This circuit consists of the No. 1 clearance warning buzzer, No. 2 clearance warning buzzer and clearance warning ECU assembly. An ECU-excited type buzzer is used. The ECU operates the buzzers using a sound pattern that changes depending on the distance to the obstacle.
Check the operation of the No. 1 clearance warning buzzer and No. 2 clearance warning buzzer.
| Result | Proceed to |
|---|---|
| Buzzer does not sound when an obstacle is detected in front or at the rear of the vehicle. | A |
| Buzzer does not sound only when an obstacle is detected in front of the vehicle. | B |
| Buzzer does not sound only when an obstacle is detected at the rear of the vehicle. | C |
A
B
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / IPA/ICS/Clearance Sonar / Active Test.
Check that the front buzzer operates by performing the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Buzzer | No. 1 clearance warning buzzer | Stop or Operate | Confirm that the vehicle is stopped and the power switch is on (IG) |
| Tester Display |
|---|
| Front Buzzer |
The No. 1 clearance warning buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F26 clearance warning ECU assembly connector.
Disconnect the F27 No. 1 clearance warning buzzer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F26-14 (CBZ) - F27-1 (Z+) | Always | Below 1 Ω |
| F26-13 (EF) - F27-2 (Z-) | Always | Below 1 Ω |
| F26-14 (CBZ) or F27-1 (Z+) - Body ground | Always | 10 kΩ or higher |
| F26-13 (EF) or F27-2 (Z-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 clearance warning buzzer with a new or known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / IPA/ICS/Clearance Sonar / Active Test.
Check that the front buzzer operates by performing the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Buzzer | No. 1 clearance warning buzzer | Stop or Operate | Confirm that the vehicle is stopped and the power switch is on (IG) |
| Tester Display |
|---|
| Front Buzzer |
The No. 1 clearance warning buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / IPA/ICS/Clearance Sonar / Active Test.
Check that the rear buzzer operates by performing the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Buzzer | No. 2 clearance warning buzzer | Stop or Operate | Confirm that the vehicle is stopped and the power switch is on (IG) |
| Tester Display |
|---|
| Rear Buzzer |
The No. 2 clearance warning buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F26 clearance warning ECU assembly connector.
Disconnect the F42 No. 2 clearance warning buzzer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F26-15 (BBZ) - F42-1 (Z+) | Always | Below 1 Ω |
| F26-16 (ER) - F42-2 (Z-) | Always | Below 1 Ω |
| F26-15 (BBZ) or F42-1 (Z+) - Body ground | Always | 10 kΩ or higher |
| F26-16 (ER) or F42-2 (Z-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 2 clearance warning buzzer with a new or known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / IPA/ICS/Clearance Sonar / Active Test.
Check that the rear buzzer operates by performing the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Buzzer | No. 2 clearance warning buzzer | Stop or Operate | Confirm that the vehicle is stopped and the power switch is on (IG) |
| Tester Display |
|---|
| Rear Buzzer |
The No. 2 clearance warning buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG