MALFUNCTION DESCRIPTION
These DTCs indicate that the temperature sensor value is abnormal. The cause of this malfunction may be one of the following:
| Area | Main Malfunction Description | Step |
|---|---|---|
| Inverter low-voltage circuit | The connectors are not connected properly | 2 |
| Hybrid cooling system | Coolant circulation abnormal (frozen or leaking, etc.) | 3 |
| Inside of inverter | Inverter with converter assembly internal circuit malfunction | 3 |
The motor generator control ECU detects the HV coolant temperature using the HV coolant temperature sensor built into the inverter with converter assembly. The motor generator control ECU uses signals from the coolant temperature sensor to check the effectiveness of the inverter cooling system. If necessary, the motor generator control ECU will limit inverter output to help prevent inverter overheating. The motor generator control ECU also detects malfunctions in the sensor based on the HV coolant temperature sensor values. The motor generator control ECU detects malfunctions in the HV coolant temperature sensor and its wiring.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A001C | Motor Electronics Coolant Temperature Sensor Circuit Voltage Out of Range | The actual inverter coolant temperature is high and difference between the estimated inverter coolant temperature and the actual temperature exceeds a threshold for 10 seconds.
(1 trip detection logic) |
·
Inverter cooling system ·
Cooling fan system ·
Grille shutter system ·
Inverter with converter assembly ·
Wire harness or connector |
Comes on | Master Warning Light:
Comes on |
| P0A001F | Motor Electronics Coolant Temperature Sensor Circuit Intermittent | Sudden change in HV coolant temperature sensor output or hunting:
Unusual sudden change in HV coolant temperature sensor output occurs and the offset continues for a certain period of time. Unusual sudden change in HV coolant temperature sensor output occurs repeatedly. (1 trip detection logic) |
·
Inverter cooling system ·
Cooling fan system ·
Grille shutter system ·
Inverter with converter assembly ·
Wire harness or connector |
Comes on | Master Warning Light:
Comes on |
| DTC No. | Data List |
|---|---|
| P0A001C | ·
Inverter Coolant Temperature ·
Ambient Temperature (Hybrid control system) ·
Inverter Water Pump Duty Ratio (Hybrid control system) ·
Inverter Water Pump Revolution (Hybrid control system) |
| P0A001F |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Turn the power switch on (READY) and wait for 90 seconds or more.
Check that there are no abnormalities (abnormal sounds, coolant leaks, DTC output, etc.).
Drive the vehicle for approximately 10 minutes referring to the following freeze frame data items: "Vehicle Speed".
Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Refer to the wiring diagram for the Cooling System.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Cooling System
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P0A001C or P0A001F only is output, or DTCs except the ones in the table below are also output. | A |
| Any of the following DTCs are also output. | B |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Insulation Malfunction | P1C7C49 | Hybrid/EV Battery Voltage System (A/C Area) Insulation Resistance Decreased |
| P1C7D49 | Hybrid/EV Battery Voltage System (Hybrid/EV Battery Area) Insulation Resistance Decreased | |
| P1C7E49 | Hybrid/EV Battery Voltage System (Transaxle Area) Insulation Resistance Decreased | |
| P1C7F49 | Hybrid/EV Battery Voltage System (Direct Current Area) Insulation Resistance Decreased | |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Sensor and actuator circuit malfunction | P0C7396 | Motor Electronics Coolant Pump "A" Component Internal Failure |
| P314A31 | Motor Electronics Coolant Pump "A" No Signal | |
| System malfunction | P0A9300 | Inverter "A" Cooling System |
P0A001C or P0A001F may be output as a result of the malfunctions indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Turn the power switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>P033500
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Cooling System
If the "Cooling System" inspection results are normal, perform the next step.
| Proceed to |
|---|
| NEXT |
NEXT