Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › SIMPLE INTELLIGENT PARKING ASSIST SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0244874 SIMPLE INTELLIGENT PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  SIMPLE INTELLIGENT PARKING ASSIST SYSTEM  Main Switch Circuit  


DESCRIPTION

When the S-IPA switch is turned on, a signal is sent to the clearance warning ECU assembly. The simple intelligent parking assist system operates according to this signal.

WIRING DIAGRAM

E338895E02
3.094,1.083 4.25,1.396 1.156,0.313 10 false S-IPA Switch 5.521,1.813 6.781,2.271 1.26,0.458 10 false Clearance Warning ECU Assembly 5.646,0.542 6.208,0.708 0.563,0.167 10 false ISSW 5.521,1.646 6.083,1.813 0.563,0.167 10 false F26 5.406,0.448 5.969,0.615 0.563,0.167 10 false 29 2.958,0.427 3.521,0.594 0.563,0.167 10 false 5 4.25,0.417 4.813,0.583 0.563,0.167 10 false 7 4.031,0.458 4.594,0.625 0.563,0.167 10 false E 3.146,0.438 3.708,0.604 0.563,0.167 10 false IG 3.094,0.938 3.656,1.104 0.563,0.167 10 false F12 0.24,0.542 1.219,0.917 0.979,0.375 10 false from IG1-NO. 1 Relay 1.75,0.698 2.854,0.938 1.104,0.24 10 false ECU-IG1 NO. 4

PROCEDURE

1.READ VALUE USING GTS (IPA SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch to (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / IPA/ICS/Clearance Sonar / Data List / IPA Switch.


e.

Read the value when the S-IPA switch is pressed.

Body Electrical > IPA/ICS/Clearance Sonar > Data List
Tester Display Measurement Item Normal Condition
IPA Switch S-IPA signal ON: S-IPA switch on
OFF: S-IPA switch off

Result:
Proceed to
OK
NG



OK

NG

2.INSPECT S-IPA SWITCH
2.INSPECT S-IPA SWITCH

b.

Inspect the S-IPA switch.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MAIN SWITCH>INSPECTION

OK:

S-IPA switch is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (S-IPA SWITCH - AUXILIARY BATTERY)

NG

3.CHECK HARNESS AND CONNECTOR (S-IPA SWITCH - AUXILIARY BATTERY)
a.

Disconnect the F12 S-IPA switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F12-5 (IG) - F26-29 (ISSW) Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (S-IPA SWITCH - CLEARANCE WARNING ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (S-IPA SWITCH - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the F12 S-IPA switch connector.


b.

Disconnect the F26 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-7 (E) - F26-29 (ISSW) Always Below 1 Ω
F12-7 (E) or F26-29 (ISSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR