Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0244875 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB1  Short to +B in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a short to +B in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB1 Short to +B in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time


·

Outer mirror RH

·

Outer rear view mirror assembly RH

·

Wire harness or connector

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E221720E38
2.563,1.24 2.698,1.396 0.135,0.156 10 false 2 3.51,1.219 3.646,1.375 0.135,0.156 10 false 1 5.375,1.24 5.531,1.427 0.156,0.188 10 false 4 3.031,1.219 3.49,1.396 0.458,0.177 10 false BSR+ 5.573,1.354 5.979,1.51 0.406,0.156 10 false OMIR 3.25,1.729 3.719,1.896 0.469,0.167 10 false - 0.99,2.188 1.365,2.344 0.375,0.156 10 false IND2 0.75,3.385 1.219,3.583 0.469,0.198 10 false I8 5.406,3.396 5.854,3.573 0.448,0.177 10 false M56 2.354,1.333 2.49,1.49 0.135,0.156 10 false + 2.375,1.802 2.51,1.958 0.135,0.156 10 false - 2.563,1.719 2.698,1.875 0.135,0.156 10 false 1 3.51,1.708 3.76,1.917 0.25,0.208 10 false 8 0.979,2.365 3.115,2.531 2.135,0.167 10 false Outer Mirror RH 5.406,3.573 6.604,3.885 1.198,0.313 10 false Blind Spot Monitor Sensor RH 0.969,2.656 3.375,2.854 2.406,0.198 10 false (Outer Rear View Mirror Indicator RH) 0.792,3.583 3.167,3.76 2.375,0.177 10 false Outer Rear View Mirror Assembly RH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Turn the power switch on (IG).


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the M56 blind spot monitor sensor RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M56-4 (OMIR) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the IND2 outer mirror RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M56-4 (OMIR) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the I8 outer rear view mirror assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M56-4 (OMIR) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR