Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3210E _59 Vehicle Exterior _047533 LIGHTING (EXT) _0244228 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog lights.

WIRING DIAGRAM

E333229E05
5.417,4.885 7.063,5.385 1.646,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 3.281,4.427 5.969,4.74 2.688,0.313 10 false Instrument Panel Junction Block Assembly 6.115,4 6.531,4.177 0.417,0.177 10 false RFGO 5.854,3.99 6.104,4.188 0.25,0.198 10 false 27 4.5,3.729 5.052,3.927 0.552,0.198 10 false FOG RR 3.438,3.042 3.667,3.219 0.229,0.177 10 false 3H 3.448,2.854 3.646,3.031 0.198,0.177 10 false 21 1.292,3.552 2.875,3.938 1.583,0.385 10 false Rear Light Assembly RH 1.292,3.406 1.646,3.594 0.354,0.188 10 false P7 2.563,2.958 2.802,3.167 0.24,0.208 10 false 2 2.385,2.958 2.625,3.167 0.24,0.208 10 false B 1.531,2.958 1.771,3.167 0.24,0.208 10 false E 1.354,2.958 1.594,3.167 0.24,0.208 10 false 1 4.5,2.438 5.063,2.615 0.563,0.177 10 false FOG RR 4.625,1.688 4.979,1.875 0.354,0.188 10 false TAIL 6.115,0.948 6.521,1.104 0.406,0.156 10 false TRLY 2.146,1.198 2.771,1.385 0.625,0.188 10 false J/B-AM 0.042,1.021 1.417,1.354 1.375,0.333 10 false from Auxiliary Battery 3.438,1.031 3.75,1.229 0.313,0.198 10 false 3K 3.479,0.844 3.719,1.052 0.24,0.208 10 false 1 5.875,0.948 6.125,1.146 0.25,0.198 10 false 14 5.323,1.552 5.677,1.74 0.354,0.188 10 false TAIL 1.26,4.698 1.615,4.885 0.354,0.188 10 false P8 1.542,4.219 1.781,4.427 0.24,0.208 10 false E 2.396,4.219 2.635,4.427 0.24,0.208 10 false B 2.573,4.208 2.813,4.417 0.24,0.208 10 false 2 1.365,4.219 1.604,4.427 0.24,0.208 10 false 1 1.563,3.198 2.688,3.531 1.125,0.333 10 false Rear Fog Light 1.26,4.854 2.844,5.24 1.583,0.385 10 false Rear Light Assembly LH 1.521,4.479 2.646,4.813 1.125,0.333 10 false Rear Fog Light

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Fog Light Relay Rear fog lights ON/OFF Light control switch in tail position
Body Electrical > Main Body > Active Test
Tester Display
Rear Fog Light Relay
50004 123 17
OK:

Rear fog light relay operates. (Rear fog lights come on.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the P7 rear light assembly RH connector.


b.

Disconnect the P8 rear light assembly LH connector.


c.

Disconnect the 3H instrument panel junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3H-21 - P7-2 (B) Always Below 1 Ω
3H-21 - P8-2 (B) Always Below 1 Ω
3H-21 or P7-2 (B) - Body ground Always 10 kΩ or higher
3H-21 or P8-2 (B) - Body ground Always 10 kΩ or higher
P7-1 (E) - Body ground Always Below 1 Ω
P8-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Connect a positive (+) lead from the auxiliary battery to terminal 3K-1.


d.

Connect a negative (-) lead from the auxiliary battery to terminal MB-14 (TRLY) and MB-27 (RFGO).


e.

Measure the voltage according to the value(s) in the table below.

E344404C02
3.323,2.135 3.677,2.365 0.354,0.229 5.021,0.25 5.354,0.49 0.333,0.24 2.063,0.302 2.385,0.542 0.323,0.24 3.052,3.375 3.281,2.885 false 5.031,3.333 4.792,2.875 false 2.885,3.406 3.292,3.604 0.406,0.198 10 false TRLY 4.896,3.385 5.563,3.594 0.667,0.208 10 false RFGO 3.385,2.177 3.698,2.375 0.313,0.198 10 false MB 5.094,0.302 5.406,0.5 0.313,0.198 10 false 3H 2.135,0.344 2.448,0.542 0.313,0.198 10 false 3K 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
3H-21 - Negative (-) auxiliary battery terminal Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY