Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING
RM3210E _59 Vehicle Exterior _047530 SLIDING ROOF / CONVERTIBLE _0244347 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  INSTALLATION  


PROCEDURE

Hide 1.INSTALL SLIDING ROOF HOUSING ASSEMBLY

a.

Loosen the 4 bolts of the brackets of the sliding roof housing assembly.


b.

Temporarily install the sliding roof housing assembly with the 6 nuts and 4 bolts.

B432072N03
2.76,1.177 2.917,1.375 0.156,0.198 10 true 1 4.729,2.396 4.885,2.594 0.156,0.198 10 false 2


c.

Tighten the 2 nuts.

HINT:

Tighten the 2 nuts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Tighten the 4 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Tighten the 8 bolts to install the sliding roof housing assembly.

B432073C02
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


HINT:

The brackets can be installed in any order. The bolts must be tightened in the order of (A) then (B).


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 63240A 2.CONNECT SLIDING ROOF DRAIN HOSE ASSEMBLY LH

a.
B432069C01
0.417,2.208 3,3.333 2.583,1.125 2.656,0.729 3,0.583 false 2.542,0.708 2.833,0.333 false 2.219,2.542 2.625,2.417 false 2.854,0.25 3.167,0.406 0.313,0.156 10 false *a 3.021,0.5 3.333,0.656 0.313,0.156 10 false *b 2.646,2.354 2.958,2.51 0.313,0.156 10 false *c
*a Clamp
*b Marking
*c Lock


Connect the sliding roof drain hose assembly LH.

HINT:

Slide the hose to the base of the drain pipe.



b.

Engage the claw to secure the sliding roof drain hose assembly LH.

HINT:
·

Make sure that the clamp is on the marking or between the marking and hose end.

·

Make sure that the lock of the clamp is facing up.




Hide 63220A 3.CONNECT SLIDING ROOF DRAIN HOSE ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 63249E 4.CONNECT SLIDING ROOF DRAIN HOSE

HINT:
·

Use the same procedure as for the sliding roof drain hose assembly LH.

·

Use the same procedure for both sliding roof drain hoses.



Hide 63251K 5.INSTALL SLIDING ROOF WEATHERSTRIP

a.

Position the joint of the sliding roof weatherstrip in the center of the rear side of the sliding roof panel sub-assembly as shown in the illustration.

B432074C01
1.792,3.646 2.031,3.438 false 4.573,2.188 4.813,1.854 false 6.542,2.219 6.677,1.917 false 5.51,2.219 5.75,1.885 false 0.563,0.656 0.802,0.74 true 3.313,0.729 3.552,0.646 true 0.5,0.917 0.906,0.833 true 3.229,0.833 3.646,0.917 true 0.896,0.938 1.208,1 1.208,1 1.01,0.802 true 3.229,0.927 2.875,0.979 2.875,0.979 3.094,0.813 true 1.635,3.583 1.948,3.74 0.313,0.156 10 false *a 0.406,0.594 0.719,0.75 0.313,0.156 10 false *b 0.354,0.844 0.667,1 0.313,0.156 10 false *c 1.229,0.948 1.542,1.104 0.313,0.156 10 false *d 4.083,0.583 4.396,0.74 0.313,0.156 10 false *e 4.104,1.667 4.417,1.823 0.313,0.156 10 false *f 4.833,1.792 5.146,1.948 0.313,0.156 10 false *g 5.771,1.833 6.083,1.99 0.313,0.156 10 false *h 6.708,1.854 7.021,2.01 0.313,0.156 10 false *i 3.583,0.594 3.896,0.75 0.313,0.156 10 false *b 3.667,0.865 3.979,1.021 0.313,0.156 10 false *c 2.719,0.917 3.031,1.073 0.313,0.156 10 false *d
*a Joint *b Alignment Mark (Red)
*c Middle Mark *d Mark
*e Correct *f Incorrect
*g Pinched *h Exposed
*i Gap (raised, wavy, etc.) - -
V100136

Front Side - -



b.

Align each alignment mark (red) on the sliding roof weatherstrip with the middle mark in the front corners of the sliding roof panel sub-assembly and install the sliding roof weatherstrip.

HINT:
·

Make sure that the joint of the sliding roof weatherstrip is positioned in the center of the rear side of the sliding roof panel sub-assembly.

·

Make sure that each alignment mark (red) on the sliding roof weatherstrip is positioned between the marks of the sliding roof panel sub-assembly.

·

Make sure that the lip of the sliding roof weatherstrip is securely installed.




Hide 63201G 6.INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

a.

Using a T25 "TORX" socket wrench, temporarily install the sliding roof glass sub-assembly with the 4 screws.


b.

Perform a level check.

B432075N01
4.604,1.313 4.76,1.51 0.156,0.198 10 false a 1.427,1.583 1.563,1.74 0.135,0.156 10 true A 1.667,1.583 1.802,1.74 0.135,0.156 10 true A 2.094,1.219 2.229,1.375 0.135,0.156 10 true C 2.083,1.448 2.219,1.604 0.135,0.156 10 true C 2.042,2.083 2.177,2.24 0.135,0.156 10 true B 2.281,2.083 2.417,2.24 0.135,0.156 10 true B 1.802,2.385 1.938,2.542 0.135,0.156 10 true D 1.906,2.573 2.042,2.729 0.135,0.156 10 true D

i.

Check the difference in level "a" between the roof panel and the upper surface of the sliding roof weatherstrip when the sliding roof glass sub-assembly is fully closed.

HINT:

"+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.


Standard:
Area Measurement Area Measurement
A - A 0 + 1.0 mm (0 + 0.0394 in.)
0 - 2.0 mm (0 - 0.0787 in.)
B - B 0 + 2.0 mm (0 + 0.0787 in.)
0 - 1.0 mm (0 - 0.0394 in.)
C - C 0 + 1.5 mm (0 + 0.0591 in.)
0 - 1.5 mm (0 - 0.0591 in.)
D - D 0 + 1.5 mm (0 + 0.0591 in.)
0 - 1.0 mm (0 - 0.0394 in.)




c.
B432076C01
1.896,1.448 2.208,1.604 0.313,0.156 10 false *a
*a Even


Perform a gap check.

i.

Check the gap between the roof panel and sliding roof glass sub-assembly.

NOTICE:

The gap must be even all around.




d.

After adjusting the sliding roof glass sub-assembly, using a T25 "TORX" socket wrench, install the sliding roof glass sub-assembly with the 4 screws.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 7.CHECK FOR WATER LEAK

a.

After adjusting the sliding roof glass sub-assembly, check for water leakage into the vehicle interior.


b.

If there are any leaks, readjust the sliding roof glass sub-assembly.


Hide 62180A 8.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

Hide 62170A 9.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 63218G 10.INSTALL SLIDING ROOF SIDE GARNISH LH

a.

Engage the 2 claws to install the sliding roof side garnish LH.


Hide 63217G 11.INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.