Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0244900 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

Based on dynamic radar cruise control system operation, the driving support ECU assembly provides warnings to the driver by sounding the skid control buzzer.

DTC C1A4A is stored when a malfunction is detected in the skid control buzzer circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit
w/o Full-speed range following function:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, the driving support ECU assembly detects a malfunction in the skid control buzzer circuit for approximately 0.4 seconds or more.


w/ Full-speed range following function:
·

While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, the driving support ECU assembly detects a malfunction in the skid control buzzer circuit for approximately 0.4 seconds or more.


·

Skid control buzzer

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Harness or connector



WIRING DIAGRAM

B403796E62
5.031,2.188 6.958,2.5 1.927,0.313 10 false Driving Support ECU assembly 3.427,1.167 4.688,1.552 1.26,0.385 10 false Skid Control Buzzer 2.083,0.844 3.125,1.229 1.042,0.385 10 false ECU-IG1 NO. 4 3.573,0.719 4.042,0.917 0.469,0.198 10 false IG1 4.25,0.719 4.573,0.917 0.323,0.198 10 false BZ 5.521,0.708 5.844,0.906 0.323,0.198 10 false BZ 0.135,0.677 2.281,0.875 2.146,0.198 10 false from IG1-NO. 1 Relay 3.396,0.615 3.563,0.823 0.167,0.208 10 false 2 4.5,0.615 4.667,0.823 0.167,0.208 10 false 1 5.365,0.625 5.521,0.823 0.156,0.198 10 false 3 3.448,1.031 3.906,1.229 0.458,0.198 10 false F41 5.042,2.031 5.5,2.229 0.458,0.198 10 false F40

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



PROCEDURE

1.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Check for DTCs of the pre-crash safety system.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
HINT:
·

w/o Full-speed range following function:

The dynamic radar cruise control system only stores DTC C1A4A when the vehicle speed reaches 36 km/h (22 mph), however the pre-crash safety system stores this DTC at any vehicle speed. If DTC C1A4A is stored by the pre-crash safety system, perform troubleshooting of the pre-crash safety system first.

·

w/ Full-speed range following function:

The dynamic radar cruise control system only stores DTC C1A4A when the vehicle speed reaches 5 km/h (3 mph), however the pre-crash safety system stores this DTC at any vehicle speed. If DTC C1A4A is stored by the pre-crash safety system, perform troubleshooting of the pre-crash safety system first.




Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

2.CHECK FOR DTCs (RADAR CRUISE 2)

B

2.CHECK FOR DTCs (RADAR CRUISE 2)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the power switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).

3.

w/ Full-speed range following function: Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.

w/o Full-speed range following function: Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

B

3.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)
3.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)
a.

Turn the power switch on (IG).


b.

Check that the skid control buzzer is sounds.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER>INSPECTION


Result:
Result Proceed to
The skid control buzzer does not sound when the power switch is on (IG). A
The skid control buzzer sounds continuously when the power switch is on (IG). B



A

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - AUXILIARY BATTERY)

B

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - DRIVING SUPPORT ECU ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - AUXILIARY BATTERY)
a.
A380147C02
0.344,1 0.719,1.25 0.375,0.25 1.917,1.604 2.208,1.917 2.208,1.917 2.354,1.917 true 0.417,1.042 0.875,1.24 0.458,0.198 10 false F41 0.177,0.115 0.49,0.313 0.313,0.198 10 false *a 2.406,1.823 2.865,2.021 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer)


Disconnect the skid control buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F41-2 (IG1) - Body ground Power switch on (IG) 11 to 14 V
F41-2 (IG1) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the F41 skid control buzzer connector.


b.

Disconnect the F40 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F41-1 (BZ) - F40-3 (BZ) Always Below 1 Ω
F41-1 (BZ) or F40-3 (BZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT SKID CONTROL BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT SKID CONTROL BUZZER
a.

b.

Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the F41 skid control buzzer connector.


b.

Disconnect the F40 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F41-1 (BZ) - F40-3 (BZ) Always Below 1 Ω
F41-1 (BZ) or F40-3 (BZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR