Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0244900 DYNAMIC RADAR CRUISE CONTROL SYSTEM Y

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Perform the following procedure to troubleshoot the dynamic radar cruise control system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT AUXILIARY BATTERY VOLTAGE
2.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY*
3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY*


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Turn the GTS on.


f.

Turn the cruise control main switch (ON/OFF button) on.


g.

Enter the following menus: Powertrain / Pre-Crash 2 / Utility / Beam Axis Misalignment Reading.


h.

Check the amount of misalignment and make a note.

Body Electrical > Pre-Crash 2 > Utility
Tester Display
Front Beam Axis Misalignment Reading
50005 220 5405

i.

Enter the following menus: Powertrain / Pre-Crash 2 / Utility / Beam Axis Offset Reading.


j.

Check the amount of misalignment and make a note.

Body Electrical > Pre-Crash 2 > Utility
Tester Display
Front Beam Axis Offset Reading
50005 220 5406

k.

Calculate the "Dealership Axis Offset Angle (with On-line Calibration Angle)" using the values "Front Beam Axis Misalignment Reading" and "Front Beam Axis Offset Reading".

i.

"Dealership Axis Offset Angle (with On-line Calibration Angle)" = "Front Beam Axis Misalignment Reading" - "Front Beam Axis Offset Reading"

Standard:
Dealership Axis Offset Angle (with On-line Calibration Angle):
Vertical -2.2 to 1.6 deg.
Horizontal -0.6 to 0.6 deg.




Result:
Result Proceed to
The dealership axis offset angle (with on-line calibration angle) is within the specified range. A
The dealership axis offset angle (with on-line calibration angle) is not within the specified range. B



A

4.CHECK CAN COMMUNICATION SYSTEM*

B

12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check that the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

5.CHECK METER / GAUGE SYSTEM*

B

5.CHECK METER / GAUGE SYSTEM*
a.

Use the GTS to check if the meter / gauge system is functioning normally.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
Meter / gauge system DTCs are not output A
Meter / gauge system DTCs are output B



A

6.CHECK ELECTRONICALLY CONTROLLED BRAKE SYSTEM

B

6.CHECK ELECTRONICALLY CONTROLLED BRAKE SYSTEM
a.

Use the GTS to check if the electronically controlled brake system is functioning normally.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs is not output A
Electronically controlled brake system DTCs are output B



A

7.CHECK FOR DTCs (DYNAMIC RADAR CRUISE CONTROL SYSTEM)

B

7.CHECK FOR DTCs (DYNAMIC RADAR CRUISE CONTROL SYSTEM)
a.

Check for DTCs and note any codes that are output.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 399
Powertrain > Radar Cruise2 > Trouble Codes
50001 197

b.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 399
Powertrain > Radar Cruise2 > Clear DTCs
50002 197

c.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 399
Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

8.PROBLEM SYMPTOMS TABLE

B

8.PROBLEM SYMPTOMS TABLE
HINT:

Refer to Problem Symptoms Table.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

9.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

10.ADJUST, REPAIR OR REPLACE
NOTICE:

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

11.CONFIRMATION TEST
11.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END

12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*