Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0230369 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 62180A 1.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY

NOTICE:

When installing a curtain shield airbag assembly, have assistants hold it to prevent it from bending.


a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B432336C01
2.167,0.333 2.323,0.333 2.323,0.333 2.604,0.646 true 1.156,1.948 1.313,1.948 1.313,1.948 1.594,2.26 true 0.969,1.865 1.167,2.063 0.198,0.198 10 true *a 2,0.25 2.198,0.438 0.198,0.188 10 false *b
*a Airbag Connector
*b Airbag Connector Lock


Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



d.

Push in the airbag connector lock to install the airbag connector.


e.

Insert the 3 hooks to temporarily install the curtain shield airbag assembly.

B434296C01
1.708,2.875 1.99,3.229 1.99,3.229 2.177,3.229 true 3.25,4.094 3.531,4.448 3.531,4.448 3.719,4.448 true 3.729,2.875 3.979,2.875 true 5.281,4.167 5.531,4.167 true 5.396,0.875 6.958,0.875 6.958,0.875 6.958,2.5 true 5.906,1.865 5.906,0.875 true 1.375,0.115 1.615,0.344 0.24,0.229 10 true *A 2.094,1.802 2.24,1.99 0.146,0.188 10 true 1 4.01,2.802 4.323,2.958 0.313,0.156 10 false *1 2.219,3.167 2.531,3.323 0.313,0.156 10 false *2 0.5,2.219 0.813,2.375 0.313,0.156 10 false *a 2.094,3.531 2.406,3.688 0.313,0.156 10 false *b 1.333,1.333 1.531,1.531 0.198,0.198 10 true *c 5.229,0.792 5.438,1.01 0.208,0.219 10 false *d 3.76,4.375 4.073,4.531 0.313,0.156 10 false *2 5.552,4.083 5.865,4.24 0.313,0.156 10 false *1 3.094,1.146 3.292,1.344 0.198,0.198 10 true *c 5.625,1.458 5.823,1.656 0.198,0.198 10 true *c 2.396,1.76 2.542,1.948 0.146,0.188 10 true 2 0.583,1.229 0.729,1.417 0.146,0.188 10 true 3 5.625,1.885 5.771,2.073 0.146,0.188 10 true 4 1.698,1.427 1.865,1.604 0.167,0.177 10 true *a 4.469,1.24 4.635,1.417 0.167,0.177 10 true *a 4.906,1.323 5.073,1.5 0.167,0.177 10 true *a 5.99,1.781 6.156,1.958 0.167,0.177 10 true *a 3.74,1.188 3.917,1.375 0.177,0.188 10 true *b 6.896,2.583 7.073,2.771 0.177,0.188 10 true *b 2.083,0.792 2.229,0.979 0.146,0.188 10 true 1 2.344,0.792 2.49,0.979 0.146,0.188 10 true 2
*A w/o Occupant Classification System - -
*1 Pin *2 Spacer
*a Clip (A) *b Clip (B)
*c Clip (C) *d Spacer Location



f.

Install 3 new bolts and engage the clip (C) in the order shown in the illustration.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Do not twist the curtain shield airbag assembly when installing it.



g.

Install the curtain shield airbag assembly with 2 new spacers, 4 new clips (A) with pins and 2 new clips (B) with pins, and engage the 2 clips (C).

NOTICE:

Do not twist the curtain shield airbag assembly when installing it.


HINT:

Engage the 2 claws to install each new clip (A) and (B).



h.

Using needle nose pliers, push the 6 pins into the 4 clips (A) and 2 clips (B).

NOTICE:
·

Do not damage the pins.

·

Make sure that the pins of the clips (A) and (B) are pushed in firmly.




Hide 2.INSTALL ROOF HEADLINING ASSEMBLY

Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION