Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM3210E _59 Vehicle Exterior _047515 WINDOW / GLASS _0241844 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


PROCEDURE

Hide 64818D 1.INSTALL NO. 3 BACK WINDOW GLASS SPACER

a.

Using a brush or sponge, coat the installation area of a new No. 3 back window glass spacer with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B433423C02
1.771,3.01 2.135,2.813 2.135,2.813 2.094,3.01 false 1.771,3.49 1.865,3.656 1.865,3.656 2.094,3.531 false 0.125,0.073 0.438,0.375 0.313,0.302 12 false *A 2.198,2.729 2.51,2.885 0.313,0.156 10 false *a 1.792,3.656 2.104,3.813 0.313,0.156 10 false *a
*A Back Side
*a Ceramic Notch


Install the new No. 3 back window glass spacer to the back window fix glass as shown in the illustration.


Hide 64819D 2.INSTALL NO. 4 BACK WINDOW GLASS SPACER

HINT:

Use the same procedure as for the No. 3 back window glass spacer.


Hide 75575H 3.INSTALL LOWER NO. 2 BACK WINDOW MOULDING

a.

Using a brush or sponge, coat the installation area of a new lower No. 2 back window moulding with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B433424C02
1.198,1.729 0.969,2 false 0.135,0.073 0.448,0.333 0.313,0.26 12 false *A 2.156,3.563 2.313,3.76 0.156,0.198 10 false a 0.885,2.021 1.198,2.219 0.313,0.198 10 false *a
*A Back Side
*a Back Window Fix Glass Edge Side


Install the new lower No. 2 back window moulding to the back window fix glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 6.7 mm (0.264 in.)



Hide 75573J 4.INSTALL NO. 2 BACK WINDOW OUTSIDE MOULDING RH

a.

Using a brush or sponge, coat the installation area of a new No. 2 back window outside moulding RH with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B433425C02
1.323,0.729 1.521,0.938 false 1.354,2.396 1.854,2.323 false 0.104,0.094 0.479,0.417 0.375,0.323 12 false *A 1.438,2.146 1.594,2.344 0.156,0.198 10 false A 1.417,2.698 1.573,2.896 0.156,0.198 10 false A 0.906,3.188 1.354,3.448 0.448,0.26 10 false A-A 1.188,3.813 1.385,4.042 0.198,0.229 10 false a 1.583,0.854 1.896,1.01 0.313,0.156 10 false *a 1.906,2.24 2.219,2.396 0.313,0.156 10 false *a
*A Back Side
*a Ceramic Notch


Install the new No. 2 back window outside moulding RH to the back window fix glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 2.1 mm (0.0827 in.)



Hide 75574D 5.INSTALL NO. 2 BACK WINDOW OUTSIDE MOULDING LH

HINT:

Use the same procedure as for the RH side.


Hide 68294D 6.INSTALL NO. 2 BACK DOOR GLASS ADHESIVE DAM

a.
B274197C02
3.094,0.802 2.427,0.427 false 1.531,1.729 1.688,1.927 0.156,0.198 10 false a 2.26,0.344 2.573,0.542 0.313,0.198 10 false *a
*a Cut


Cut a new No. 2 back door glass adhesive dam so that it is the appropriate size as shown in the illustration.

Standard Dimension:
Area Dimension
a 79.9 to 80.9 cm (2.62 to 2.65 ft.)



b.

Using a brush or sponge, coat the installation area of the new No. 2 back door glass adhesive dam with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



c.
B433426C02
0.927,1.385 1.021,1.573 false 2.479,1.396 2.396,1.583 false 0.073,0.073 0.438,0.396 0.365,0.323 12 false *A 0.969,1.594 1.281,1.75 0.313,0.156 10 false *a 2.333,1.583 2.646,1.74 0.313,0.156 10 false *a
*A Back Side
*a Ceramic Notch


Install the No. 2 back door glass adhesive dam to the back window fix glass as shown in the illustration.


Hide 64821 7.INSTALL BACK WINDOW FIX GLASS SUB-ASSEMBLY

a.
B435153C02
1.406,1.813 1.406,1.229 1.406,1.229 1.656,1.229 true 1.417,1.542 1.667,1.542 true 1.333,1.854 1.646,2.01 0.313,0.156 10 false *a
*a Matchmark


Position the back window fix glass sub-assembly.

i.

Using suction cups, place the back window fix glass sub-assembly in the correct position.


ii.

Check that the whole contact surface of the back window fix glass sub-assembly rim is perfectly even.


iii.

Align the matchmarks on the back window fix glass sub-assembly and back door panel.

