Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM
RM3210E _58 Vehicle Interior _047507 THEFT DETERRENT / KEYLESS ENTRY _0244661 IMMOBILISER SYSTEM Y

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use this procedure to troubleshoot the immobiliser system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:


What Vehicle model, system name
When Date, time, occurrence frequency
Where Whether the problem occurs at a specific location.
Under what conditions? Whether the doors were locked or unlocked, whether the power switch was on, whether the hybrid control system was starting.
How did it happen? Problem symptoms


Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY VOLTAGE
3.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

HINT:

A simple method to determine whether the auxiliary battery is discharged is to operate the horn.



Result:
Proceed to
NEXT



NEXT

4.TURN POWER SWITCH ON (IG)
4.TURN POWER SWITCH ON (IG)
NOTICE:

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.


Result:
Proceed to
NEXT



NEXT

5.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
5.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check for CAN communication system DTCs.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

6.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

B

6.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Using the GTS, check for LIN communication system DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
LIN DTCs are not output A
LIN DTCs are output B



A

7.CHECK FOR DTC*

B

7.CHECK FOR DTC*
a.

Check for DTCs and make a note of any codes that are output.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > Hybrid Control > Trouble Codes
50001 236

b.

Based on the DTCs output above, proceed to each diagnostic procedure.


Result:
Result Proceed to
DTCs are not output A
Hybrid control system DTCs are output B
Electronic shift lever system DTCs are output C
Immobiliser system DTCs are output D



A

8.PROBLEM SYMPTOMS TABLE

B

C

D

8.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

9.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

10.REPAIR OR REPLACE
9.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

10.REPAIR OR REPLACE
10.REPAIR OR REPLACE
HINT:

When replacing the Certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU), main body ECU (multiplex network body ECU), hybrid vehicle control ECU or electrical key transmitter sub-assembly refer to Service Bulletin.


Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC*
11.CHECK FOR DTC*
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125
Powertrain > Hybrid Control > Clear DTCs
50002 236

b.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > Hybrid Control > Trouble Codes
50001 236
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.



Result:
Result Proceed to
DTCs are not output A
Immobiliser system DTCs are output B



A

END

B