Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM
RM3210E _58 Vehicle Interior _047507 THEFT DETERRENT / KEYLESS ENTRY _0244661 IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  Security Indicator Light Does not Blink  


DESCRIPTION

·

The certification ECU (smart key ECU assembly) blinks the security indicator light (combination meter assembly) when the immobiliser is set (power switch off).

·

The certification ECU (smart key ECU assembly) receives the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is in the arming preparation state or alarm sounding state. Then, the certification ECU (smart key ECU assembly) blinks the security indicator light (combination meter assembly).


WIRING DIAGRAM

B438385E02
0.458,2.458 4.125,2.656 3.667,0.198 10 false : CAN Communication Line 0.219,1.396 0.771,1.656 0.552,0.26 10 false F7 0.219,1.563 2.469,2.01 2.25,0.448 10 false Security Indicator Light (Combination Meter Assembly) 2.958,1.417 3.51,1.677 0.552,0.26 10 false F1 2.958,1.573 4.458,2.021 1.5,0.448 10 false Certification ECU (Smart Key ECU Assembly) 5.375,1.438 7.021,1.885 1.646,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 3.313,0.333 3.865,0.594 0.552,0.26 10 false 12 V 3.083,0.594 3.635,0.854 0.552,0.26 10 false IND 2.844,0.646 3.396,0.906 0.552,0.26 10 false 20 1.292,0.75 1.844,1.01 0.552,0.26 10 false LP 1.573,0.635 2.125,0.896 0.552,0.26 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > Hybrid Control > Trouble Codes
50001 236
OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)

NG

2.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF/ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Immobiliser Indicator
50004 125 28
OK:

The security indicator light (combination meter assembly) operates normally.



Result:
Proceed to
OK
NG



OK

3.CHECK SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) OPERATION

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY))
3.CHECK SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) OPERATION
a.

When the immobiliser is set, check that the security indicator light (combination meter assembly) blinks.*1

OK:

The security indicator light (combination meter assembly) blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light (combination meter assembly) illuminates.*2

OK:

The security indicator light (combination meter assembly) illuminates normally.



Result:
Result Proceed to
*1 is NG (*2 is OK) A
*2 is NG (*1 is OK) B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY))
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F7 security indicator light (combination meter assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-20 (IND) - F7-2 (LP) Always Below 1 Ω
F1-20 (IND) or F7-2 (LP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the F7 security indicator light (combination meter assembly) connector.


c.

Using an oscilloscope, check the waveform.

B427583C20
4.531,0.417 4.948,0.667 0.417,0.25 5.354,2.313 5.021,2.313 5.021,2.313 5.021,1.354 false 0.396,0.177 0.708,0.333 0.313,0.156 10 false *a 4.646,0.458 5.146,0.667 0.5,0.208 10 false F1 5.406,2.25 5.906,2.458 0.5,0.208 10 false IND
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Measurement Condition:
Tester Connection Condition Specified Condition
F1-20 (IND) - Body ground Power switch off → on (IG) Pulse generation → Below 2 V



Result:
Proceed to
OK
NG



OK

REPLACE SECURITY INDICATOR LIGHT (METER CIRCUIT PLATE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)