NOTICE:

Check that the No. 3 and No. 4 back window glass spacers are engaged to the back door panel correctly.



iv.

Remove the back window fix glass sub-assembly.



b.

Using a brush, coat the installation surfaces on the back door panel with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



c.

Using a brush or sponge, coat the adhesive application area with primer G.

B433428C02
5.844,1.167 6.323,1.292 false 5.854,1.458 6.083,1.75 false 5.802,1.5 6.083,1.75 6.083,1.75 5.896,1.396 false 1.292,1.458 1.167,1.708 1.167,1.708 1.344,1.5 false 3.49,2.938 3.573,3.313 3.573,3.313 3.708,2.938 false 0.115,0.094 0.417,0.406 0.302,0.313 12 false *A 6.406,1.208 6.719,1.365 0.313,0.156 10 false *a 3.146,0.625 3.313,0.823 0.167,0.198 10 false A 3.156,0.958 3.323,1.156 0.167,0.198 10 true A 3.146,1.333 3.313,1.531 0.167,0.198 10 true C 3.188,1.698 3.354,1.896 0.167,0.198 10 false C 1.208,0.708 1.375,0.906 0.167,0.198 10 false B 1.521,0.708 1.677,0.885 0.156,0.177 10 true B 0.49,2.24 1.021,2.417 0.531,0.177 10 false A-A 2.865,2.219 3.396,2.396 0.531,0.177 10 false B-B 5.271,2.25 5.802,2.427 0.531,0.177 10 false C-C 1.406,2.438 1.563,2.635 0.156,0.198 10 false a 3.365,2.708 3.521,2.906 0.156,0.198 10 false b 3.573,2.365 3.729,2.563 0.156,0.198 10 false c 3.792,2.646 3.948,2.844 0.156,0.198 10 false d 5.885,2.417 6.042,2.615 0.156,0.198 10 false e 1.104,1.74 1.417,1.938 0.313,0.198 10 false *b 6.031,1.771 6.344,1.969 0.313,0.198 10 false *b 3.51,3.354 3.823,3.552 0.313,0.198 10 false *a
*A Back Side - -
*a Adhesive Positioning Center *b Ceramic Notch
V100155

Primer G - -


Standard Dimension:
Area Dimension
a 11.0 mm (0.433 in.) or more
b 7.0 mm (0.276 in.) or more
c 8.0 mm (0.315 in.)
d 7.0 mm (0.276 in.) or more
e 11.0 mm (0.433 in.) or more


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:
·

Apply primer G to the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.




d.

Apply adhesive to the back window fix glass sub-assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 to 15.0 mm (0.472 to 0.591 in.)
b 8.0 to 11.0 mm (0.315 to 0.433 in.)



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back window fix glass sub-assembly as shown in the illustration.

B433429C02
5.844,1.177 6.417,1.229 false 5.854,1.448 6.083,1.75 false 5.792,1.49 6.083,1.75 6.083,1.75 5.885,1.396 false 1.302,1.448 1.25,1.771 1.25,1.771 1.354,1.51 false 3.479,2.927 3.573,3.271 3.573,3.271 3.708,2.917 false 1.375,2.927 1.094,3.271 false 5.854,2.948 5.573,3.292 false 0.104,0.083 0.438,0.375 0.333,0.292 12 false *A 6.51,1.167 6.823,1.323 0.313,0.156 10 false *a 1.167,1.833 1.479,1.99 0.313,0.156 10 false *b 6.052,1.813 6.365,1.969 0.313,0.156 10 false *b 3.198,1.708 3.354,1.906 0.156,0.198 10 false C 3.188,0.948 3.333,1.167 0.146,0.219 10 true A 1.51,0.75 1.656,0.896 0.146,0.146 10 true B 3.188,1.354 3.333,1.5 0.146,0.146 10 true C 3.208,0.625 3.365,0.823 0.156,0.198 10 false A 1.198,0.74 1.354,0.938 0.156,0.198 10 false B 0.521,2.292 0.99,2.5 0.469,0.208 10 false A-A 2.76,2.292 3.229,2.5 0.469,0.208 10 false B-B 5.052,2.302 5.521,2.51 0.469,0.208 10 false C-C 1.469,2.302 1.625,2.5 0.156,0.198 10 false a 3.583,2.323 3.74,2.521 0.156,0.198 10 false b 5.688,2.323 5.844,2.521 0.156,0.198 10 false c 1.031,3.292 1.344,3.448 0.313,0.156 10 false *a 3.51,3.302 3.823,3.458 0.313,0.156 10 false *a 5.5,3.323 5.813,3.479 0.313,0.156 10 false *a
*A Back Side - -
*a Adhesive Positioning Center *b Ceramic Notch
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 8.3 mm (0.327 in.)
b 8.0 mm (0.315 in.)
c 10.8 mm (0.425 in.)


HINT:

Apply adhesive to the ceramic notches.




e.

Install the back window fix glass sub-assembly.

i.
B435153C02
1.406,1.813 1.406,1.229 1.406,1.229 1.656,1.229 true 1.417,1.542 1.667,1.542 true 1.333,1.854 1.646,2.01 0.313,0.156 10 false *a
*a Matchmark


Using suction cups, position the back window fix glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the No. 3 and No. 4 back window glass spacers are engaged to the back door panel correctly.

·

Check the clearance between the back door panel and back window fix glass sub-assembly.




ii.

Lightly press the outer surface of the back window fix glass sub-assembly to ensure a close fit.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the back window fix glass sub-assembly using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




f.

Connect each connector.


Hide 76801 8.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 62785F 9.INSTALL BACK DOOR GLASS SPACER

a.

Using a brush or sponge, coat the installation area of the new back door glass spacer with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B435172C01
2.229,1.365 2.448,1.01 false 1.198,1.354 1.031,1.021 false 0.115,0.115 0.448,0.427 0.333,0.313 12 false *A 0.844,0.917 1.156,1.073 0.313,0.156 10 false *a 2.51,0.906 2.823,1.063 0.313,0.156 10 false *a
*A Back Side
*a Ceramic Notch


Install the back door glass spacer to the back door glass as shown in the illustration.


Hide 68294A 10.INSTALL BACK DOOR GLASS ADHESIVE DAM

a.
B274197C02
3.094,0.802 2.427,0.427 false 1.531,1.729 1.688,1.927 0.156,0.198 10 false a 2.26,0.344 2.573,0.542 0.313,0.198 10 false *a
*a Cut


Cut a new back door glass adhesive dam so that it is the appropriate size as shown in the illustration.

Standard Dimension:
Area Dimension
a 95.0 to 96.0 cm (3.12 to 3.15 ft.)



b.

Using a brush or sponge, coat the installation area of the new back door glass adhesive dam with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



c.
B433430C02
0.844,0.781 0.917,1.052 false 2.615,0.781 2.49,1.063 false 0.073,0.094 0.375,0.448 0.302,0.354 12 false *A 0.677,0.667 0.99,0.823 0.313,0.156 10 false *a 2.656,0.698 2.969,0.854 0.313,0.156 10 false *a
*A Back Side
*a Ceramic Notch


Install the back door glass adhesive dam to the back door glass as shown in the illustration.


Hide 64818C 11.INSTALL NO. 1 BACK WINDOW GLASS SPACER

a.

Using a brush or sponge, coat the installation area of a new No. 1 back window glass spacer with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B433431C02
1.417,3.958 1.979,3.76 false 1.021,0.229 1.427,0.313 false 0.531,0.979 0.396,0.74 false 0.104,0.073 0.385,0.438 0.281,0.365 12 false *A 1.208,3.875 1.521,4.031 0.313,0.156 10 false *a 1.813,0.375 1.969,0.573 0.156,0.198 10 true a 0.646,1.354 0.802,1.552 0.156,0.198 10 true b 0.833,0.135 1.146,0.292 0.313,0.156 10 false *b 0.229,0.646 0.542,0.802 0.313,0.156 10 false *b
*A Back Side
*a Ceramic Notch
*b Edge Of Curved Surface


Install the new No. 1 back window glass spacer to the back door glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 71.0 mm (2.80 in.)
b 98.8 mm (3.89 in.)



Hide 64819B 12.INSTALL NO. 2 BACK WINDOW GLASS SPACER

HINT:

Use the same procedure as for the No. 1 back window glass spacer.


Hide 75571F 13.INSTALL BACK DOOR WINDOW MOULDING

a.

Using a brush or sponge, coat the installation area of a new back door window moulding with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B433432C02
0.167,1.188 0.323,1.385 0.156,0.198 10 false A 0.594,1.208 0.771,1.365 0.177,0.156 10 true A 1.281,2.042 1.427,2.25 0.146,0.208 10 true B 1.292,2.479 1.448,2.677 0.156,0.198 10 false B 0.24,3.094 0.719,3.302 0.479,0.208 10 false A-A 1.615,3.115 2.094,3.323 0.479,0.208 10 false B-B 0.708,4.052 0.865,4.25 0.156,0.198 10 false a 2.302,4.052 2.458,4.25 0.156,0.198 10 false b 0.094,0.073 0.438,0.385 0.344,0.313 12 false *A
*A Back Side


Install the new back door window moulding to the back door glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 7.9 mm (0.311 in.)
b 7.0 mm (0.276 in.)



Hide 68131 14.INSTALL BACK DOOR GLASS SUB-ASSEMBLY

a.
B433408C02
1.406,0.75 1.406,0.083 1.406,0.083 1.656,0.083 true 1.406,0.417 1.656,0.417 false 1.333,0.771 1.646,0.927 0.313,0.156 10 false *a
*a Matchmark


Position the back door glass sub-assembly.

i.

Using suction cups, place the back door glass sub-assembly in the correct position.


ii.

Check that the whole contact surface of the back door glass sub-assembly rim is perfectly even.


iii.

Align the matchmarks on the back door glass sub-assembly and back door panel.

NOTICE:

Check that the No. 1 and No. 2 back window glass spacers are engaged to the back door panel correctly.



iv.

Remove the back door glass sub-assembly.



b.

Using a brush, coat the installation surfaces on the back door panel with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



c.

Using a brush or sponge, coat the adhesive application area with primer G.

B433434C02
3.948,1.729 4.385,2.083 false 3.979,2.115 4.25,2.5 4.25,2.5 3.958,2.229 false 3.885,2.292 4.25,2.5 4.25,2.5 3.792,2.354 false 1.323,0.75 0.75,0.583 0.75,0.583 1.208,0.792 false 1.094,0.854 0.75,0.583 0.75,0.583 1.021,0.948 false 0.75,0.583 1.031,0.885 false 5.885,1.083 6.177,1.375 false 5.542,2.438 5.958,2.75 5.958,2.75 5.74,2.438 false 5.448,3.979 5.74,4.271 false 2.323,3.979 2.615,4.271 false 0.104,0.104 0.458,0.417 0.354,0.313 12 false *A 4.365,2.115 4.677,2.271 0.313,0.156 10 false *a 4.302,2.458 4.615,2.615 0.313,0.156 10 false *b 0.552,0.51 0.865,0.667 0.313,0.156 10 false *b 2.063,0.427 2.219,0.625 0.156,0.198 10 false A 2.063,0.792 2.219,0.99 0.156,0.198 10 false A 1.063,1.125 1.219,1.323 0.156,0.198 10 false B 0.729,1.104 0.885,1.302 0.156,0.198 10 false B 1.094,1.844 1.25,2.042 0.156,0.198 10 true C 0.563,2.167 0.719,2.365 0.156,0.198 10 false C 2.052,2.354 2.198,2.521 0.146,0.167 10 true D 2.063,2.719 2.219,2.917 0.156,0.198 10 false D 2.198,3.458 2.354,3.656 0.156,0.198 10 false a 2.542,3.458 2.698,3.656 0.156,0.198 10 false b 5.448,0.656 5.604,0.854 0.156,0.198 10 false c 5.958,0.438 6.115,0.635 0.156,0.198 10 false d 5.292,1.24 5.448,1.438 0.156,0.198 10 false e 5.479,1.792 5.635,1.99 0.156,0.198 10 false f 5.813,1.906 5.969,2.104 0.156,0.198 10 false g 5.313,2.573 5.469,2.771 0.156,0.198 10 false h 5.438,2.802 5.594,3 0.156,0.198 10 false i 5.031,3.563 5.188,3.76 0.156,0.198 10 false j 5.5,3.333 5.656,3.531 0.156,0.198 10 false k 5.271,4.115 5.427,4.313 0.156,0.198 10 false l 6.125,1.396 6.438,1.552 0.313,0.156 10 false *a 5.906,2.792 6.219,2.948 0.313,0.156 10 false *a 5.677,4.292 5.99,4.448 0.313,0.156 10 false *a 2.552,4.292 2.865,4.448 0.313,0.156 10 false *a 1.479,3.281 1.927,3.5 0.448,0.219 10 false A-A 4.688,0.198 5.135,0.417 0.448,0.219 10 false B-B 4.75,1.771 5.198,1.99 0.448,0.219 10 false C-C 4.76,3.24 5.208,3.458 0.448,0.219 10 false D-D
*A Back Side - -
*a Adhesive Positioning Center *b Ceramic Notch
V100155

Primer G - -


Standard Dimension:
Area Dimension
a 7.0 mm (0.276 in.) or more
b 16.9 mm (0.665 in.)
c 7.0 mm (0.276 in.) or more
d 7.0 mm (0.276 in.) or more
e 43.7 mm (1.72 in.)
f 7.0 mm (0.276 in.) or more
g 7.0 mm (0.276 in.) or more
h 16.9 mm (0.665 in.)
i 25.0 mm (0.984 in.)
j 4.0 mm (0.157 in.) or more
k 7.0 mm (0.276 in.) or more
l 12.1 mm (0.476 in.)


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:
·

Apply primer G to the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.




d.

Apply adhesive to the back door glass sub-assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 to 15.0 mm (0.472 to 0.591 in.)
b 8.0 to 11.0 mm (0.315 to 0.433 in.)



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back door glass sub-assembly as shown in the illustration.

B435069C02
3.938,1.583 4.313,1.958 false 5.885,1.083 6.104,1.375 false 5.448,3.979 5.667,4.271 false 2.323,3.969 2.542,4.26 false 5.542,2.427 5.948,2.698 5.948,2.698 5.76,2.417 false 3.792,2.365 4.167,2.5 4.167,2.5 3.885,2.302 false 3.958,2.229 4.167,2.5 4.167,2.5 3.969,2.104 false 1.229,0.802 0.75,0.5 0.75,0.5 1.313,0.74 false 1.01,0.948 0.75,0.5 0.75,0.5 1.094,0.865 false 0.75,0.5 1.042,0.896 false 0.125,0.094 0.479,0.375 0.354,0.281 12 false *A 4.375,1.896 4.688,2.052 0.313,0.156 10 false *a 0.573,0.417 0.885,0.573 0.313,0.156 10 false *b 4.219,2.448 4.531,2.604 0.313,0.156 10 false *b 2.073,0.417 2.229,0.615 0.156,0.198 10 false A 0.729,1.104 0.885,1.302 0.156,0.198 10 false B 1.063,1.115 1.219,1.313 0.156,0.198 10 false B 1.094,1.875 1.25,2.073 0.156,0.198 10 true C 0.563,2.177 0.719,2.375 0.156,0.198 10 false C 2.063,2.323 2.188,2.51 0.125,0.188 10 true D 2.063,2.719 2.219,2.917 0.156,0.198 10 false D 2.073,0.76 2.229,0.958 0.156,0.198 10 false A 1.552,3.365 1.938,3.625 0.385,0.26 10 false A-A 4.563,0.417 4.948,0.677 0.385,0.26 10 false B-B 4.875,1.865 5.26,2.125 0.385,0.26 10 false C-C 4.802,3.292 5.188,3.552 0.385,0.26 10 false D-D 6.073,1.406 6.396,1.604 0.323,0.198 10 false *a 5.906,2.719 6.219,2.875 0.313,0.156 10 false *a 5.615,4.281 5.927,4.438 0.313,0.156 10 false *a 2.5,4.292 2.813,4.448 0.313,0.156 10 false *a 2.531,3.365 2.688,3.563 0.156,0.198 10 false a 5.302,1.208 5.458,1.406 0.156,0.198 10 false b 5.313,2.563 5.469,2.76 0.156,0.198 10 false c 5.417,2.792 5.573,2.99 0.156,0.198 10 false d 5.25,4.104 5.406,4.302 0.156,0.198 10 false e
*A Back Side - -
*a Adhesive Positioning Center *b Ceramic Notch
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 16.9 mm (0.665 in.)
b 43.7 mm (1.72 in.)
c 16.9 mm (0.665 in.)
d 25.0 mm (0.984 in.)
e 12.1 mm (0.476 in.)


HINT:

Apply adhesive to the ceramic notches.




e.

Install the back door glass sub-assembly.

i.
B433408C02
1.406,0.75 1.406,0.083 1.406,0.083 1.656,0.083 true 1.406,0.417 1.656,0.417 false 1.333,0.771 1.646,0.927 0.313,0.156 10 false *a
*a Matchmark


Using suction cups, position the back door glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the No. 1 and No. 2 back window glass spacers are engaged to the back door panel correctly.

·

Check the clearance between the back door panel and back door glass sub-assembly.




ii.

Lightly press the outer surface of the back door glass sub-assembly to ensure a close fit.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the back door glass sub-assembly using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




f.

Connect each connector and engage each clamp.


g.

When replacing the back door glass sub-assembly with a new one:

i.

Connect the rear washer hose and engage the clamp.



Hide 85345R 15.INSTALL REAR WASHER NOZZLE

HINT:

When reusing the back door glass.

Click hereVehicle Exterior>WIPER / WASHER>WASHER NOZZLE(for Rear Side)>INSTALLATION


Hide 85110R 16.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 17.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.