 4.031,2.594 5.281,3.104 1.25,0.51 10 false No. 2 CAN Junction Connector 3.271,1.365 3.427,1.563 0.156,0.198 10 false 1 3.24,1.885 3.531,2.125 0.292,0.24 10 false 12 3.76,1.354 3.917,1.552 0.156,0.198 10 false 7 3.708,1.885 4.021,2.083 0.313,0.198 10 false 18 5.26,1.344 5.417,1.542 0.156,0.198 10 false 8 5.229,1.885 5.542,2.083 0.313,0.198 10 false 19 5.688,1.344 6,1.542 0.313,0.198 10 false 13 5.698,1.885 6.01,2.083 0.313,0.198 10 false 22 5.948,2.615 6.698,3.125 0.75,0.51 10 false Airbag ECU Assembly 5.979,1.354 6.594,1.552 0.615,0.198 10 false CANH 5.99,1.896 6.604,2.094 0.615,0.198 10 false CANL 0.063,2.438 0.521,2.635 0.458,0.198 10 false F59 2.052,2.438 2.51,2.635 0.458,0.198 10 false F73 4.052,2.427 4.51,2.625 0.458,0.198 10 false F70 5.938,2.448 6.396,2.646 0.458,0.198 10 false F56

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 20 seconds. Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on and then drive the vehicle at a speed of 20 km/h (12 mph) or more for approximately 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F73 No. 5 CAN junction connector.


c.
C348627C20
1.438,0.094 1.865,0.354 0.427,0.26 0.688,1.802 0.688,0.552 0.688,0.552 0.948,0.552 true 0.698,2.125 0.698,3.177 0.698,3.177 0.969,3.177 true 0.896,1.833 0.896,0.823 0.896,0.823 1.188,0.823 true 0.906,2.125 0.906,2.854 0.906,2.854 1.25,2.854 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.552,0.177 1.865,0.375 0.313,0.198 10 false F73 1,0.5 1.594,0.667 0.594,0.167 10 false CANH*b 1.031,3.115 1.625,3.281 0.594,0.167 10 false CANL*b 1.24,0.76 1.833,0.927 0.594,0.167 10 false CANH*c 1.302,2.802 1.906,2.938 0.604,0.135 10 false CANL*c
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F73-1 (CANH) - F73-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 2 CAN junction connector
F73-2 (CANH) - F73-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 2 CAN junction connector) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

2.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 5 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
2.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the F73 No. 5 CAN junction connector.


b.

Disconnect the F59 central gateway ECU (network gateway ECU) connector.


c.
C326490C72
1.531,0.135 1.906,0.365 0.375,0.229 2.417,0.917 2.417,0.313 2.417,0.313 2.552,0.313 true 2.323,1.208 2.323,1.854 2.323,1.854 2.469,1.854 true 0.104,0.063 0.417,0.219 0.313,0.156 10 false *a 2.542,1.792 2.979,1.938 0.438,0.146 10 false CA2H 1.625,0.188 2,0.333 0.375,0.146 10 false F59 2.635,0.26 3.073,0.406 0.438,0.146 10 false CA2L
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F59-22 (CA2H) - F59-7 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 5 CAN JUNCTION CONNECTOR)

3.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the F73 No. 5 CAN junction connector.


b.

Disconnect the F70 No. 2 CAN junction connector.


c.
C348627C46
1.49,0.292 1.917,0.552 0.427,0.26 2.125,1.802 2.125,0.792 2.125,0.792 2.281,0.792 true 2.135,2.135 2.135,2.865 2.135,2.865 2.281,2.865 true 1.927,1.802 1.927,0.792 1.927,0.792 1.76,0.792 true 1.938,2.135 1.938,2.865 1.938,2.865 1.792,2.865 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.594,0.365 1.906,0.563 0.313,0.198 10 false F70 1.208,0.729 1.802,0.896 0.594,0.167 10 false CANH*b 1.25,2.802 1.844,2.969 0.594,0.167 10 false CANL*b 2.354,0.729 2.948,0.896 0.594,0.167 10 false CANH*c 2.354,2.802 2.948,2.969 0.594,0.167 10 false CANL*c
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 5 CAN Junction Connector
*c to Airbag ECU Assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F70-7 (CANH) - F70-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 5 CAN junction connector
F70-8 (CANH) - F70-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Airbag ECU assembly



Result:
Result Proceed to
OK A
NG (Line to No. 5 CAN junction connector) B
NG (Line to Airbag ECU assembly) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR OPEN IN CAN MAIN BUS LINES (AIRBAG ECU ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN CAN MAIN BUS LINES (AIRBAG ECU ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the F70 No. 2 CAN junction connector.


b.

Disconnect the F56 airbag ECU assembly connector.


c.
C349835C01
1.438,0.094 1.844,0.333 0.406,0.24 1.427,1.094 1.427,0.51 1.427,0.51 1.563,0.51 true 1.427,1.865 1.302,1.865 1.302,1.865 1.302,1.448 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.635,0.448 2.115,0.688 0.479,0.24 10 false CANH 1.51,1.802 1.99,2.042 0.479,0.24 10 false CANL 1.542,0.156 2.021,0.396 0.479,0.24 10 false F56
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F56-13 (CANH) - F56-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (AIRBAG ECU ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)