If there is a communication malfunction between the hybrid vehicle control ECU and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the hybrid vehicle control ECU stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B279986 | Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid | Either of the following conditions is met (1 trip detection logic*):
·
A malfunction is detected in the communication or communication lines between the hybrid vehicle control ECU and ID code box (immobiliser code ECU). ·
The communication ID codes of the hybrid vehicle control ECU and ID code box (immobiliser code ECU) do not match. |
·
ID code box (immobiliser code ECU) ·
hybrid vehicle control ECU ·
Wire harness or connector |
DTC output confirmation operation (Perform either of the following):
·
Start the hybrid system and wait for 10 seconds. If there is a malfunction, the hybrid control system will stop (communication begins within 3 seconds of the hybrid control system start, and DTCs are stored after 6 seconds). ·
Connect the cable to the negative (-) auxiliary battery terminal, start the hybrid system and wait for 10 seconds (communication begins within 3 seconds of the power switch being turned on (IG), and DTCs are stored after 6 seconds). |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Hybrid control system cannot be started | - |
| DTC No. | Data List and Active Test |
|---|---|
| B279986 | - |
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
When replacing the hybrid vehicle control ECU or ID code box (immobiliser code ECU), refer to Service Bulletin.
After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."
When DTC B279986 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.
Register the communication ID codes.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
*b | Waveform |
| *c | Approximately 160 ms. | *d | Approximately 270 ms. |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F3-23 (IMO) - Body ground | Turn the power switch on (READY) | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform) |
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Terminal IMO stuck low (2.4 V or less) | B |
| Waveform not output, or has abnormal wavelength or shape | C |
A
B
C
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
*b | Waveform |
| *c | Approximately 160 ms. | *d | Approximately 270 ms. |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F3-10 (IMI) - Body ground | Power switch turned on (IG) using registered electrical key transmitter sub-assembly | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Register the ECU communication ID codes.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the power switch on (IG).
Check that the hybrid control system starts 5 seconds after the power switch turned on (IG).
Hybrid control system starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F3 hybrid vehicle control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F3-23 (IMO) - Body ground | Power switch turned on (IG) using registered electrical key transmitter sub-assembly | Terminal IMO stuck low (2.4 V or less) |
| Terminal IMO stuck high (12 V) or abnormal waveform |
| Result | Proceed to |
|---|---|
| Terminal IMO stuck low (2.4 V or less) | A |
| Terminal IMO stuck high (12 V) or abnormal waveform | B |
A
B
Disconnect the F19 ID code box (immobiliser code ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F19-3 (EFII) - F3-23 (IMO) | Always | Below 1 Ω |
| F19-3 (EFII) or F3-23 (IMO) - Body ground | Always | 10 kΩ or higher |
| F19-4 (EFIO) - F3-10 (IMI) | Always | Below 1 Ω |
| F19-4 (EFIO) or F3-10 (IMI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the hybrid vehicle control ECU with a new one.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
DTC B279986 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG