Home › Drivetrain › P610 HYBRID TRANSMISSION / TRANSAXLE › ELECTRONIC SHIFT LEVER SYSTEM
RM3210E _52 Drivetrain _047503 P610 HYBRID TRANSMISSION / TRANSAXLE _0243554 ELECTRONIC SHIFT LEVER SYSTEM J

P610 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  "P" Position Switch Indicator Light Circuit  


DESCRIPTION

The P position switch (transmission shift main switch) indicator light comes on when the P position switch (transmission shift main switch) is pressed (park (P) is selected), goes off when a shift state other than park (P) is selected and blinks when a system malfunction occurs. A warning message will also be displayed on the multi-information display if a malfunction occurs.

WIRING DIAGRAM

C338785E03
4.729,3.063 6.563,3.542 1.833,0.479 10 false Hybrid Vehicle Control ECU 4.729,2.917 5.073,3.177 0.344,0.26 10 false F3 5.042,2.333 5.385,2.594 0.344,0.26 10 false P1 4.781,1.115 5.125,1.375 0.344,0.26 10 false 39 5.052,1.208 5.396,1.469 0.344,0.26 10 false IND 4.781,2.177 5.125,2.438 0.344,0.26 10 false 13 3.896,1.094 4.146,1.365 0.25,0.271 10 false 7 3.906,0.698 4.25,0.958 0.344,0.26 10 false 6 2.771,1.094 3.021,1.365 0.25,0.271 10 false 2 2.771,0.677 3.021,0.948 0.25,0.271 10 false 4 2.458,1.646 4.469,2.448 2.01,0.802 10 false P Position Switch (Transmission Shift Main Switch) 2.438,1.469 2.781,1.729 0.344,0.26 10 false F53 2.948,1.208 3.198,1.479 0.25,0.271 10 false E 2.927,0.771 3.177,1.042 0.25,0.271 10 false S 3.51,0.802 3.885,1.115 0.375,0.313 10 false IND+ 3.531,1.208 3.938,1.49 0.406,0.281 10 false IND- 0.573,0.5 1.542,0.885 0.969,0.385 10 false ECU-B NO. 1

PROCEDURE

1.CHECK P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) (INDICATOR LIGHT)
a.

Turn the power switch on (IG).


b.

Depress the brake pedal and select neutral (N).


c.

Operate the P position switch (transmission shift main switch) and check the condition of the indicator light.


Result:
Condition of Indicator Light Proceed to
Indicator light illuminates A
Indicator light does not come on. B


d.

Turn the power switch off.



A

2.CHECK P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) (INDICATOR LIGHT)

B

4.CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) POWER SOURCE CIRCUIT)
2.CHECK P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) (INDICATOR LIGHT)
a.

Disconnect the F3 hybrid vehicle control ECU connector.


b.

Turn the power switch on (IG).


c.

Inspect the P position switch (transmission shift main switch) indicator light condition.

Result:
Result Proceed to
Indicator light does not go off. (Remains on) A
Indicator light goes off. B


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Reconnect the F3 hybrid vehicle control ECU connector.



A

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH))

B

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH))
a.

Disconnect the F3 hybrid vehicle control ECU connector.


b.

Disconnect the F53 P position switch (transmission shift main switch) connector.


c.
C338792C02
1.521,2.656 1.927,2.927 0.406,0.271 1.417,0.344 1.844,0.625 0.427,0.281 2.677,2.354 2.521,1.813 true 2.125,4.094 2.073,3.708 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 2.042,4.135 2.469,4.406 0.427,0.271 10 false IND- 0.177,2.875 0.49,3.073 0.313,0.198 10 false *b 2.615,2.396 3.042,2.667 0.427,0.271 10 false IND 1.604,2.719 2.031,2.99 0.427,0.271 10 false F53 1.531,0.417 1.958,0.688 0.427,0.271 10 false F3
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F3-39 (IND) or F53-7 (IND-) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the F53 P position switch (transmission shift main switch) connector.


e.

Reconnect the F3 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

REPLACE P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) POWER SOURCE CIRCUIT)
a.

Disconnect the F53 P position switch (transmission shift main switch) connector.


b.
C208992C27
0.396,0.938 0.813,1.177 0.417,0.24 1.958,1.323 2.333,1.74 true 0.094,0.031 0.313,0.229 0.219,0.198 10 false *a 2.281,1.792 2.667,2.042 0.385,0.25 10 false IND+ 0.49,1 0.823,1.219 0.333,0.219 10 false F53
*a Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F53-6 (IND+) - Body ground Power switch off 9 to 14 V



c.

Reconnect the F53 P position switch (transmission shift main switch) connector.


Result:
Proceed to
OK
NG



OK

5.INSPECT P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH)

NG

CHECK AND REPAIR POWER SOURCE CIRCUIT

5.INSPECT P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH)
a.

Disconnect the F53 P position switch (transmission shift main switch) connector.


b.
A216509C14
1.354,1.104 1.052,0.51 true 1.521,1.094 1.844,0.5 true 2.292,1.094 2.146,1.26 false 1.302,1.094 1.167,1.26 false 0.052,0.094 0.229,0.281 0.177,0.188 10 false *a 0.854,0.354 1.177,0.521 0.323,0.167 10 false IND- 1.792,0.354 2.115,0.521 0.323,0.167 10 false IND+
*a Component without harness connected
(P Position Switch (Transmission Shift Main Switch))


Apply auxiliary battery voltage between terminals F53-6 (IND+) and F53-7 (IND-) and check the indicator light.

Result:
Condition Specified Condition
Auxiliary battery voltage applied between terminals F53-6 (IND+) and F53-7 (IND-) Comes on


HINT:

Terminals 1 and 8 of the P position switch (transmission shift main switch) side connector are empty.



c.

Reconnect the F53 P position switch (transmission shift main switch) connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH))

NG

REPLACE P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH)

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH))
a.

Disconnect the F3 hybrid vehicle control ECU connector.


b.

Disconnect the F53 P position switch (transmission shift main switch) connector.


c.
C338792C03
1.521,2.656 1.927,2.927 0.406,0.271 1.417,0.344 1.844,0.625 0.427,0.281 2.677,2.354 2.521,1.813 true 2.125,4.094 2.073,3.708 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 2.042,4.135 2.469,4.406 0.427,0.271 10 false IND- 0.177,2.875 0.49,3.073 0.313,0.198 10 false *b 2.615,2.396 3.042,2.667 0.427,0.271 10 false IND 1.615,2.719 2.042,2.99 0.427,0.271 10 false F53 1.531,0.406 1.958,0.677 0.427,0.271 10 false F3
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F3-39 (IND) - F53-7 (IND-) Power switch off Below 1 Ω



d.

Reconnect the F53 P position switch (transmission shift main switch) connector.


e.

Reconnect the F3 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR