Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0244875 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  OPERATION CHECK  


BLIND SPOT MONITOR BEAM AXIS INSPECTION


HINT:

The blind spot monitor beam axis inspection is performed to confirm whether the sensor is transmitting radio waves.


a.

Procedure to enter Test Mode

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the blind spot monitor system on.


iv.

Turn the GTS on.


v.

Switch the blind spot monitor sensor to Test Mode using the GTS. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Beam Axis Inspection or BSM Slave Beam Axis Inspection.

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Inspection
50005 313 4202
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Inspection
50005 314 4203



BLIND SPOT MONITOR BEAM AXIS CONFIRMATION


HINT:

The blind spot monitor beam axis confirmation is performed to confirm whether the sensor's beam axis is correct, and perform adjustment of the beam axis by using reflector.


a.

When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.

E224418E12
0.083,1.448 0.365,1.646 0.281,0.198 10 false 2 m 1,3.979 1.927,4.177 0.927,0.198 10 false 6 m (19.69 ft.) 2.271,4 2.552,4.198 0.281,0.198 10 false 3 m 4.583,4 4.875,4.198 0.292,0.198 10 false 3 m 6.74,1.458 7.021,1.656 0.281,0.198 10 false 2 m 6.719,3.479 7.021,3.677 0.302,0.198 10 false 8 m 0.188,3.385 0.469,3.583 0.281,0.198 10 false 8 m 3.135,1.792 4,1.979 0.865,0.188 10 false Rear Bumper 0.865,0.292 2.479,0.531 1.615,0.24 12 false Left side of vehicle 4.625,0.26 6.396,0.49 1.771,0.229 12 false Right side of vehicle 1.292,4.344 2.375,4.542 1.083,0.198 10 false : Inspection Area 5.333,4.01 6.26,4.208 0.927,0.198 10 false 6 m (19.69 ft.) 4.479,4.167 5.031,4.365 0.552,0.198 10 false (9.85 ft.) 2.542,3.99 3.094,4.188 0.552,0.198 10 false (9.85 ft.) 0.031,3.792 0.677,3.99 0.646,0.198 10 false (26.25 ft.) 0.063,1.625 0.417,1.979 0.354,0.354 10 false (6.57 ft.) 6.542,3.823 7.135,4 0.594,0.177 10 false (26.25 ft.) 6.708,1.646 7.052,1.99 0.344,0.344 10 false (6.57 ft.)

NOTICE:
·

Perform this inspection on level ground.

·

Make sure that there are no metal objects around the vehicle or on the ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.

·

Do not place an object other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 9 m (29.53 ft.) x L 10 m (32.81 ft.) x H 4 m (13.13 ft.)) shown in the illustration.

·

Check that DTC C1ABB and DTC C1ABC are not output.




b.

Place the reflector.

i.

From the center of the rear bumper (center of the emblem), hang a weight with a pointed tip, and mark the rear center point of the vehicle on the ground (mark A).

E336342C01
2.667,2.5 3,2.417 false 3.031,2.479 3.365,2.563 false 4.917,0.417 5.5,0.75 true 4.833,1.417 5.5,1.167 true 4.75,0.344 5.063,0.5 0.313,0.156 10 false *a 2.521,2.438 2.833,2.594 0.313,0.156 10 false *b 4.677,1.344 4.99,1.5 0.313,0.156 10 false *c 3.396,2.51 3.552,2.708 0.156,0.198 10 false A
*a String *b Weight
*c Center point - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is aligned with mark A.



ii.

From the center of the front bumper (center of the emblem), hang a weight with a pointed tip, and mark the front center point of the vehicle on the ground (mark B).

E336343C01
1.188,0.5 1.521,0.583 false 3.396,2.583 3.729,2.5 false 3.771,2.417 4.104,2.5 false 0.688,1 1.521,1.167 true 1.031,0.427 1.344,0.583 0.313,0.156 10 false *a 4.125,2.438 4.438,2.594 0.313,0.156 10 false *b 0.521,0.917 0.833,1.073 0.313,0.156 10 false *c 3.292,2.521 3.5,2.75 0.208,0.229 10 false B
*a String *b Weight
*c Center point - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is aligned with mark (B).



iii.
E238824E01
1.439,1.257 1.206,1.541 false 3.022,1.262 3.177,1.627 false 0.633,1.258 1.092,0.453 false 1.092,0.453 1.292,0.453 false 1.321,0.355 2.528,0.516 1.207,0.161 10 Vehicle center line 1.1,1.532 1.261,1.693 0.161,0.161 10 A 3.186,1.624 3.347,1.785 0.161,0.161 10 B

Draw a vehicle center line so that it passes through mark A and B (front and rear center points).


iv.

Print out the following illustration on a large piece of paper.

E344977E01
2.333,2.208 3.135,2.958 3.135,2.958 3.344,2.958 false 2.385,6.969 3.552,6.333 3.552,6.333 3.76,6.333 false 4.542,4.427 5.167,3.396 5.167,3.396 5.375,3.396 false 1.125,5.542 1.333,5.542 1.333,5.542 2.01,4.448 false 0.115,0.063 1.49,0.26 1.375,0.198 12 false Printout: 3.385,2.875 4.917,3.115 1.531,0.24 10 false Line C 0.313,3.51 1.844,3.75 1.531,0.24 10 false Edge of rear bumper 5.427,3.313 6.844,3.688 1.417,0.375 10 false Vehicle center line 3.833,6.26 5.365,6.5 1.531,0.24 10 false Line C 0.979,5.469 2.51,5.708 1.531,0.24 10 false A 2.594,3.875 4.125,4.115 1.531,0.24 10 false 81.8° 2.552,4.885 4.083,5.125 1.531,0.24 10 false 81.8°


v.
E334361E02
1.063,2.635 1.333,2.635 1.333,2.635 1.823,2.896 false 2,2.188 2.531,2.563 2.531,2.563 2.74,2.563 false 0.979,1.458 1.146,1.458 1.146,1.458 1.823,1.969 true 0.813,1.385 1.125,1.583 0.313,0.198 10 false A 2.802,2.49 3.427,2.719 0.625,0.229 10 false Printout 0.094,2.552 0.99,2.948 0.896,0.396 10 false Vehicle center line 0.104,0.104 1.094,0.333 0.99,0.229 10 false Vehicle Rear

Place the printout on the floor with the point A aligned with the longitudinal center line of the vehicle.


vi.
E334362E03
0.563,4.125 0.667,4.125 0.667,4.125 0.75,3.75 false 2.875,4.115 2.76,4.115 2.76,4.115 2.656,3.729 false 0.729,3.146 0.833,3.146 0.833,3.146 1.094,3.542 false 2.458,2.594 2.26,2.594 2.26,2.594 1.729,3.167 true 2.604,3.208 2.49,3.208 2.49,3.208 2.292,3.521 false 2.042,4.031 1.927,4.031 1.927,4.031 1.813,3.385 false 2.365,0.167 2.25,0.167 2.25,0.167 1.698,0.552 false 0.354,0.156 1.229,0.365 0.875,0.208 10 false Vehicle front 2.448,0.104 3.292,0.563 0.844,0.458 10 false Vehicle center line 2.521,2.521 2.875,2.708 0.354,0.188 10 false A 0.333,3.052 0.865,3.323 0.531,0.271 10 false String 0.427,4.063 0.781,4.25 0.354,0.188 10 false D 2.917,4.042 3.271,4.229 0.354,0.188 10 false D 2.083,3.969 2.625,4.26 0.542,0.292 10 false Printout 2.656,3.125 3.135,3.406 0.479,0.281 10 false String

Align a piece of string with line C and mark point D at a distance of 3193 mm (10.48 ft.) from point A.


vii.

Set the reflector at the point D shown in the illustration below.

SST
09870-60000  (09870-60010)
09870-60040  

E334360E07
4.396,2.25 4.135,1.792 4.135,1.792 4.01,1.792 false 2.74,2.24 3,1.802 3,1.802 3.115,1.802 false 5.958,2.969 6.146,3.333 6.146,3.333 6.302,3.333 false 1.188,2.969 0.979,3.479 0.979,3.479 0.833,3.479 false 1.854,2.583 1.438,1.646 1.438,1.646 1.292,1.646 false 5.906,2.896 6.135,2.302 6.135,2.302 6.292,2.302 false 5.302,2.563 5.792,1.479 5.792,1.479 5.948,1.479 false 1.25,2.927 1,2.156 1,2.156 0.854,2.156 false 0.51,0.135 0.969,0.333 0.458,0.198 10 false LH: 3.448,0.083 3.906,0.281 0.458,0.198 10 false RH: 3.156,1.719 4.073,1.958 0.917,0.24 10 false Rear bumper 1.854,0.24 3.042,0.573 1.188,0.333 10 false Vehicle center line 4.188,0.281 5.646,0.542 1.458,0.26 10 false Vehicle center line 6.365,3.219 7.125,3.469 0.76,0.25 10 false Reflector 0.229,3.427 1.146,3.667 0.917,0.24 10 false Reflector 0.656,1.552 1.25,2.042 0.594,0.49 10 false 3193 mm (10.48 ft) 0.708,2.063 1.625,2.302 0.917,0.24 10 false D 6.344,2.25 6.792,2.583 0.448,0.333 10 false D 6,1.417 6.594,1.906 0.594,0.49 10 false 3193 mm (10.48 ft)

NOTICE:
·
E238830E39
0.115,1.313 0.781,1.688 0.667,0.375 10 false 495 mm (1.62 ft.)

Set the reflector so that its center is 495 mm (1.62 ft.) above the ground.

·
E338853E02
2.125,0.729 1.677,1.615 1.677,1.615 1.906,1.615 true 1.958,1.552 3.229,2.083 1.271,0.531 10 false Center of triangular pyramid

The center of the triangular pyramid is the reference point for the setting position and angle.

·

Set the reflector as shown in the illustration so that the center of the triangular pyramid faces the blind spot monitor sensor.

·

Perform the operation as precisely as possible.





c.

Perform the blind spot monitor beam axis display.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the blind spot monitor system on.


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Beam Axis Display or BSM Slave Beam Axis Display.

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Display
50005 313 4238
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Display
50005 314 4239

vi.

Check the results displayed for the BSM beam axis display.

Allowable Range:
Item Blind Spot Monitor Sensor LH (Master) Blind Spot Monitor Sensor RH (Slave)
Angle -3.6 to +3.6° -3.6 to +3.6°
Distance 2.0 to 3.0 m
(6.57 to 9.85 ft.)
2.0 to 3.0 m
(6.57 to 9.85 ft.)


HINT:

If the results are outside the allowable range, try again as the reflector setting position may be incorrect or a metal object may exist near the detection area.



vii.

Perform the blind spot monitor beam axis adjustment using the GTS. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Beam Axis Adjustment or BSM Slave Beam Axis Adjustment.

HINT:

When values on the axis display are in the allowable range, performing this adjustment compensates the values to the normal value.


Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Adjustment
50005 313 4231
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Adjustment
50005 314 4232



BLIND SPOT MONITOR INSTALLATION CONDITION INSPECTION


NOTICE:
·

Perform this inspection on level ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.



HINT:

The blind spot monitor sensor installation condition inspection is performed to confirm whether the sensor is perpendicular to the floor surface (+/-5°) by using a jig, and that the sensor is 16 to 24° from the line parallel to the vehicle center line.



b.

Attach a jig similar to the one shown in the illustration to the outward facing surface of the blind spot monitor sensor and check that the measurement or angle is within the allowable range to confirm that the blind spot monitor sensor is perpendicular to the floor surface (+/-5°).

HINT:

A digital angle meter can also be used to check that the blind spot monitor sensor is perpendicular to the floor surface or within the allowable range.


E233717E01
5.912,3.961 5.912,3.413 false 6.081,3.343 6.913,3.527 0.832,0.184 10 Floor surface 5.912,3.413 6.059,3.413 false 1.953,3.588 1.953,2.446 false 1.189,3.588 2.903,3.753 1.714,0.166 10 Blind Spot Monitor Sensor 3.125,3.441 4.816,3.645 1.691,0.205 10 Outward facing surface 2.298,2.115 2.983,3.504 false 0.161,0.064 1.797,0.248 1.635,0.184 10 Rear view of vehicle (RH): 5.056,1.213 5.582,0.619 false 5.582,0.619 5.729,0.619 false 5.764,0.556 6.208,0.793 0.444,0.236 10 Jig 4.611,3.251 4.874,3.251 false 4.909,3.19 5.483,3.426 0.574,0.236 10 Weight 2.983,3.504 3.095,3.504 false

E308579E01
1.729,0.875 3.177,1.427 1.448,0.552 10 false Hold this side against the blind spot monitor sensor RH. 4.031,0.885 5.479,1.438 1.448,0.552 10 false Hold this side against the blind spot monitor sensor LH. 3.271,1.719 3.646,1.99 0.375,0.271 10 false Top 1.292,2.677 2.74,3.229 1.448,0.552 10 false Position where string is to be secured 5.344,3.167 5.917,3.646 0.573,0.479 10 false 100 mm (3.94 in.) 2.615,4.385 2.99,4.656 0.375,0.271 10 false A 3.885,4.385 4.26,4.656 0.375,0.271 10 false B 3.104,3.313 3.479,3.583 0.375,0.271 10 false X 3.552,3.313 3.927,3.583 0.375,0.271 10 false Y 1.677,4.99 2.052,5.26 0.375,0.271 10 false + 5,5.021 5.375,5.292 0.375,0.271 10 false - 1.042,6.188 2.5,6.427 1.458,0.24 10 false : Allowable range

Standard:
A B
Blind spot monitor sensor RH 8 mm
(0.315 in.)
-8 mm
(-0.315 in.)
Blind spot monitor sensor LH 8 mm
(0.315 in.)
-8 mm
(-0.315 in.)

X Y
Blind spot monitor sensor RH 5° -5°
Blind spot monitor sensor LH 5° -5°



c.
E308578E01
2.906,1.115 2.719,0.604 2.719,0.604 2.542,0.604 false 1.396,1.99 1.458,1.74 1.458,1.74 1.615,1.74 false 1.448,3.531 1.656,4.125 1.656,4.125 1.813,4.125 false 0.552,4.021 0.635,4.438 0.635,4.438 0.74,4.438 false 0.771,3.583 0.844,4 0.844,4 0.948,4 false 0.042,0.042 1.563,0.302 1.521,0.26 12 false Vehicle rear (LH): 1.188,0.854 2.125,1.073 0.938,0.219 10 false Vehicle front 1.313,0.5 2.521,0.719 1.208,0.219 10 false Vehicle center line 1.677,1.667 2.771,2.052 1.094,0.385 10 false Stud bolt center line 1.625,2.448 2.802,2.833 1.177,0.385 10 false 104 mm (4.09 in.) 1.969,3.729 2.906,3.948 0.938,0.219 10 false Vehicle rear 0.99,3.896 1.198,4.104 0.208,0.208 10 false y 1.865,4.031 2.802,4.25 0.938,0.219 10 false Stud bolt 0.813,4.354 3.375,4.594 2.563,0.24 10 false Line parallel to the vehicle center line 0.708,3.115 0.917,3.323 0.208,0.208 10 false A

Using the sensor installation stud bolt center lines as a reference, check that the position or angle of the stud bolts are as shown in the illustration.

Standard:
Dimension Specified Value
y 29 to 42 mm
(1.14 to 1.65 in.)

Degree Specified Value
A 16 to 24 degree