Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM3210E _58 Vehicle Interior _047534 HEATING / AIR CONDITIONING _0244634 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B14B2  Lost Communication with Front Panel LIN  


DESCRIPTION

The air conditioning control assembly communicates with the air conditioning amplifier assembly via LIN communication.

If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate even if the air conditioning control assembly is operated.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B14B2 Lost Communication with Front Panel LIN Lost communication with air conditioning control assembly
·

Harness or connector between air conditioning control assembly and IG power source

·

Harness or connector between air conditioning control assembly and body ground

·

LIN communication system

·

Air conditioning control assembly

·

Air conditioning amplifier assembly


Memorized
(10 sec. or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E282266E22
1.635,0.875 2.25,1.073 0.615,0.198 10 false LIN1 1.698,1.406 2.313,1.604 0.615,0.198 10 false IG+ 1.625,1.927 2.24,2.125 0.615,0.198 10 false GND 2.021,1.313 2.396,1.542 0.375,0.229 10 false 8 2.01,1.823 2.604,2.094 0.594,0.271 10 false 1 2.625,1.552 3.688,1.844 1.063,0.292 10 false ECU-IG1 NO. 4 3.885,1.406 4.854,1.833 0.969,0.427 10 false from IG1-NO. 1 Relay 4.76,2.51 7.104,2.875 2.344,0.365 10 false Air Conditioning Amplifier Assembly 4.771,2.333 5.385,2.531 0.615,0.198 10 false F58 5.24,0.885 5.854,1.083 0.615,0.198 10 false LIN1 2.021,0.719 2.635,0.917 0.615,0.198 10 false 6 4.99,0.698 5.604,0.896 0.615,0.198 10 false 14 0.5,2.542 2.844,2.906 2.344,0.365 10 false Air Conditioning Control Assembly 0.51,2.375 1.125,2.573 0.615,0.198 10 false F52 0.938,3.198 2.729,3.479 1.792,0.281 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - IG POWER SOURCE)
a.

Disconnect the F52 air conditioning control assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F52-8 (IG+) - Body ground Power switch on (IG) 11 to 14 V
F52-8 (IG+) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F52-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - AIR CONDITIONING CONTROL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - AIR CONDITIONING CONTROL ASSEMBLY)
a.

Disconnect the F58 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F52-6 (LIN1) - F58-14 (LIN1) Always Below 1 Ω
F52-6 (LIN1) or F58-14 (LIN1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Reconnect the F58 air conditioning amplifier assembly connector.


b.

Turn the power switch on (IG).


c.
E334619N03
0.302,1.563 0.76,1.76 0.458,0.198 10 false GND

Connect an oscilloscope to terminals F58-14 (LIN1) and F58-4 (GND) of the air conditioning amplifier assembly and check the waveform.

OK:

Waveform is similar to that shown in the illustration.


Item Content
Tool Setting 2 V/DIV., 20 ms./DIV.
Vehicle Condition Power switch on (IG)


Result:
Proceed to
OK
NG



OK

5.INSPECT AIR CONDITIONING CONTROL ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

5.INSPECT AIR CONDITIONING CONTROL ASSEMBLY
a.

Reconnect the F52 air conditioning control assembly connector.


b.

Turn the power switch on (IG).


c.
E334626C02
1.458,0.458 1.844,0.677 0.385,0.219 1.698,1.542 1.115,2.198 false 1.823,1.396 2.25,2.115 false 0.385,4.042 0.844,4.24 0.458,0.198 10 false GND 0.938,2.25 1.552,2.448 0.615,0.198 10 false LIN1 0.229,0.167 0.542,0.365 0.313,0.198 10 false *a 1.552,0.5 2.01,0.698 0.458,0.198 10 false F52 2.167,2.188 2.781,2.385 0.615,0.198 10 false GND
*a Component with harness connected
(Air Conditioning Control Assembly)


Connect an oscilloscope to terminals F52-6 (LIN1) and F52-1 (GND) of the air conditioning control assembly and check the waveform.

OK:

Waveform is similar to that shown in the illustration.


Item Content
Tool Setting 2 V/DIV., 20 ms./DIV.
Vehicle Condition Power switch on (IG)


Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AIR CONDITIONING CONTROL ASSEMBLY