CLEARANCE WARNING ECU ASSEMBLY
Disconnect the F26 clearance warning ECU assembly connector.
Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F26-1 (IG) - F26-30 (E) | L - W-B | IG power source signal | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V | |||
| F26-30 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the F26 clearance warning ECU assembly connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F26-4 (BOF) - F26-30 (E) | BE - W-B | Power source for front sensor circuit | Power switch off | Below 1 V |
·
Power switch on (IG) ·
Intelligent clearance sonar system on |
11 to 14 V | |||
| F26-6 (E5) - F26-30 (E) | GR - W-B | Ground for front clearance sonar | Always | Below 1 V |
| F26-8 (SOF) - F26-30 (E) | G - W-B | Front sensor communication signal (Front clearance sonar sensor) | ·
Power switch on (READY) ·
Intelligent clearance sonar system on ·
Reverse (R) has been selected ·
Vehicle speed is less than approximately 10 km/h (6 mph) |
Pulse generation
(Refer to waveform 1) |
| F26-13 (EF) - F26-30 (E) | P - W-B | Ground for clearance warning buzzer | Always | Below 1 V |
| F26-14 (CBZ) - F26-13 (EF) | SB - P | Clearance warning buzzer signal | Buzzer sounding | Pulse generation
(Refer to waveform 2) |
| F26-15 (BBZ) - F26-16 (ER) | L - B | Clearance warning buzzer signal | Buzzer sounding | Pulse generation
(Refer to waveform 2) |
| F26-16 (ER) - F26-30 (E) | B - W-B | Ground for clearance warning buzzer | Always | Below 1 V |
| F26-22 (BOR) - F26-30 (E) | LG - W-B | Power source for rear sensor circuit | Power switch off | Below 1 V |
·
Power switch on (IG) ·
Intelligent clearance sonar system on |
11 to 14 V | |||
| F26-23 (E1) - F26-30 (E) | SB - W-B | Ground for rear clearance sonar | Always | Below 1 V |
| F26-24 (SOR) - F26-30 (E) | P - W-B | Rear sensor communication signal (Rear clearance sonar sensor) | ·
Power switch on (READY) ·
Intelligent clearance sonar system on ·
Reverse (R) has been selected ·
Vehicle speed is less than approximately 10 km/h (6 mph) |
Pulse generation
(Refer to waveform 1) |
Using an oscilloscope, check waveform 1.
Waveform 1 (Reference)
| Item | Content |
|---|---|
| Measurement terminal | ·
F26-8 (SOF) - F26-30 (E) ·
F26-24 (SOR) - F26-30 (E) |
| Measurement setting | 5 V/DIV., 1 ms./DIV. |
| Condition | ·
Power switch on (READY) ·
Intelligent clearance sonar system on ·
Reverse (R) has been selected ·
Vehicle speed is less than approximately 10 km/h (6 mph) |
Using an oscilloscope, check waveform 2.
Waveform 2 (Reference)
| Item | Content |
|---|---|
| Measurement terminal | ·
F26-14 (CBZ) - F26-13 (EF) ·
F26-15 (BBZ) - F26-16 (ER) |
| Measurement setting | 2 V/DIV., 500 μs./DIV. |
| Condition | Buzzer sounding |
The amplitude of the waveform changes according to the set volume.
HYBRID VEHICLE CONTROL ECU
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>TERMINALS OF ECU
ECM
w/ Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>TERMINALS OF ECM
w/o Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>TERMINALS OF ECM
METER CIRCUIT PLATE
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU