Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0244875 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1ABD  Short to +B in Buzzer  C1ABE  Short to GND or Open in Buzzer  


DESCRIPTION

·

DTC C1ABD is stored when the blind spot monitor sensor RH detects a +B short in the RCTA buzzer (blind spot monitor buzzer) circuit.

·

DTC C1ABE is stored when the blind spot monitor sensor RH detects a ground short or open in the RCTA buzzer (blind spot monitor buzzer) circuit.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1ABD Short to +B in Buzzer
Both of the following conditions are met:
·

The blind spot monitor system is on.

·

The blind spot monitor sensor is not sending voltage to the buzzer but the buzzer receives voltage above a specified level for a specified period of time.


·

Blind spot monitor sensor RH

·

RCTA buzzer (blind spot monitor buzzer)

·

Harness or connector


C1ABE Short to GND or Open in Buzzer
Both of the following conditions are met:
·

The blind spot monitor system is on.

·

The current flowing to the buzzer is below a specified value when buzzer operation voltage is being sent to the buzzer.


·

Blind spot monitor sensor RH

·

RCTA buzzer (blind spot monitor buzzer)

·

Harness or connector



WIRING DIAGRAM

E254403E59
0.156,1.021 1.563,1.219 1.406,0.198 10 false from IG1-NO. 1 Relay 3.229,1.521 5.125,1.875 1.896,0.354 10 false RCTA Buzzer (Blind Spot Monitor Buzzer) 5.594,1.927 5.885,2.125 0.292,0.198 10 false M56 5.615,2.083 6.813,2.406 1.198,0.323 10 false Blind Spot Monitor Sensor RH 3.354,0.927 3.5,1.104 0.146,0.177 10 false 1 5.646,1.021 5.979,1.219 0.333,0.198 10 false BUZ 5.479,0.917 5.625,1.094 0.146,0.177 10 false 3 4.698,0.917 4.844,1.094 0.146,0.177 10 false 2 2.063,1.198 3.042,1.406 0.979,0.208 10 false ECU-IG1 NO. 4 4.302,1.021 4.635,1.219 0.333,0.198 10 false BZN 3.51,1.01 3.844,1.208 0.333,0.198 10 false BZP 3.229,1.333 4.229,1.531 1,0.198 10 false M57*1, M58*2 0.229,1.885 1.427,2.094 1.198,0.208 10 false *1: for LHD 0.25,2.229 1.448,2.438 1.198,0.208 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is turned on.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Turn the power switch on (IG).


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BLIND SPOT MONITOR SENSOR RH AND AUXILIARY BATTERY)
2.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BLIND SPOT MONITOR SENSOR RH AND AUXILIARY BATTERY)
a.

Disconnect the M57*1 or M58*2 RCTA buzzer (blind spot monitor buzzer) connector.

*1: for LHD

*2: for RHD



b.

Disconnect the M56 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
M57-2 (BZN) - M56-3 (BUZ) Always Below 1 Ω
M57-2 (BZN) or M56-3 (BUZ) - Body ground Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
M58-2 (BZN) - M56-3 (BUZ) Always Below 1 Ω
M58-2 (BZN) or M56-3 (BUZ) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (for LHD):
Tester Connection Switch Condition Specified Condition
M57-2 (BZN) or M56-3 (BUZ) - Body ground Power switch on (IG) Below 1 V
M57-1 (BZP) - Body ground Power switch on (IG) 11 to 14 V
M57-1 (BZP) - Body ground Power switch off Below 1 V


Standard Voltage (for RHD):
Tester Connection Switch Condition Specified Condition
M58-2 (BZN) or M56-3 (BUZ) - Body ground Power switch on (IG) Below 1 V
M58-1 (BZP) - Body ground Power switch on (IG) 11 to 14 V
M58-1 (BZP) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK RCTA BUZZER (BLIND SPOT MONITOR BUZZER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RCTA BUZZER (BLIND SPOT MONITOR BUZZER)
a.

Replace the RCTA buzzer (blind spot monitor buzzer).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR CROSSING TRAFFIC ALERT BUZZER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

DTC C1ABD and C1ABE are not output.



Result:
Proceed to
OK
NG



OK

END (RCTA BUZZER [BLIND SPOT MONITOR BUZZER] WAS DEFECTIVE)

NG