Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3210E _59 Vehicle Exterior _047533 LIGHTING (EXT) _0244228 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay.

WIRING DIAGRAM

E333127E06
5.417,2.854 7.052,3.281 1.635,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 5.417,2.708 5.729,2.906 0.313,0.198 10 false MB 3.25,2.177 6.104,2.385 2.854,0.208 10 false Instrument Panel Junction Block Assembly 6.292,0.448 6.698,0.615 0.406,0.167 10 false TRLY 6.042,0.448 6.281,0.656 0.24,0.208 10 false 14 5.26,1.094 5.604,1.292 0.344,0.198 10 false TAIL 4.521,1.219 4.875,1.396 0.354,0.177 10 false TAIL 2.104,0.708 2.698,0.917 0.594,0.208 10 false J/B-AM 0.115,1.719 2.396,2.115 2.281,0.396 10 false to Taillights and License Plate Lights 0.385,0.542 1.24,1 0.854,0.458 10 false from Auxiliary Battery 3.292,0.552 3.563,0.74 0.271,0.188 10 false 3K 3.292,1.729 3.542,1.906 0.25,0.177 10 false 3H 3.292,1.531 3.531,1.729 0.24,0.198 10 false 30 3.323,0.365 3.521,0.583 0.198,0.219 10 false 1


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Taillight Relay Taillight relay ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Taillight Relay
50004 123 13
OK:

Taillight relay operates. (Taillights illuminate.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3K instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3K-1 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Connect a positive (+) lead from the auxiliary battery to terminal 3K-1.


d.

Connect a negative (-) lead from the auxiliary battery to terminal MB-14 (TRLY).


e.

Measure the voltage according to the value(s) in the table below.

E344404C03
2.042,0.333 2.417,0.583 0.375,0.25 3.292,2.167 3.667,2.417 0.375,0.25 4.958,0.25 5.333,0.5 0.375,0.25 3.052,3.375 3.281,2.885 false 2.885,3.406 3.292,3.604 0.406,0.198 10 false TRLY 3.375,2.208 3.688,2.406 0.313,0.198 10 false MB 5.052,0.292 5.365,0.49 0.313,0.198 10 false 3H 2.146,0.385 2.458,0.583 0.313,0.198 10 false 3K 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
3H-30 - Negative (-) auxiliary battery terminal Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY