Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM3210E _59 Vehicle Exterior _047515 WINDOW / GLASS _0241844 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  REMOVAL  


PROCEDURE

Hide 85110R 2.REMOVE REAR WIPER MOTOR ASSEMBLY

Hide 85345R 3.REMOVE REAR WASHER NOZZLE

HINT:

When reusing the back door glass.

Click hereVehicle Exterior>WIPER / WASHER>WASHER NOZZLE(for Rear Side)>REMOVAL


Hide 68131 4.REMOVE BACK DOOR GLASS SUB-ASSEMBLY

a.

Disconnect each connector and disengage each clamp.


b.

When replacing the back door glass sub-assembly with a new one:

i.
B435168

Disconnect the rear washer hose and disengage the clamp.



c.
B433407C02
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area around the installation position of the back door glass sub-assembly on the back door panel to prevent it from being scratched.


d.
B433408C02
1.406,0.75 1.406,0.083 1.406,0.083 1.656,0.083 true 1.406,0.417 1.656,0.417 false 1.333,0.771 1.646,0.927 0.313,0.156 10 false *a
*a Matchmark


Place matchmarks on the back door glass sub-assembly and back door panel at the locations indicated in the illustration.

HINT:

Matchmarks are not necessary if the back door glass is not going to be reused.



e.
B433410C02
2.76,1.115 3.115,1.479 false 1,0.385 0.385,0.49 false 2.417,0.375 3,0.458 false 3.063,0.375 3.375,0.531 0.313,0.156 10 false *1 0.198,0.417 0.51,0.573 0.313,0.156 10 false *2 3.073,1.5 3.302,1.74 0.229,0.24 10 false *a
*1 No. 1 Back Window Glass Spacer
*2 No. 2 Back Window Glass Spacer
*a Piano Wire


Pass a piano wire between the back door panel and back door glass sub-assembly from the interior.


f.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


g.

Cut the adhesive by pulling the piano wire around the back door glass sub-assembly.

NOTICE:
·

When separating the back door glass sub-assembly, take care not to damage the paint or interior and exterior ornaments.

·

When cutting the adhesive, take care not to damage the connectors on the back door glass sub-assembly.

·

Do not pull the piano wire in a vertical direction, but pull it in a horizontal direction.




h.
B433411

Using suction cups, disengage the No. 1 back window glass spacer and No. 2 back window glass spacer and remove the back door glass sub-assembly.

NOTICE:
·

To prevent the back door glass sub-assembly from falling when performing this operation, be sure to hold the back door glass sub-assembly using suction cups.

·

Be careful not to drop the back door glass sub-assembly.

·

Leave as much adhesive on the back door panel as possible when removing the back door glass sub-assembly.




Hide 75571F 5.REMOVE BACK DOOR WINDOW MOULDING

a.

When reusing the back door glass:

i.
B433412C02
0.094,0.063 0.417,0.417 0.323,0.354 12 false *A
*A Back Side


Using a scraper, remove the back door window moulding.

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back door window moulding with a new one.





Hide 64818C 6.REMOVE NO. 1 BACK WINDOW GLASS SPACER

a.

When reusing the back door glass:

i.
B433413C02
0.115,0.094 0.396,0.427 0.281,0.333 12 false *A
*A Back Side


Using a scraper, remove the No. 1 back window glass spacer.

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the No. 1 back window glass spacer with a new one.





Hide 64819B 7.REMOVE NO. 2 BACK WINDOW GLASS SPACER

HINT:

Use the same procedure as for the No. 1 back window glass spacer.


Hide 68294A 8.REMOVE BACK DOOR GLASS ADHESIVE DAM

a.

When reusing the back door glass:

i.
B433414C02
0.104,0.104 0.396,0.385 0.292,0.281 12 false *A
*A Back Side


Using a scraper, remove the back door glass adhesive dam.

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back door glass adhesive dam with a new one.





Hide 62785F 9.REMOVE BACK DOOR GLASS SPACER

a.

When reusing the back door glass:

i.
B435175C01
0.104,0.094 0.427,0.396 0.323,0.302 12 false *A
*A Back Side


Using a scraper, remove the back door glass spacer.

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back door glass spacer with a new one.





Hide 10.CLEAN BACK DOOR GLASS

a.

When reusing the back door glass:

i.
B187131

Using a scraper, remove any remaining adhesive residue from the back door glass.

NOTICE:

Be careful not to damage the back door glass.



ii.

Clean the outer circumference of the back door glass with a non-residue solvent.

NOTICE:
·

Do not touch the back door glass surface after cleaning it.

·

Even if using a new back door glass, clean it with a non-residue solvent.





Hide 76801 11.REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 64821 12.REMOVE BACK WINDOW FIX GLASS SUB-ASSEMBLY

a.

Disconnect each connector.


b.
B433415C02
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area around the installation position of the back window fix glass sub-assembly on the back door panel to prevent it from being scratched.


c.
B435153C02
1.406,1.813 1.406,1.229 1.406,1.229 1.656,1.229 true 1.417,1.542 1.667,1.542 true 1.333,1.854 1.646,2.01 0.313,0.156 10 false *a
*a Matchmark


Place matchmarks on the back window fix glass sub-assembly and back door panel at the locations indicated in the illustration.

HINT:

Matchmarks are not necessary if the back window fix glass is not going to be reused.



d.
B433417C02
0.594,1.292 0.76,1.698 false 1.646,1.531 1.813,1.76 false 2.833,1.292 2.635,1.708 false 2.552,1.76 2.865,1.917 0.313,0.156 10 false *1 0.677,1.75 0.99,1.906 0.313,0.156 10 false *2 1.75,1.802 2.063,1.958 0.313,0.156 10 false *a
*1 No. 3 Back Window Glass Spacer
*2 No. 4 Back Window Glass Spacer
*a Piano Wire


Pass a piano wire between the back door panel and back window fix glass sub-assembly from the interior.


e.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


f.

Cut the adhesive by pulling the piano wire around the back window fix glass sub-assembly.

NOTICE:
·

When separating the back window fix glass sub-assembly, take care not to damage the paint or interior and exterior ornaments.

·

When cutting the adhesive, take care not to damage the connectors on the back window fix glass sub-assembly.

·

Do not pull the piano wire in a vertical direction, but pull it in a horizontal direction.




g.
B433418

Using suction cups, disengage the No. 3 back window glass spacer and No. 4 back window glass spacer and remove the back window fix glass sub-assembly.

NOTICE:
·

To prevent the back window fix glass sub-assembly from falling when performing this operation, be sure to hold the back window fix glass sub-assembly using suction cups.

·

Be careful not to drop the back window fix glass sub-assembly.

·

Leave as much adhesive on the back door panel as possible when removing the back window fix glass sub-assembly.




Hide 68294D 13.REMOVE NO. 2 BACK DOOR GLASS ADHESIVE DAM

a.

When reusing the back window fix glass:

i.
B433419C02
0.083,0.073 0.385,0.385 0.302,0.313 12 false *A
*A Back Side


Using a scraper, remove the No. 2 back door glass adhesive dam.

NOTICE:
·

Be careful not to damage the back window fix glass.

·

Be sure to replace the No. 2 back door glass adhesive dam with a new one.





Hide 75573J 14.REMOVE NO. 2 BACK WINDOW OUTSIDE MOULDING RH

a.

When reusing the back window fix glass:

i.
B433420C02
0.083,0.094 0.406,0.385 0.323,0.292 12 false *A
*A Back Side


Using a scraper, remove the No. 2 back window outside moulding RH.

NOTICE:
·

Be careful not to damage the back window fix glass.

·

Be sure to replace the No. 2 back window outside moulding RH with a new one.





Hide 75574D 15.REMOVE NO. 2 BACK WINDOW OUTSIDE MOULDING LH

HINT:

Use the same procedure as for the RH side.


Hide 75575H 16.REMOVE LOWER NO. 2 BACK WINDOW MOULDING

a.

When reusing the back window fix glass:

i.
B433421C01
0.115,0.104 0.406,0.385 0.292,0.281 12 false *A
*A Back Side


Using a scraper, remove the lower No. 2 back window moulding.

NOTICE:
·

Be careful not to damage the back window fix glass.

·

Be sure to replace the lower No. 2 back window moulding with a new one.





Hide 64818D 17.REMOVE NO. 3 BACK WINDOW GLASS SPACER

a.

When reusing the back window fix glass:

i.
B433422C02
0.104,0.094 0.427,0.344 0.323,0.25 12 false *A
*A Back Side


Using a scraper, remove the No. 3 back window glass spacer.

NOTICE:
·

Be careful not to damage the back window fix glass.

·

Be sure to replace the No. 3 back window glass spacer with a new one.





Hide 64819D 18.REMOVE NO. 4 BACK WINDOW GLASS SPACER

HINT:

Use the same procedure as for the No. 3 back window glass spacer.


Hide 19.CLEAN BACK WINDOW FIX GLASS

a.

When reusing the back window fix glass:

i.
B187131

Using a scraper, remove any remaining adhesive residue from the back window fix glass.

NOTICE:

Be careful not to damage the back window fix glass.



ii.

Clean the outer circumference of the back window fix glass with a non-residue solvent.

NOTICE:
·

Do not touch the back window fix glass surface after cleaning it.

·

Even if using a new back window fix glass, clean it with a non-residue solvent.





Hide 20.CLEAN BACK DOOR PANEL

a.

Clean and shape the contact surfaces of the back door panel.

i.
B433433C02
0.781,0.604 1.073,0.948 false 0.604,0.531 0.917,0.688 0.313,0.156 10 false *a 1.885,1 2.042,1.198 0.156,0.198 10 false a
*a Back Door Panel
V100155

Adhesive


Using a knife, cut off any excess adhesive on the contact surfaces of the back door panel as shown in the illustration.

Standard Dimension:
Area Dimension
a 1.0 mm (0.0394 in.) or more


NOTICE:

Be careful not to damage the back door panel.


HINT:

Leave as much adhesive on the back door panel as possible.



ii.

Clean the contact surfaces of the back door panel with a piece of cloth saturated with non-residue solvent.

HINT:

Even if all of the adhesive has been removed, clean the back door panel.