Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM
RM3210E _58 Vehicle Interior _047507 THEFT DETERRENT / KEYLESS ENTRY _0244661 IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  B2779  Engine Starter Communication Malfunction  


DESCRIPTION

When an internal malfunction occurs in the certification ECU (smart key ECU assembly), the certification ECU (smart key ECU assembly) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2779 Engine Starter Communication Malfunction An internal malfunction occurs in the certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) DTC output confirmation operation:

Always



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
- -

Related Data List and Active Test
DTC No. Data List and Active Test
B2779 -

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check for CAN communication system DTCs.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

OK:

CAN communication DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (WIRELESS C CODE)

NG

GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

2.READ VALUE USING GTS (WIRELESS C CODE)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wireless C Code Registration status between remote engine starter ECU and certification ECU (smart key ECU assembly) No Regd or Regd No Regd: Remote starter ID not registered to remote engine start ECU and certification ECU (smart key ECU assembly)
Regd: Remote starter ID registered to remote engine start ECU and certification ECU (smart key ECU assembly)
Problems may be caused by the following:
·

DTC B2779 is stored.

·

Remote engine start ECU registration has not been performed.

·

Malfunctions in the certification ECU (smart key ECU assembly) or remote engine start ECU.


Body Electrical > Entry&Start > Data List
Tester Display
Wireless C Code
50003 125 44

Result:
Result Proceed to
"No Regd" is displayed on the GTS A
"Regd" is displayed on the GTS B



A

3.REGISTER REMOTE ENGINE STARTER ID

B

5.REPLACE REMOTE ENGINE STARTER ECU
3.REGISTER REMOTE ENGINE STARTER ID
a.

Register the remote engine starter ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

4.CHECK REMOTE ENGINE STARTER FUNCTION
4.CHECK REMOTE ENGINE STARTER FUNCTION
a.

Check the remote engine starter function.

OK:

Remote engine starter functions operate normally.



Result:
Proceed to
OK
NG



OK

END (REMOTE ENGINE STARTER ID WAS NOT REGISTERED)

NG

5.REPLACE REMOTE ENGINE STARTER ECU
5.REPLACE REMOTE ENGINE STARTER ECU
a.

Temporarily replace the remote engine starter ECU with a new one.


b.

Register the remote engine starter ID.

HINT:

Refer to Service Bulletin.



c.

Check the remote engine starter function.

OK:

Remote engine starter functions operate normally.



Result:
Proceed to
OK
NG



OK

END (REMOTE ENGINE STARTER ECU WAS DEFECTIVE)

NG

6.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
6.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Temporarily replace the main body ECU (multiplex network body ECU) with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

HINT:

Refer to Service Bulletin.



b.

Check the remote engine starter function.

OK:

Remote engine starter functions operate normally.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)