Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0244900 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P163181  Communication Error from ECM to VSC Invalid Serial Data Received  


DESCRIPTION

The hybrid vehicle control ECU sends signals such as A/T information signals, dynamic radar cruise control operation signals, brake operation demand signals, and buzzer operation demand signals to the skid control ECU (brake booster with master cylinder assembly) when the dynamic radar cruise control is operating. Therefore, if the skid control ECU (brake booster with master cylinder assembly) detects a communication error with the hybrid vehicle control ECU, it sends a malfunction signal back to the hybrid vehicle control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
P163181 Communication Error from ECM to VSC Invalid Serial Data Received
w/o Full-speed range following function:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU continuously receives a logical error signal from the skid control ECU (brake booster with master cylinder assembly) for approximately 1 second or more.


w/ Full-speed range following function:
·

While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU continuously receives a logical error signal from the skid control ECU (brake booster with master cylinder assembly) for approximately 1 second or more.


·

CAN communication system

·

Hybrid vehicle control ECU

·

Skid control ECU (brake booster with master cylinder assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output OK
CAN communication system DTCs are output NG



OK

2.CHECK FOR DTCs (RADAR CRUISE 1)

NG

2.CHECK FOR DTCs (RADAR CRUISE 1)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 399

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Turn the power switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).

3.

w/ Full-speed range following function: Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.

w/o Full-speed range following function: Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 399

Result:
Result Proceed to
DTC P163181 is not output A
DTC P163181 is output B



A

B

3.REPLACE HYBRID VEHICLE CONTROL ECU
3.REPLACE HYBRID VEHICLE CONTROL ECU
a.

Replace the hybrid vehicle control ECU with a new one.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (RADAR CRUISE 1)
4.CHECK FOR DTCs (RADAR CRUISE 1)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 399

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Turn the power switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).

3.

w/ Full-speed range following function: Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.

w/o Full-speed range following function: Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 399

Result:
Result Proceed to
DTC P163181 is not output A
DTC P163181 is output B



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)